LXR uboot/include/configs/gw

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * Copyright (C) 2013 Gateworks Corporation
   4 */
   5
   6#ifndef __CONFIG_H
   7#define __CONFIG_H
   8
   9/* SPL */
  10/* Location in NAND to read U-Boot from */
  11#define CONFIG_SYS_NAND_U_BOOT_OFFS     (14 * SZ_1M)
  12
  13/* Falcon Mode */
  14#define CONFIG_SYS_SPL_ARGS_ADDR        0x18000000
  15
  16/* Falcon Mode - NAND support: args@17MB kernel@18MB */
  17#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M)
  18
  19/* Falcon Mode - MMC support: args@1MB kernel@2MB */
  20#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0x800   /* 1MB */
  21#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  (CONFIG_CMD_SPL_WRITE_SIZE / 512)
  22#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000  /* 2MB */
  23
  24#include "imx6_spl.h"                  /* common IMX6 SPL configuration */
  25#include "mx6_common.h"
  26
  27#define CONFIG_MACH_TYPE        4520   /* Gateworks Ventana Platform */
  28
  29/* Serial ATAG */
  30#define CONFIG_SERIAL_TAG
  31
  32/* Size of malloc() pool */
  33#define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  34
  35/* Init Functions */
  36
  37/* Driver Model */
  38#ifndef CONFIG_SPL_BUILD
  39#define CONFIG_DM_GPIO
  40#define CONFIG_DM_THERMAL
  41#endif
  42
  43/* Thermal */
  44#define CONFIG_IMX_THERMAL
  45
  46/* Serial */
  47#define CONFIG_MXC_UART
  48#define CONFIG_MXC_UART_BASE           UART2_BASE
  49
  50#ifdef CONFIG_SPI_FLASH
  51
  52/* SPI */
  53#ifdef CONFIG_CMD_SF
  54  #define CONFIG_SPI_FLASH_MTD
  55  #define CONFIG_SPI_FLASH_BAR
  56  #define CONFIG_SF_DEFAULT_BUS              0
  57  #define CONFIG_SF_DEFAULT_CS               0
  58                                             /* GPIO 3-19 (21248) */
  59  #define CONFIG_SF_DEFAULT_SPEED            30000000
  60  #define CONFIG_SF_DEFAULT_MODE             (SPI_MODE_0)
  61#endif
  62
  63#elif defined(CONFIG_SPL_NAND_SUPPORT)
  64/* Enable NAND support */
  65#ifdef CONFIG_CMD_NAND
  66  #define CONFIG_SYS_MAX_NAND_DEVICE    1
  67  #define CONFIG_SYS_NAND_BASE          0x40000000
  68  #define CONFIG_SYS_NAND_5_ADDR_CYCLE
  69  #define CONFIG_SYS_NAND_ONFI_DETECTION
  70
  71  /* DMA stuff, needed for GPMI/MXS NAND support */
  72#endif
  73
  74#endif /* CONFIG_SPI_FLASH */
  75
  76/* I2C Configs */
  77#define CONFIG_SYS_I2C
  78#define CONFIG_SYS_I2C_MXC
  79#define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  80#define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  81#define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  82#define CONFIG_SYS_I2C_SPEED            100000
  83#define CONFIG_I2C_GSC                  0
  84#define CONFIG_I2C_EDID
  85
  86/* MMC Configs */
  87#define CONFIG_SYS_FSL_ESDHC_ADDR      0
  88
  89/* eMMC Configs */
  90#define CONFIG_SUPPORT_EMMC_BOOT
  91
  92/*
  93 * SATA Configs
  94 */
  95#ifdef CONFIG_CMD_SATA
  96  #define CONFIG_SYS_SATA_MAX_DEVICE    1
  97  #define CONFIG_DWC_AHSATA_PORT_ID     0
  98  #define CONFIG_DWC_AHSATA_BASE_ADDR   SATA_ARB_BASE_ADDR
  99  #define CONFIG_LBA48
 100#endif
 101
 102/*
 103 * PCI express
 104 */
 105#ifdef CONFIG_CMD_PCI
 106#define CONFIG_PCI_SCAN_SHOW
 107#define CONFIG_PCI_FIXUP_DEV
 108#define CONFIG_PCIE_IMX
 109#endif
 110
 111/*
 112 * PMIC
 113 */
 114#define CONFIG_POWER
 115#define CONFIG_POWER_I2C
 116#define CONFIG_POWER_PFUZE100
 117#define CONFIG_POWER_PFUZE100_I2C_ADDR  0x08
 118#define CONFIG_POWER_LTC3676
 119#define CONFIG_POWER_LTC3676_I2C_ADDR  0x3c
 120
 121/* Various command support */
 122#define CONFIG_CMD_UNZIP         /* gzwrite */
 123
 124/* Ethernet support */
 125#define CONFIG_FEC_MXC
 126#define IMX_FEC_BASE             ENET_BASE_ADDR
 127#define CONFIG_FEC_XCV_TYPE      RGMII
 128#define CONFIG_FEC_MXC_PHYADDR   0
 129#define CONFIG_ARP_TIMEOUT       200UL
 130
 131/* USB Configs */
 132#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 133#define CONFIG_EHCI_HCD_INIT_AFTER_RESET  /* For OTG port */
 134#define CONFIG_MXC_USB_PORTSC     (PORT_PTS_UTMI | PORT_PTS_PTW)
 135#define CONFIG_MXC_USB_FLAGS      0
 136#define CONFIG_USBD_HS
 137#define CONFIG_NETCONSOLE
 138
 139/* Framebuffer and LCD */
 140#define CONFIG_VIDEO_IPUV3
 141#define CONFIG_VIDEO_LOGO
 142#define CONFIG_IMX_HDMI
 143#define CONFIG_IMX_VIDEO_SKIP
 144#define CONFIG_VIDEO_BMP_LOGO
 145#define CONFIG_SPLASH_SCREEN_ALIGN
 146#define CONFIG_HIDE_LOGO_VERSION  /* Custom config to hide U-boot version */
 147
 148/* Miscellaneous configurable options */
 149#define CONFIG_HWCONFIG
 150#define CONFIG_PREBOOT
 151
 152/* Memory configuration */
 153#define CONFIG_SYS_MEMTEST_START       0x10000000
 154#define CONFIG_SYS_MEMTEST_END         0x10010000
 155#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 156
 157/* Physical Memory Map */
 158#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 159#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 160#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 161#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 162
 163#define CONFIG_SYS_INIT_SP_OFFSET \
 164        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 165#define CONFIG_SYS_INIT_SP_ADDR \
 166        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 167
 168/*
 169 * MTD Command for mtdparts
 170 */
 171
 172/* Persistent Environment Config */
 173#if defined(CONFIG_ENV_IS_IN_MMC)
 174  #define CONFIG_SYS_MMC_ENV_DEV         0
 175  #define CONFIG_SYS_MMC_ENV_PART        1
 176  #define CONFIG_ENV_OFFSET              (709 * SZ_1K)
 177  #define CONFIG_ENV_SIZE                (128 * SZ_1K)
 178  #define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + (128 * SZ_1K))
 179#elif defined(CONFIG_ENV_IS_IN_NAND)
 180  #define CONFIG_ENV_OFFSET              (16 * SZ_1M)
 181  #define CONFIG_ENV_SECT_SIZE           (128 * SZ_1K)
 182  #define CONFIG_ENV_SIZE                CONFIG_ENV_SECT_SIZE
 183  #define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + (512 * SZ_1K))
 184  #define CONFIG_ENV_SIZE_REDUND         CONFIG_ENV_SIZE
 185#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 186  #define CONFIG_ENV_OFFSET             (512 * SZ_1K)
 187  #define CONFIG_ENV_SECT_SIZE          (64 * SZ_1K)
 188  #define CONFIG_ENV_SIZE               (8 * SZ_1K)
 189  #define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
 190  #define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
 191  #define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
 192  #define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
 193#endif
 194
 195/* Environment */
 196#define CONFIG_IPADDR             192.168.1.1
 197#define CONFIG_SERVERIP           192.168.1.146
 198
 199#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 200        "pcidisable=1\0" \
 201        "splashpos=m,m\0" \
 202        "usb_pgood_delay=2000\0" \
 203        "console=ttymxc1\0" \
 204        "bootdevs=usb mmc sata flash\0" \
 205        "hwconfig=_UNKNOWN_\0" \
 206        "video=\0" \
 207        \
 208        "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
 209        "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
 210        "disk=0\0" \
 211        "part=1\0" \
 212        \
 213        "fdt_high=0xffffffff\0" \
 214        "fdt_addr=0x18000000\0" \
 215        "initrd_high=0xffffffff\0" \
 216        "fixfdt=" \
 217                "fdt addr ${fdt_addr}\0" \
 218        "bootdir=boot\0" \
 219        "loadfdt=" \
 220                "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \
 221                        "echo Loaded DTB from ${bootdir}/${fdt_file}; " \
 222                        "run fixfdt; " \
 223                "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \
 224                        "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \
 225                        "run fixfdt; " \
 226                "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \
 227                        "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \
 228                        "run fixfdt; " \
 229                "fi\0" \
 230        \
 231        "fs=ext4\0" \
 232        "script=6x_bootscript-ventana\0" \
 233        "loadscript=" \
 234                "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \
 235                        "source ${loadaddr}; " \
 236                "fi\0" \
 237        \
 238        "uimage=uImage\0" \
 239        "mmc_root=mmcblk0p1\0" \
 240        "mmc_boot=" \
 241                "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \
 242                "mmc dev ${disk} && mmc rescan && " \
 243                "setenv dtype mmc; run loadscript; " \
 244                "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 245                        "setenv bootargs console=${console},${baudrate} " \
 246                                "root=/dev/${mmc_root} rootfstype=${fs} " \
 247                                "rootwait rw ${video} ${extra}; " \
 248                        "if run loadfdt; then " \
 249                                "bootm ${loadaddr} - ${fdt_addr}; " \
 250                        "else " \
 251                                "bootm; " \
 252                        "fi; " \
 253                "fi\0" \
 254        \
 255        "sata_boot=" \
 256                "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \
 257                "sata init && " \
 258                "setenv dtype sata; run loadscript; " \
 259                "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 260                        "setenv bootargs console=${console},${baudrate} " \
 261                                "root=/dev/sda1 rootfstype=${fs} " \
 262                                "rootwait rw ${video} ${extra}; " \
 263                        "if run loadfdt; then " \
 264                                "bootm ${loadaddr} - ${fdt_addr}; " \
 265                        "else " \
 266                                "bootm; " \
 267                        "fi; " \
 268                "fi\0" \
 269        "usb_boot=" \
 270                "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \
 271                "usb start && usb dev ${disk} && " \
 272                "setenv dtype usb; run loadscript; " \
 273                "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 274                        "setenv bootargs console=${console},${baudrate} " \
 275                                "root=/dev/sda1 rootfstype=${fs} " \
 276                                "rootwait rw ${video} ${extra}; " \
 277                        "if run loadfdt; then " \
 278                                "bootm ${loadaddr} - ${fdt_addr}; " \
 279                        "else " \
 280                                "bootm; " \
 281                        "fi; " \
 282                "fi\0"
 283
 284#ifdef CONFIG_SPI_FLASH
 285        #define CONFIG_EXTRA_ENV_SETTINGS \
 286        CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 287        "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
 288        "image_uboot=ventana/u-boot_spi.imx\0" \
 289        \
 290        "spi_koffset=0x90000\0" \
 291        "spi_klen=0x200000\0" \
 292        \
 293        "spi_updateuboot=echo Updating uboot from " \
 294                "${serverip}:${image_uboot}...; " \
 295                "tftpboot ${loadaddr} ${image_uboot} && " \
 296                "sf probe && sf erase 0 80000 && " \
 297                        "sf write ${loadaddr} 400 ${filesize}\0" \
 298        "spi_update=echo Updating OS from ${serverip}:${image_os} " \
 299                "to ${spi_koffset} ...; " \
 300                "tftp ${loadaddr} ${image_os} && " \
 301                "sf probe && " \
 302                "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
 303        \
 304        "flash_boot=" \
 305                "if sf probe && " \
 306                "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
 307                        "setenv bootargs console=${console},${baudrate} " \
 308                                "root=/dev/mtdblock3 " \
 309                                "rootfstype=squashfs,jffs2 " \
 310                                "${video} ${extra}; " \
 311                        "bootm; " \
 312                "fi\0"
 313#else
 314        #define CONFIG_EXTRA_ENV_SETTINGS \
 315        CONFIG_EXTRA_ENV_SETTINGS_COMMON \
 316        \
 317        "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
 318        "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
 319                "tftp ${loadaddr} ${image_rootfs} && " \
 320                "nand erase.part rootfs && " \
 321                "nand write ${loadaddr} rootfs ${filesize}\0" \
 322        \
 323        "flash_boot=" \
 324                "setenv fsload 'ubifsload'; " \
 325                "ubi part rootfs; " \
 326                "if ubi check boot; then " \
 327                        "ubifsmount ubi0:boot; " \
 328                        "setenv root ubi0:rootfs ubi.mtd=2 " \
 329                                "rootfstype=squashfs,ubifs; " \
 330                        "setenv bootdir; " \
 331                "elif ubi check rootfs; then " \
 332                        "ubifsmount ubi0:rootfs; " \
 333                        "setenv root ubi0:rootfs ubi.mtd=2 " \
 334                                "rootfstype=ubifs; " \
 335                "fi; " \
 336                "setenv dtype nand; run loadscript; " \
 337                "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
 338                        "setenv bootargs console=${console},${baudrate} " \
 339                                "root=${root} ${video} ${extra}; " \
 340                        "if run loadfdt; then " \
 341                                "ubifsumount; " \
 342                                "bootm ${loadaddr} - ${fdt_addr}; " \
 343                        "else " \
 344                                "ubifsumount; bootm; " \
 345                        "fi; " \
 346                "fi\0"
 347#endif
 348
 349#define CONFIG_BOOTCOMMAND \
 350        "for btype in ${bootdevs}; do " \
 351                "echo; echo Attempting ${btype} boot...; " \
 352                "if run ${btype}_boot; then; fi; " \
 353        "done"
 354
 355#endif                         /* __CONFIG_H */
 356