// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2009
 * Marvell Semiconductor <www.marvell.com>
 * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
 *
 * Derived from drivers/spi/mpc8xxx_spi.c
 */

#include <common.h>
#include <dm.h>
#include <malloc.h>
#include <spi.h>
#include <asm/io.h>
#include <asm/arch/soc.h>
#ifdef CONFIG_KIRKWOOD
#include <asm/arch/mpp.h>
#endif
#include <asm/arch-mvebu/spi.h>

static void _spi_cs_activate(struct kwspi_registers *reg)
{
        setbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
}

static void _spi_cs_deactivate(struct kwspi_registers *reg)
{
        clrbits_le32(&reg->ctrl, KWSPI_CSN_ACT);
}

static int _spi_xfer(struct kwspi_registers *reg, unsigned int bitlen,
                     const void *dout, void *din, unsigned long flags)
{
        unsigned int tmpdout, tmpdin;
        int tm, isread = 0;

        debug("spi_xfer: dout %p din %p bitlen %u\n", dout, din, bitlen);

        if (flags & SPI_XFER_BEGIN)
                _spi_cs_activate(reg);

        /*
         * handle data in 8-bit chunks
         * TBD: 2byte xfer mode to be enabled
         */
        clrsetbits_le32(&reg->cfg, KWSPI_XFERLEN_MASK, KWSPI_XFERLEN_1BYTE);

        while (bitlen > 4) {
                debug("loopstart bitlen %d\n", bitlen);
                tmpdout = 0;

                /* Shift data so it's msb-justified */
                if (dout)
                        tmpdout = *(u32 *)dout & 0xff;

                clrbits_le32(&reg->irq_cause, KWSPI_SMEMRDIRQ);
                writel(tmpdout, &reg->dout);    /* Write the data out */
                debug("*** spi_xfer: ... %08x written, bitlen %d\n",
                      tmpdout, bitlen);

                /*
                 * Wait for SPI transmit to get out
                 * or time out (1 second = 1000 ms)
                 * The NE event must be read and cleared first
                 */
                for (tm = 0, isread = 0; tm < KWSPI_TIMEOUT; ++tm) {
                        if (readl(&reg->irq_cause) & KWSPI_SMEMRDIRQ) {
                                isread = 1;
                                tmpdin = readl(&reg->din);
                                debug("spi_xfer: din %p..%08x read\n",
                                      din, tmpdin);

                                if (din) {
                                        *((u8 *)din) = (u8)tmpdin;
                                        din += 1;
                                }
                                if (dout)
                                        dout += 1;
                                bitlen -= 8;
                        }
                        if (isread)
                                break;
                }
                if (tm >= KWSPI_TIMEOUT)
                        printf("*** spi_xfer: Time out during SPI transfer\n");

                debug("loopend bitlen %d\n", bitlen);
        }

        if (flags & SPI_XFER_END)
                _spi_cs_deactivate(reg);

        return 0;
}

#ifndef CONFIG_DM_SPI

static struct kwspi_registers *spireg =
        (struct kwspi_registers *)MVEBU_SPI_BASE;

#ifdef CONFIG_KIRKWOOD
static u32 cs_spi_mpp_back[2];
#endif

struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
                                unsigned int max_hz, unsigned int mode)
{
        struct spi_slave *slave;
        u32 data;
#ifdef CONFIG_KIRKWOOD
        static const u32 kwspi_mpp_config[2][2] = {
                { MPP0_SPI_SCn, 0 }, /* if cs == 0 */
                { MPP7_SPI_SCn, 0 } /* if cs != 0 */
        };
#endif

        if (!spi_cs_is_valid(bus, cs))
                return NULL;

        slave = spi_alloc_slave_base(bus, cs);
        if (!slave)
                return NULL;

        writel(KWSPI_SMEMRDY, &spireg->ctrl);

        /* calculate spi clock prescaller using max_hz */
        data = ((CONFIG_SYS_TCLK / 2) / max_hz) + 0x10;
        data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
        data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;

        /* program spi clock prescaller using max_hz */
        writel(KWSPI_ADRLEN_3BYTE | data, &spireg->cfg);
        debug("data = 0x%08x\n", data);

        writel(KWSPI_SMEMRDIRQ, &spireg->irq_cause);
        writel(KWSPI_IRQMASK, &spireg->irq_mask);

#ifdef CONFIG_KIRKWOOD
        /* program mpp registers to select  SPI_CSn */
        kirkwood_mpp_conf(kwspi_mpp_config[cs ? 1 : 0], cs_spi_mpp_back);
#endif

        return slave;
}

void spi_free_slave(struct spi_slave *slave)
{
#ifdef CONFIG_KIRKWOOD
        kirkwood_mpp_conf(cs_spi_mpp_back, NULL);
#endif
        free(slave);
}

#if defined(CONFIG_SYS_KW_SPI_MPP)
u32 spi_mpp_backup[4];
#endif

__attribute__((weak)) int board_spi_claim_bus(struct spi_slave *slave)
{
        return 0;
}

int spi_claim_bus(struct spi_slave *slave)
{
#if defined(CONFIG_SYS_KW_SPI_MPP)
        u32 config;
        u32 spi_mpp_config[4];

        config = CONFIG_SYS_KW_SPI_MPP;

        if (config & MOSI_MPP6)
                spi_mpp_config[0] = MPP6_SPI_MOSI;
        else
                spi_mpp_config[0] = MPP1_SPI_MOSI;

        if (config & SCK_MPP10)
                spi_mpp_config[1] = MPP10_SPI_SCK;
        else
                spi_mpp_config[1] = MPP2_SPI_SCK;

        if (config & MISO_MPP11)
                spi_mpp_config[2] = MPP11_SPI_MISO;
        else
                spi_mpp_config[2] = MPP3_SPI_MISO;

        spi_mpp_config[3] = 0;
        spi_mpp_backup[3] = 0;

        /* set new spi mpp and save current mpp config */
        kirkwood_mpp_conf(spi_mpp_config, spi_mpp_backup);
#endif

        return board_spi_claim_bus(slave);
}

__attribute__((weak)) void board_spi_release_bus(struct spi_slave *slave)
{
}

void spi_release_bus(struct spi_slave *slave)
{
#if defined(CONFIG_SYS_KW_SPI_MPP)
        kirkwood_mpp_conf(spi_mpp_backup, NULL);
#endif

        board_spi_release_bus(slave);
}

#ifndef CONFIG_SPI_CS_IS_VALID
/*
 * you can define this function board specific
 * define above CONFIG in board specific config file and
 * provide the function in board specific src file
 */
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
        return bus == 0 && (cs == 0 || cs == 1);
}
#endif

void spi_init(void)
{
}

void spi_cs_activate(struct spi_slave *slave)
{
        _spi_cs_activate(spireg);
}

void spi_cs_deactivate(struct spi_slave *slave)
{
        _spi_cs_deactivate(spireg);
}

int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
             const void *dout, void *din, unsigned long flags)
{
        return _spi_xfer(spireg, bitlen, dout, din, flags);
}

#else

/* Here now the DM part */

struct mvebu_spi_dev {
        bool                    is_errata_50mhz_ac;
};

struct mvebu_spi_platdata {
        struct kwspi_registers *spireg;
};

struct mvebu_spi_priv {
        struct kwspi_registers *spireg;
};

static int mvebu_spi_set_speed(struct udevice *bus, uint hz)
{
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
        struct kwspi_registers *reg = plat->spireg;
        u32 data;

        /* calculate spi clock prescaller using max_hz */
        data = ((CONFIG_SYS_TCLK / 2) / hz) + 0x10;
        data = data < KWSPI_CLKPRESCL_MIN ? KWSPI_CLKPRESCL_MIN : data;
        data = data > KWSPI_CLKPRESCL_MASK ? KWSPI_CLKPRESCL_MASK : data;

        /* program spi clock prescaler using max_hz */
        writel(KWSPI_ADRLEN_3BYTE | data, &reg->cfg);
        debug("data = 0x%08x\n", data);

        return 0;
}

static void mvebu_spi_50mhz_ac_timing_erratum(struct udevice *bus, uint mode)
{
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
        struct kwspi_registers *reg = plat->spireg;
        u32 data;

        /*
         * Erratum description: (Erratum NO. FE-9144572) The device
         * SPI interface supports frequencies of up to 50 MHz.
         * However, due to this erratum, when the device core clock is
         * 250 MHz and the SPI interfaces is configured for 50MHz SPI
         * clock and CPOL=CPHA=1 there might occur data corruption on
         * reads from the SPI device.
         * Erratum Workaround:
         * Work in one of the following configurations:
         * 1. Set CPOL=CPHA=0 in "SPI Interface Configuration
         * Register".
         * 2. Set TMISO_SAMPLE value to 0x2 in "SPI Timing Parameters 1
         * Register" before setting the interface.
         */
        data = readl(&reg->timing1);
        data &= ~KW_SPI_TMISO_SAMPLE_MASK;

        if (CONFIG_SYS_TCLK == 250000000 &&
            mode & SPI_CPOL &&
            mode & SPI_CPHA)
                data |= KW_SPI_TMISO_SAMPLE_2;
        else
                data |= KW_SPI_TMISO_SAMPLE_1;

        writel(data, &reg->timing1);
}

static int mvebu_spi_set_mode(struct udevice *bus, uint mode)
{
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
        struct kwspi_registers *reg = plat->spireg;
        const struct mvebu_spi_dev *drvdata;
        u32 data = readl(&reg->cfg);

        data &= ~(KWSPI_CPHA | KWSPI_CPOL | KWSPI_RXLSBF | KWSPI_TXLSBF);

        if (mode & SPI_CPHA)
                data |= KWSPI_CPHA;
        if (mode & SPI_CPOL)
                data |= KWSPI_CPOL;
        if (mode & SPI_LSB_FIRST)
                data |= (KWSPI_RXLSBF | KWSPI_TXLSBF);

        writel(data, &reg->cfg);

        drvdata = (struct mvebu_spi_dev *)dev_get_driver_data(bus);
        if (drvdata->is_errata_50mhz_ac)
                mvebu_spi_50mhz_ac_timing_erratum(bus, mode);

        return 0;
}

static int mvebu_spi_xfer(struct udevice *dev, unsigned int bitlen,
                          const void *dout, void *din, unsigned long flags)
{
        struct udevice *bus = dev->parent;
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

        return _spi_xfer(plat->spireg, bitlen, dout, din, flags);
}

static int mvebu_spi_claim_bus(struct udevice *dev)
{
        struct udevice *bus = dev->parent;
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

        /* Configure the chip-select in the CTRL register */
        clrsetbits_le32(&plat->spireg->ctrl,
                        KWSPI_CS_MASK << KWSPI_CS_SHIFT,
                        spi_chip_select(dev) << KWSPI_CS_SHIFT);

        return 0;
}

static int mvebu_spi_probe(struct udevice *bus)
{
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);
        struct kwspi_registers *reg = plat->spireg;

        writel(KWSPI_SMEMRDY, &reg->ctrl);
        writel(KWSPI_SMEMRDIRQ, &reg->irq_cause);
        writel(KWSPI_IRQMASK, &reg->irq_mask);

        return 0;
}

static int mvebu_spi_ofdata_to_platdata(struct udevice *bus)
{
        struct mvebu_spi_platdata *plat = dev_get_platdata(bus);

        plat->spireg = (struct kwspi_registers *)devfdt_get_addr(bus);

        return 0;
}

static const struct dm_spi_ops mvebu_spi_ops = {
        .claim_bus      = mvebu_spi_claim_bus,
        .xfer           = mvebu_spi_xfer,
        .set_speed      = mvebu_spi_set_speed,
        .set_mode       = mvebu_spi_set_mode,
        /*
         * cs_info is not needed, since we require all chip selects to be
         * in the device tree explicitly
         */
};

static const struct mvebu_spi_dev armada_xp_spi_dev_data = {
        .is_errata_50mhz_ac = false,
};

static const struct mvebu_spi_dev armada_375_spi_dev_data = {
        .is_errata_50mhz_ac = false,
};

static const struct mvebu_spi_dev armada_380_spi_dev_data = {
        .is_errata_50mhz_ac = true,
};

static const struct udevice_id mvebu_spi_ids[] = {
        {
                .compatible = "marvell,armada-375-spi",
                .data = (ulong)&armada_375_spi_dev_data
        },
        {
                .compatible = "marvell,armada-380-spi",
                .data = (ulong)&armada_380_spi_dev_data
        },
        {
                .compatible = "marvell,armada-xp-spi",
                .data = (ulong)&armada_xp_spi_dev_data
        },
        { }
};

U_BOOT_DRIVER(mvebu_spi) = {
        .name = "mvebu_spi",
        .id = UCLASS_SPI,
        .of_match = mvebu_spi_ids,
        .ops = &mvebu_spi_ops,
        .ofdata_to_platdata = mvebu_spi_ofdata_to_platdata,
        .platdata_auto_alloc_size = sizeof(struct mvebu_spi_platdata),
        .priv_auto_alloc_size = sizeof(struct mvebu_spi_priv),
        .probe = mvebu_spi_probe,
};
#endif