1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * WORK Microwave work_92105 board configuration file 4 * 5 * (C) Copyright 2014 DENX Software Engineering GmbH 6 * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr> 7 */ 8 9#ifndef __CONFIG_WORK_92105_H__ 10#define __CONFIG_WORK_92105_H__ 11 12/* SoC and board defines */ 13#include <linux/sizes.h> 14#include <asm/arch/cpu.h> 15 16/* 17 * Define work_92105 machine type by hand -- done only for compatibility 18 * with original board code 19 */ 20#define CONFIG_MACH_TYPE 736 21 22#if !defined(CONFIG_SPL_BUILD) 23#define CONFIG_SKIP_LOWLEVEL_INIT 24#endif 25 26/* 27 * Memory configurations 28 */ 29#define CONFIG_SYS_MALLOC_LEN SZ_1M 30#define CONFIG_SYS_SDRAM_BASE EMC_DYCS0_BASE 31#define CONFIG_SYS_SDRAM_SIZE SZ_128M 32#define CONFIG_SYS_MEMTEST_START (CONFIG_SYS_SDRAM_BASE + SZ_32K) 33#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_TEXT_BASE - SZ_1M) 34 35#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_32K) 36 37#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_512K \ 38 - GENERATED_GBL_DATA_SIZE) 39 40/* 41 * Serial Driver 42 */ 43#define CONFIG_SYS_LPC32XX_UART 5 /* UART5 - NS16550 */ 44 45/* 46 * Ethernet Driver 47 */ 48 49#define CONFIG_PHY_SMSC 50#define CONFIG_LPC32XX_ETH 51#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN 52/* FIXME: remove "Waiting for PHY auto negotiation to complete..." message */ 53 54/* 55 * I2C driver 56 */ 57 58#define CONFIG_SYS_I2C_LPC32XX 59#define CONFIG_SYS_I2C 60#define CONFIG_SYS_I2C_SPEED 350000 61 62/* 63 * I2C EEPROM 64 */ 65 66#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56 67#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 68 69/* 70 * I2C RTC 71 */ 72 73#define CONFIG_RTC_DS1374 74 75/* 76 * U-Boot General Configurations 77 */ 78#define CONFIG_SYS_CBSIZE 1024 79#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 80 81/* 82 * NAND chip timings for FIXME: which one? 83 */ 84 85#define CONFIG_LPC32XX_NAND_MLC_TCEA_DELAY 333333333 86#define CONFIG_LPC32XX_NAND_MLC_BUSY_DELAY 10000000 87#define CONFIG_LPC32XX_NAND_MLC_NAND_TA 18181818 88#define CONFIG_LPC32XX_NAND_MLC_RD_HIGH 31250000 89#define CONFIG_LPC32XX_NAND_MLC_RD_LOW 45454545 90#define CONFIG_LPC32XX_NAND_MLC_WR_HIGH 40000000 91#define CONFIG_LPC32XX_NAND_MLC_WR_LOW 83333333 92 93/* 94 * NAND 95 */ 96 97/* driver configuration */ 98#define CONFIG_SYS_NAND_SELF_INIT 99#define CONFIG_SYS_MAX_NAND_DEVICE 1 100#define CONFIG_SYS_MAX_NAND_CHIPS 1 101#define CONFIG_SYS_NAND_BASE MLC_NAND_BASE 102#define CONFIG_NAND_LPC32XX_MLC 103 104/* 105 * GPIO 106 */ 107 108#define CONFIG_LPC32XX_GPIO 109 110/* 111 * SSP/SPI/DISPLAY 112 */ 113 114#define CONFIG_LPC32XX_SSP_TIMEOUT 100000 115/* 116 * Environment 117 */ 118 119#define CONFIG_ENV_SIZE 0x00020000 120#define CONFIG_ENV_OFFSET 0x00100000 121#define CONFIG_ENV_OFFSET_REDUND 0x00120000 122#define CONFIG_ENV_ADDR 0x80000100 123 124/* 125 * Boot Linux 126 */ 127#define CONFIG_CMDLINE_TAG 128#define CONFIG_SETUP_MEMORY_TAGS 129#define CONFIG_INITRD_TAG 130 131#define CONFIG_BOOTFILE "uImage" 132#define CONFIG_LOADADDR 0x80008000 133 134/* 135 * SPL 136 */ 137 138/* SPL will be executed at offset 0 */ 139/* SPL will use SRAM as stack */ 140#define CONFIG_SPL_STACK 0x0000FFF8 141/* Use the framework and generic lib */ 142/* SPL will use serial */ 143/* SPL will load U-Boot from NAND offset 0x40000 */ 144#define CONFIG_SPL_NAND_DRIVERS 145#define CONFIG_SPL_NAND_BASE 146#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000 147#define CONFIG_SPL_PAD_TO 0x20000 148/* U-Boot will be 0x40000 bytes, loaded and run at CONFIG_SYS_TEXT_BASE */ 149#define CONFIG_SYS_MONITOR_LEN 0x40000 /* actually, MAX size */ 150#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE 151#define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE 152 153/* 154 * Include SoC specific configuration 155 */ 156#include <asm/arch/config.h> 157 158#endif /* __CONFIG_WORK_92105_H__*/ 159