LXR uboot/include/configs/mx6cuboxi.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * Copyright (C) 2015 Freescale Semiconductor, Inc.
   4 *
   5 * Configuration settings for the SolidRun mx6 based boards
   6 */
   7#ifndef __MX6CUBOXI_CONFIG_H
   8#define __MX6CUBOXI_CONFIG_H
   9
  10#include "mx6_common.h"
  11
  12#include "imx6_spl.h"
  13
  14#define CONFIG_IMX_THERMAL
  15
  16#define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  17#define CONFIG_MXC_UART
  18
  19/* MMC Configs */
  20#define CONFIG_SYS_FSL_ESDHC_ADDR       USDHC2_BASE_ADDR
  21
  22/* SATA Configuration */
  23#ifdef CONFIG_CMD_SATA
  24#define CONFIG_SYS_SATA_MAX_DEVICE      1
  25#define CONFIG_DWC_AHSATA_PORT_ID       0
  26#define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  27#define CONFIG_LBA48
  28#endif
  29
  30/* Ethernet Configuration */
  31#define CONFIG_FEC_MXC
  32#define CONFIG_MII
  33#define IMX_FEC_BASE                    ENET_BASE_ADDR
  34#define CONFIG_FEC_XCV_TYPE             RGMII
  35#define CONFIG_FEC_MXC_PHYADDR          0
  36#define CONFIG_PHY_ATHEROS
  37
  38/* Framebuffer */
  39#define CONFIG_VIDEO_IPUV3
  40#define CONFIG_VIDEO_BMP_RLE8
  41#define CONFIG_SPLASH_SCREEN
  42#define CONFIG_SPLASH_SCREEN_ALIGN
  43#define CONFIG_BMP_16BPP
  44#define CONFIG_VIDEO_LOGO
  45#define CONFIG_VIDEO_BMP_LOGO
  46#define CONFIG_IMX_HDMI
  47#define CONFIG_IMX_VIDEO_SKIP
  48
  49/* USB */
  50#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  51#define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  52#define CONFIG_MXC_USB_FLAGS            0
  53#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  54#define CONFIG_PREBOOT \
  55        "if hdmidet; then " \
  56                "usb start; "                  \
  57                "setenv stdin  serial,usbkbd; "\
  58                "setenv stdout serial,vga; "   \
  59                "setenv stderr serial,vga; "   \
  60        "else " \
  61                "setenv stdin  serial; " \
  62                "setenv stdout serial; " \
  63                "setenv stderr serial; " \
  64        "fi;"
  65
  66/* Command definition */
  67
  68#define CONFIG_MXC_UART_BASE    UART1_BASE
  69#define CONSOLE_DEV     "ttymxc0"
  70#define CONFIG_SYS_FSL_USDHC_NUM        1
  71#define CONFIG_SYS_MMC_ENV_DEV          0       /* SDHC2 */
  72
  73#ifndef CONFIG_SPL_BUILD
  74#define CONFIG_EXTRA_ENV_SETTINGS \
  75        "fdtfile=undefined\0" \
  76        "fdt_addr_r=0x18000000\0" \
  77        "fdt_addr=0x18000000\0" \
  78        "kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0"  \
  79        "pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
  80        "scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
  81        "ramdisk_addr_r=0x13000000\0" \
  82        "ramdiskaddr=0x13000000\0" \
  83        "initrd_high=0xffffffff\0" \
  84        "fdt_high=0xffffffff\0" \
  85        "ip_dyn=yes\0" \
  86        "console=" CONSOLE_DEV ",115200\0" \
  87        "bootm_size=0x10000000\0" \
  88        "mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
  89        "finduuid=part uuid mmc 0:1 uuid\0" \
  90        "update_sd_firmware=" \
  91                "if test ${ip_dyn} = yes; then " \
  92                        "setenv get_cmd dhcp; " \
  93                "else " \
  94                        "setenv get_cmd tftp; " \
  95                "fi; " \
  96                "if mmc dev ${mmcdev}; then "   \
  97                        "if ${get_cmd} ${update_sd_firmware_filename}; then " \
  98                                "setexpr fw_sz ${filesize} / 0x200; " \
  99                                "setexpr fw_sz ${fw_sz} + 1; "  \
 100                                "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 101                        "fi; "  \
 102                "fi\0" \
 103        "findfdt="\
 104                "if test $board_rev = MX6Q ; then " \
 105                        "setenv fdtprefix imx6q; fi; " \
 106                "if test $board_rev = MX6DL ; then " \
 107                        "setenv fdtprefix imx6dl; fi; " \
 108                "if test $som_rev = V15 ; then " \
 109                        "setenv fdtsuffix -som-v15; fi; " \
 110                "if test $board_name = HUMMINGBOARD2 ; then " \
 111                        "setenv fdtfile ${fdtprefix}-hummingboard2${fdtsuffix}.dtb; fi; " \
 112                "if test $board_name = HUMMINGBOARD ; then " \
 113                        "setenv fdtfile ${fdtprefix}-hummingboard${fdtsuffix}.dtb; fi; " \
 114                "if test $board_name = CUBOXI ; then " \
 115                        "setenv fdtfile ${fdtprefix}-cubox-i${fdtsuffix}.dtb; fi; " \
 116                "if test $fdtfile = undefined; then " \
 117                        "echo WARNING: Could not determine dtb to use; fi; \0" \
 118        BOOTENV
 119
 120#define BOOT_TARGET_DEVICES(func) \
 121        func(MMC, mmc, 0) \
 122        func(SATA, sata, 0) \
 123        func(USB, usb, 0) \
 124        func(PXE, pxe, na) \
 125        func(DHCP, dhcp, na)
 126
 127#include <config_distro_bootcmd.h>
 128
 129#else
 130#define CONFIG_EXTRA_ENV_SETTINGS
 131#endif /* CONFIG_SPL_BUILD */
 132
 133/* Physical Memory Map */
 134#define CONFIG_NR_DRAM_BANKS           1
 135#define CONFIG_SYS_SDRAM_BASE          MMDC0_ARB_BASE_ADDR
 136#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 137#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 138
 139#define CONFIG_SYS_INIT_SP_OFFSET \
 140        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 141#define CONFIG_SYS_INIT_SP_ADDR \
 142        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 143
 144/* Environment organization */
 145#define CONFIG_ENV_SIZE                 (8 * 1024)
 146#define CONFIG_ENV_OFFSET               (8 * 64 * 1024)
 147
 148#endif                         /* __MX6CUBOXI_CONFIG_H */
 149