// SPDX-License-Identifier: GPL-2.0
/*
 * Based on m25p80.c, by Mike Lavender (mike@steroidmicros.com), with
 * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c
 *
 * Copyright (C) 2005, Intec Automation Inc.
 * Copyright (C) 2014, Freescale Semiconductor, Inc.
 *
 * Synced from Linux v4.19
 */

#include <common.h>
#include <linux/err.h>
#include <linux/errno.h>
#include <linux/log2.h>
#include <linux/math64.h>
#include <linux/sizes.h>

#include <linux/mtd/mtd.h>
#include <linux/mtd/spi-nor.h>
#include <spi-mem.h>
#include <spi.h>

#include "sf_internal.h"

/* Define max times to check status register before we give up. */

/*
 * For everything but full-chip erase; probably could be much smaller, but kept
 * around for safety for now
 */

#define HZ                                      CONFIG_SYS_HZ

#define DEFAULT_READY_WAIT_JIFFIES              (40UL * HZ)

static int spi_nor_read_write_reg(struct spi_nor *nor, struct spi_mem_op
                *op, void *buf)
{
        if (op->data.dir == SPI_MEM_DATA_IN)
                op->data.buf.in = buf;
        else
                op->data.buf.out = buf;
        return spi_mem_exec_op(nor->spi, op);
}

static int spi_nor_read_reg(struct spi_nor *nor, u8 code, u8 *val, int len)
{
        struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(code, 1),
                                          SPI_MEM_OP_NO_ADDR,
                                          SPI_MEM_OP_NO_DUMMY,
                                          SPI_MEM_OP_DATA_IN(len, NULL, 1));
        int ret;

        ret = spi_nor_read_write_reg(nor, &op, val);
        if (ret < 0)
                dev_dbg(&flash->spimem->spi->dev, "error %d reading %x\n", ret,
                        code);

        return ret;
}

static int spi_nor_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
{
        struct spi_mem_op op = SPI_MEM_OP(SPI_MEM_OP_CMD(opcode, 1),
                                          SPI_MEM_OP_NO_ADDR,
                                          SPI_MEM_OP_NO_DUMMY,
                                          SPI_MEM_OP_DATA_OUT(len, NULL, 1));

        return spi_nor_read_write_reg(nor, &op, buf);
}

static ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
                                 u_char *buf)
{
        struct spi_mem_op op =
                        SPI_MEM_OP(SPI_MEM_OP_CMD(nor->read_opcode, 1),
                                   SPI_MEM_OP_ADDR(nor->addr_width, from, 1),
                                   SPI_MEM_OP_DUMMY(nor->read_dummy, 1),
                                   SPI_MEM_OP_DATA_IN(len, buf, 1));
        size_t remaining = len;
        int ret;

        /* get transfer protocols. */
        op.cmd.buswidth = spi_nor_get_protocol_inst_nbits(nor->read_proto);
        op.addr.buswidth = spi_nor_get_protocol_addr_nbits(nor->read_proto);
        op.dummy.buswidth = op.addr.buswidth;
        op.data.buswidth = spi_nor_get_protocol_data_nbits(nor->read_proto);

        /* convert the dummy cycles to the number of bytes */
        op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;

        while (remaining) {
                op.data.nbytes = remaining < UINT_MAX ? remaining : UINT_MAX;
                ret = spi_mem_adjust_op_size(nor->spi, &op);
                if (ret)
                        return ret;

                ret = spi_mem_exec_op(nor->spi, &op);
                if (ret)
                        return ret;

                op.addr.val += op.data.nbytes;
                remaining -= op.data.nbytes;
                op.data.buf.in += op.data.nbytes;
        }

        return len;
}

#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
/*
 * Read configuration register, returning its value in the
 * location. Return the configuration register value.
 * Returns negative if error occurred.
 */
static int read_cr(struct spi_nor *nor)
{
        int ret;
        u8 val;

        ret = spi_nor_read_reg(nor, SPINOR_OP_RDCR, &val, 1);
        if (ret < 0) {
                dev_dbg(nor->dev, "error %d reading CR\n", ret);
                return ret;
        }

        return val;
}
#endif

/*
 * Write status register 1 byte
 * Returns negative if error occurred.
 */
static inline int write_sr(struct spi_nor *nor, u8 val)
{
        nor->cmd_buf[0] = val;
        return spi_nor_write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1);
}

/*
 * Set write enable latch with Write Enable command.
 * Returns negative if error occurred.
 */
static inline int write_enable(struct spi_nor *nor)
{
        return spi_nor_write_reg(nor, SPINOR_OP_WREN, NULL, 0);
}

/*
 * Send write disable instruction to the chip.
 */
static inline int write_disable(struct spi_nor *nor)
{
        return spi_nor_write_reg(nor, SPINOR_OP_WRDI, NULL, 0);
}

static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
{
        return mtd->priv;
}

static u8 spi_nor_convert_opcode(u8 opcode, const u8 table[][2], size_t size)
{
        size_t i;

        for (i = 0; i < size; i++)
                if (table[i][0] == opcode)
                        return table[i][1];

        /* No conversion found, keep input op code. */
        return opcode;
}

static inline u8 spi_nor_convert_3to4_read(u8 opcode)
{
        static const u8 spi_nor_3to4_read[][2] = {
                { SPINOR_OP_READ,       SPINOR_OP_READ_4B },
                { SPINOR_OP_READ_FAST,  SPINOR_OP_READ_FAST_4B },
                { SPINOR_OP_READ_1_1_2, SPINOR_OP_READ_1_1_2_4B },
                { SPINOR_OP_READ_1_2_2, SPINOR_OP_READ_1_2_2_4B },
                { SPINOR_OP_READ_1_1_4, SPINOR_OP_READ_1_1_4_4B },
                { SPINOR_OP_READ_1_4_4, SPINOR_OP_READ_1_4_4_4B },
        };

        return spi_nor_convert_opcode(opcode, spi_nor_3to4_read,
                                      ARRAY_SIZE(spi_nor_3to4_read));
}

static void spi_nor_set_4byte_opcodes(struct spi_nor *nor,
                                      const struct flash_info *info)
{
        nor->read_opcode = spi_nor_convert_3to4_read(nor->read_opcode);
}

/* Enable/disable 4-byte addressing mode. */
static inline int set_4byte(struct spi_nor *nor, const struct flash_info *info,
                            int enable)
{
        int status;
        bool need_wren = false;
        u8 cmd;

        switch (JEDEC_MFR(info)) {
        case SNOR_MFR_ST:
        case SNOR_MFR_MICRON:
                /* Some Micron need WREN command; all will accept it */
                need_wren = true;
        case SNOR_MFR_MACRONIX:
        case SNOR_MFR_WINBOND:
                if (need_wren)
                        write_enable(nor);

                cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B;
                status = spi_nor_write_reg(nor, cmd, NULL, 0);
                if (need_wren)
                        write_disable(nor);

                if (!status && !enable &&
                    JEDEC_MFR(info) == SNOR_MFR_WINBOND) {
                        /*
                         * On Winbond W25Q256FV, leaving 4byte mode causes
                         * the Extended Address Register to be set to 1, so all
                         * 3-byte-address reads come from the second 16M.
                         * We must clear the register to enable normal behavior.
                         */
                        write_enable(nor);
                        nor->cmd_buf[0] = 0;
                        spi_nor_write_reg(nor, SPINOR_OP_WREAR,
                                          nor->cmd_buf, 1);
                        write_disable(nor);
                }

                return status;
        default:
                /* Spansion style */
                nor->cmd_buf[0] = enable << 7;
                return spi_nor_write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1);
        }
}

#if defined(CONFIG_SPI_FLASH_SPANSION) ||       \
        defined(CONFIG_SPI_FLASH_WINBOND) ||    \
        defined(CONFIG_SPI_FLASH_MACRONIX)
/*
 * Read the status register, returning its value in the location
 * Return the status register value.
 * Returns negative if error occurred.
 */
static int read_sr(struct spi_nor *nor)
{
        int ret;
        u8 val;

        ret = spi_nor_read_reg(nor, SPINOR_OP_RDSR, &val, 1);
        if (ret < 0) {
                pr_debug("error %d reading SR\n", (int)ret);
                return ret;
        }

        return val;
}

/*
 * Read the flag status register, returning its value in the location
 * Return the status register value.
 * Returns negative if error occurred.
 */
static int read_fsr(struct spi_nor *nor)
{
        int ret;
        u8 val;

        ret = spi_nor_read_reg(nor, SPINOR_OP_RDFSR, &val, 1);
        if (ret < 0) {
                pr_debug("error %d reading FSR\n", ret);
                return ret;
        }

        return val;
}

static int spi_nor_sr_ready(struct spi_nor *nor)
{
        int sr = read_sr(nor);

        if (sr < 0)
                return sr;

        return !(sr & SR_WIP);
}

static int spi_nor_fsr_ready(struct spi_nor *nor)
{
        int fsr = read_fsr(nor);

        if (fsr < 0)
                return fsr;
        return fsr & FSR_READY;
}

static int spi_nor_ready(struct spi_nor *nor)
{
        int sr, fsr;

        sr = spi_nor_sr_ready(nor);
        if (sr < 0)
                return sr;
        fsr = nor->flags & SNOR_F_USE_FSR ? spi_nor_fsr_ready(nor) : 1;
        if (fsr < 0)
                return fsr;
        return sr && fsr;
}

/*
 * Service routine to read status register until ready, or timeout occurs.
 * Returns non-zero if error.
 */
static int spi_nor_wait_till_ready_with_timeout(struct spi_nor *nor,
                                                unsigned long timeout)
{
        unsigned long timebase;
        int ret;

        timebase = get_timer(0);

        while (get_timer(timebase) < timeout) {
                ret = spi_nor_ready(nor);
                if (ret < 0)
                        return ret;
                if (ret)
                        return 0;
        }

        dev_err(nor->dev, "flash operation timed out\n");

        return -ETIMEDOUT;
}

static int spi_nor_wait_till_ready(struct spi_nor *nor)
{
        return spi_nor_wait_till_ready_with_timeout(nor,
                                                    DEFAULT_READY_WAIT_JIFFIES);
}
#endif /* CONFIG_SPI_FLASH_SPANSION */

/*
 * Erase an address range on the nor chip.  The address range may extend
 * one or more erase sectors.  Return an error is there is a problem erasing.
 */
static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr)
{
        return -ENOTSUPP;
}

static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
{
        int                     tmp;
        u8                      id[SPI_NOR_MAX_ID_LEN];
        const struct flash_info *info;

        tmp = spi_nor_read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
        if (tmp < 0) {
                dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
                return ERR_PTR(tmp);
        }

        info = spi_nor_ids;
        for (; info->sector_size != 0; info++) {
                if (info->id_len) {
                        if (!memcmp(info->id, id, info->id_len))
                                return info;
                }
        }
        dev_dbg(nor->dev, "unrecognized JEDEC id bytes: %02x, %02x, %02x\n",
                id[0], id[1], id[2]);
        return ERR_PTR(-ENODEV);
}

static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
                        size_t *retlen, u_char *buf)
{
        struct spi_nor *nor = mtd_to_spi_nor(mtd);
        int ret;

        dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len);

        while (len) {
                loff_t addr = from;

                ret = spi_nor_read_data(nor, addr, len, buf);
                if (ret == 0) {
                        /* We shouldn't see 0-length reads */
                        ret = -EIO;
                        goto read_err;
                }
                if (ret < 0)
                        goto read_err;

                *retlen += ret;
                buf += ret;
                from += ret;
                len -= ret;
        }
        ret = 0;

read_err:
        return ret;
}

/*
 * Write an address range to the nor chip.  Data must be written in
 * FLASH_PAGESIZE chunks.  The address range may be any size provided
 * it is within the physical boundaries.
 */
static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
                         size_t *retlen, const u_char *buf)
{
        return -ENOTSUPP;
}

#ifdef CONFIG_SPI_FLASH_MACRONIX
/**
 * macronix_quad_enable() - set QE bit in Status Register.
 * @nor:        pointer to a 'struct spi_nor'
 *
 * Set the Quad Enable (QE) bit in the Status Register.
 *
 * bit 6 of the Status Register is the QE bit for Macronix like QSPI memories.
 *
 * Return: 0 on success, -errno otherwise.
 */
static int macronix_quad_enable(struct spi_nor *nor)
{
        int ret, val;

        val = read_sr(nor);
        if (val < 0)
                return val;
        if (val & SR_QUAD_EN_MX)
                return 0;

        write_enable(nor);

        write_sr(nor, val | SR_QUAD_EN_MX);

        ret = spi_nor_wait_till_ready(nor);
        if (ret)
                return ret;

        ret = read_sr(nor);
        if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) {
                dev_err(nor->dev, "Macronix Quad bit not set\n");
                return -EINVAL;
        }

        return 0;
}
#endif

#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
/*
 * Write status Register and configuration register with 2 bytes
 * The first byte will be written to the status register, while the
 * second byte will be written to the configuration register.
 * Return negative if error occurred.
 */
static int write_sr_cr(struct spi_nor *nor, u8 *sr_cr)
{
        int ret;

        write_enable(nor);

        ret = spi_nor_write_reg(nor, SPINOR_OP_WRSR, sr_cr, 2);
        if (ret < 0) {
                dev_dbg(nor->dev,
                        "error while writing configuration register\n");
                return -EINVAL;
        }

        ret = spi_nor_wait_till_ready(nor);
        if (ret) {
                dev_dbg(nor->dev,
                        "timeout while writing configuration register\n");
                return ret;
        }

        return 0;
}

/**
 * spansion_read_cr_quad_enable() - set QE bit in Configuration Register.
 * @nor:        pointer to a 'struct spi_nor'
 *
 * Set the Quad Enable (QE) bit in the Configuration Register.
 * This function should be used with QSPI memories supporting the Read
 * Configuration Register (35h) instruction.
 *
 * bit 1 of the Configuration Register is the QE bit for Spansion like QSPI
 * memories.
 *
 * Return: 0 on success, -errno otherwise.
 */
static int spansion_read_cr_quad_enable(struct spi_nor *nor)
{
        u8 sr_cr[2];
        int ret;

        /* Check current Quad Enable bit value. */
        ret = read_cr(nor);
        if (ret < 0) {
                dev_dbg(dev, "error while reading configuration register\n");
                return -EINVAL;
        }

        if (ret & CR_QUAD_EN_SPAN)
                return 0;

        sr_cr[1] = ret | CR_QUAD_EN_SPAN;

        /* Keep the current value of the Status Register. */
        ret = read_sr(nor);
        if (ret < 0) {
                dev_dbg(dev, "error while reading status register\n");
                return -EINVAL;
        }
        sr_cr[0] = ret;

        ret = write_sr_cr(nor, sr_cr);
        if (ret)
                return ret;

        /* Read back and check it. */
        ret = read_cr(nor);
        if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) {
                dev_dbg(nor->dev, "Spansion Quad bit not set\n");
                return -EINVAL;
        }

        return 0;
}
#endif /* CONFIG_SPI_FLASH_SPANSION */

struct spi_nor_read_command {
        u8                      num_mode_clocks;
        u8                      num_wait_states;
        u8                      opcode;
        enum spi_nor_protocol   proto;
};

enum spi_nor_read_command_index {
        SNOR_CMD_READ,
        SNOR_CMD_READ_FAST,

        /* Quad SPI */
        SNOR_CMD_READ_1_1_4,

        SNOR_CMD_READ_MAX
};

struct spi_nor_flash_parameter {
        struct spi_nor_hwcaps           hwcaps;
        struct spi_nor_read_command     reads[SNOR_CMD_READ_MAX];
};

static void
spi_nor_set_read_settings(struct spi_nor_read_command *read,
                          u8 num_mode_clocks,
                          u8 num_wait_states,
                          u8 opcode,
                          enum spi_nor_protocol proto)
{
        read->num_mode_clocks = num_mode_clocks;
        read->num_wait_states = num_wait_states;
        read->opcode = opcode;
        read->proto = proto;
}

static int spi_nor_init_params(struct spi_nor *nor,
                               const struct flash_info *info,
                               struct spi_nor_flash_parameter *params)
{
        /* (Fast) Read settings. */
        params->hwcaps.mask = SNOR_HWCAPS_READ;
        spi_nor_set_read_settings(&params->reads[SNOR_CMD_READ],
                                  0, 0, SPINOR_OP_READ,
                                  SNOR_PROTO_1_1_1);

        if (!(info->flags & SPI_NOR_NO_FR)) {
                params->hwcaps.mask |= SNOR_HWCAPS_READ_FAST;
                spi_nor_set_read_settings(&params->reads[SNOR_CMD_READ_FAST],
                                          0, 8, SPINOR_OP_READ_FAST,
                                          SNOR_PROTO_1_1_1);
        }

        if (info->flags & SPI_NOR_QUAD_READ) {
                params->hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
                spi_nor_set_read_settings(&params->reads[SNOR_CMD_READ_1_1_4],
                                          0, 8, SPINOR_OP_READ_1_1_4,
                                          SNOR_PROTO_1_1_4);
        }

        return 0;
}

static int spi_nor_select_read(struct spi_nor *nor,
                               const struct spi_nor_flash_parameter *params,
                               u32 shared_hwcaps)
{
        int best_match = shared_hwcaps & SNOR_HWCAPS_READ_MASK;
        int cmd;
        const struct spi_nor_read_command *read;

        if (best_match < 0)
                return -EINVAL;

        if (best_match & SNOR_HWCAPS_READ_1_1_4)
                cmd = SNOR_CMD_READ_1_1_4;
        else if (best_match & SNOR_HWCAPS_READ_FAST)
                cmd = SNOR_CMD_READ_FAST;
        else
                cmd = SNOR_CMD_READ;

        read = &params->reads[cmd];
        nor->read_opcode = read->opcode;
        nor->read_proto = read->proto;

        /*
         * In the spi-nor framework, we don't need to make the difference
         * between mode clock cycles and wait state clock cycles.
         * Indeed, the value of the mode clock cycles is used by a QSPI
         * flash memory to know whether it should enter or leave its 0-4-4
         * (Continuous Read / XIP) mode.
         * eXecution In Place is out of the scope of the mtd sub-system.
         * Hence we choose to merge both mode and wait state clock cycles
         * into the so called dummy clock cycles.
         */
        nor->read_dummy = read->num_mode_clocks + read->num_wait_states;
        return 0;
}

static int spi_nor_setup(struct spi_nor *nor, const struct flash_info *info,
                         const struct spi_nor_flash_parameter *params,
                         const struct spi_nor_hwcaps *hwcaps)
{
        u32 shared_mask;
        int err;

        /*
         * Keep only the hardware capabilities supported by both the SPI
         * controller and the SPI flash memory.
         */
        shared_mask = hwcaps->mask & params->hwcaps.mask;

        /* Select the (Fast) Read command. */
        err = spi_nor_select_read(nor, params, shared_mask);
        if (err) {
                dev_dbg(nor->dev,
                        "can't select read settings supported by both the SPI controller and memory.\n");
                return err;
        }

        /* Enable Quad I/O if needed. */
        if (spi_nor_get_protocol_width(nor->read_proto) == 4) {
                switch (JEDEC_MFR(info)) {
#ifdef CONFIG_SPI_FLASH_MACRONIX
                case SNOR_MFR_MACRONIX:
                        err = macronix_quad_enable(nor);
                        break;
#endif
                case SNOR_MFR_ST:
                case SNOR_MFR_MICRON:
                        break;

                default:
#if defined(CONFIG_SPI_FLASH_SPANSION) || defined(CONFIG_SPI_FLASH_WINBOND)
                        /* Kept only for backward compatibility purpose. */
                        err = spansion_read_cr_quad_enable(nor);
#endif
                        break;
                }
        }
        if (err) {
                dev_dbg(nor->dev, "quad mode not supported\n");
                return err;
        }

        return 0;
}

static int spi_nor_init(struct spi_nor *nor)
{
        if (nor->addr_width == 4 &&
            (JEDEC_MFR(nor->info) != SNOR_MFR_SPANSION) &&
            !(nor->info->flags & SPI_NOR_4B_OPCODES)) {
                /*
                 * If the RESET# pin isn't hooked up properly, or the system
                 * otherwise doesn't perform a reset command in the boot
                 * sequence, it's impossible to 100% protect against unexpected
                 * reboots (e.g., crashes). Warn the user (or hopefully, system
                 * designer) that this is bad.
                 */
                if (nor->flags & SNOR_F_BROKEN_RESET)
                        printf("enabling reset hack; may not recover from unexpected reboots\n");
                set_4byte(nor, nor->info, 1);
        }

        return 0;
}

int spi_nor_scan(struct spi_nor *nor)
{
        struct spi_nor_flash_parameter params;
        const struct flash_info *info = NULL;
        struct mtd_info *mtd = &nor->mtd;
        struct spi_nor_hwcaps hwcaps = {
                .mask = SNOR_HWCAPS_READ |
                        SNOR_HWCAPS_READ_FAST
        };
        struct spi_slave *spi = nor->spi;
        int ret;

        /* Reset SPI protocol for all commands. */
        nor->reg_proto = SNOR_PROTO_1_1_1;
        nor->read_proto = SNOR_PROTO_1_1_1;
        nor->write_proto = SNOR_PROTO_1_1_1;

        if (spi->mode & SPI_RX_QUAD)
                hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;

        info = spi_nor_read_id(nor);
        if (IS_ERR_OR_NULL(info))
                return -ENOENT;
        /* Parse the Serial Flash Discoverable Parameters table. */
        ret = spi_nor_init_params(nor, info, &params);
        if (ret)
                return ret;

        mtd->name = "spi-flash";
        mtd->priv = nor;
        mtd->type = MTD_NORFLASH;
        mtd->writesize = 1;
        mtd->flags = MTD_CAP_NORFLASH;
        mtd->size = info->sector_size * info->n_sectors;
        mtd->_erase = spi_nor_erase;
        mtd->_read = spi_nor_read;
        mtd->_write = spi_nor_write;

        nor->size = mtd->size;

        if (info->flags & USE_FSR)
                nor->flags |= SNOR_F_USE_FSR;
        if (info->flags & USE_CLSR)
                nor->flags |= SNOR_F_USE_CLSR;

        if (info->flags & SPI_NOR_NO_FR)
                params.hwcaps.mask &= ~SNOR_HWCAPS_READ_FAST;

        /*
         * Configure the SPI memory:
         * - select op codes for (Fast) Read, Page Program and Sector Erase.
         * - set the number of dummy cycles (mode cycles + wait states).
         * - set the SPI protocols for register and memory accesses.
         * - set the Quad Enable bit if needed (required by SPI x-y-4 protos).
         */
        ret = spi_nor_setup(nor, info, &params, &hwcaps);
        if (ret)
                return ret;

        if (nor->addr_width) {
                /* already configured from SFDP */
        } else if (info->addr_width) {
                nor->addr_width = info->addr_width;
        } else if (mtd->size > 0x1000000) {
                /* enable 4-byte addressing if the device exceeds 16MiB */
                nor->addr_width = 4;
                if (JEDEC_MFR(info) == SNOR_MFR_SPANSION ||
                    info->flags & SPI_NOR_4B_OPCODES)
                        spi_nor_set_4byte_opcodes(nor, info);
        } else {
                nor->addr_width = 3;
        }

        if (nor->addr_width > SPI_NOR_MAX_ADDR_WIDTH) {
                dev_dbg(dev, "address width is too large: %u\n",
                        nor->addr_width);
                return -EINVAL;
        }

        /* Send all the required SPI flash commands to initialize device */
        nor->info = info;
        ret = spi_nor_init(nor);
        if (ret)
                return ret;

        return 0;
}

/* U-Boot specific functions, need to extend MTD to support these */
int spi_flash_cmd_get_sw_write_prot(struct spi_nor *nor)
{
        return -ENOTSUPP;
}