LXR uboot/include/configs/ls1012a

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * Copyright 2016 Freescale Semiconductor
   4 */
   5
   6#ifndef __LS1012A_COMMON_H
   7#define __LS1012A_COMMON_H
   8
   9#define CONFIG_FSL_LAYERSCAPE
  10#define CONFIG_GICV2
  11
  12#include <asm/arch/config.h>
  13#include <asm/arch/stream_id_lsch2.h>
  14
  15#define CONFIG_SYS_CLK_FREQ             125000000
  16
  17#define CONFIG_SKIP_LOWLEVEL_INIT
  18
  19#ifdef CONFIG_TFABOOT
  20#define CONFIG_SYS_INIT_SP_ADDR                CONFIG_SYS_TEXT_BASE
  21#else
  22#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  23#endif
  24#define CONFIG_SYS_LOAD_ADDR    (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
  25
  26#define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  27#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  28#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  29#define CONFIG_SYS_DDR_BLOCK2_BASE     0x880000000ULL
  30
  31/* Generic Timer Definitions */
  32#define COUNTER_FREQUENCY               25000000        /* 25MHz */
  33
  34/* CSU */
  35#define CONFIG_LAYERSCAPE_NS_ACCESS
  36
  37/* Size of malloc() pool */
  38#define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 128 * 1024)
  39
  40/*SPI device */
  41#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_TFABOOT)
  42#define CONFIG_SYS_QE_FW_IN_SPIFLASH
  43#define CONFIG_SYS_FMAN_FW_ADDR         0x400d0000
  44#define CONFIG_ENV_SPI_BUS              0
  45#define CONFIG_ENV_SPI_CS               0
  46#define CONFIG_ENV_SPI_MAX_HZ           1000000
  47#define CONFIG_ENV_SPI_MODE             0x03
  48#define CONFIG_SPI_FLASH_SPANSION
  49#define CONFIG_FSL_SPI_INTERFACE
  50#define CONFIG_SF_DATAFLASH
  51
  52#define CONFIG_FSL_QSPI
  53#define QSPI0_AMBA_BASE         0x40000000
  54#define CONFIG_SPI_FLASH_SPANSION
  55
  56#define FSL_QSPI_FLASH_SIZE             SZ_64M
  57#define FSL_QSPI_FLASH_NUM              2
  58
  59/*
  60 * Environment
  61 */
  62#define CONFIG_ENV_OVERWRITE
  63
  64#define CONFIG_ENV_SIZE                 0x40000          /* 256KB */
  65#ifdef CONFIG_TFABOOT
  66#define CONFIG_ENV_OFFSET               0x500000        /* 5MB */
  67#else
  68#define CONFIG_ENV_OFFSET               0x300000        /* 3MB */
  69#endif
  70#define CONFIG_ENV_SECT_SIZE            0x40000
  71#endif
  72
  73/* SATA */
  74#define CONFIG_SCSI_AHCI_PLAT
  75
  76#define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  77
  78#define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  79#define CONFIG_SYS_SCSI_MAX_LUN                 1
  80#define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  81                                                CONFIG_SYS_SCSI_MAX_LUN)
  82
  83/* I2C */
  84#define CONFIG_SYS_I2C
  85
  86#define CONFIG_SYS_NS16550_SERIAL
  87#define CONFIG_SYS_NS16550_REG_SIZE     1
  88#define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  89
  90#define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  91
  92#define CONFIG_SYS_HZ                   1000
  93
  94#define CONFIG_HWCONFIG
  95#define HWCONFIG_BUFFER_SIZE            128
  96
  97#ifndef CONFIG_SPL_BUILD
  98#define BOOT_TARGET_DEVICES(func) \
  99        func(SCSI, scsi, 0) \
 100        func(MMC, mmc, 0) \
 101        func(USB, usb, 0)
 102#include <config_distro_bootcmd.h>
 103#endif
 104
 105/* Initial environment variables */
 106#define CONFIG_EXTRA_ENV_SETTINGS               \
 107        "verify=no\0"                           \
 108        "loadaddr=0x80100000\0"                 \
 109        "kernel_addr=0x100000\0"                \
 110        "fdt_high=0xffffffffffffffff\0"         \
 111        "initrd_high=0xffffffffffffffff\0"      \
 112        "kernel_start=0x1000000\0"              \
 113        "kernel_load=0xa0000000\0"              \
 114        "kernel_size=0x2800000\0"               \
 115
 116#undef CONFIG_BOOTCOMMAND
 117#ifdef CONFIG_TFABOOT
 118#define QSPI_NOR_BOOTCOMMAND    "pfe stop; sf probe 0:0; sf read $kernel_load "\
 119                                "$kernel_start $kernel_size && "\
 120                                "bootm $kernel_load"
 121#else
 122#define CONFIG_BOOTCOMMAND      "pfe stop; sf probe 0:0; sf read $kernel_load "\
 123                                "$kernel_start $kernel_size && "\
 124                                "bootm $kernel_load"
 125#endif
 126
 127/* Monitor Command Prompt */
 128#define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 129#define CONFIG_SYS_MAXARGS              64      /* max command args */
 130
 131#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 132
 133#include <asm/arch/soc.h>
 134
 135#endif /* __LS1012A_COMMON_H */
 136