LXR uboot/include/configs/lx2160ardb.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * Copyright 2018 NXP
   4 */
   5
   6#ifndef __LX2_RDB_H
   7#define __LX2_RDB_H
   8
   9#include "lx2160a_common.h"
  10
  11/* Qixis */
  12#define QIXIS_XMAP_MASK                 0x07
  13#define QIXIS_XMAP_SHIFT                5
  14#define QIXIS_RST_CTL_RESET_EN          0x30
  15#define QIXIS_LBMAP_DFLTBANK            0x00
  16#define QIXIS_LBMAP_ALTBANK             0x20
  17#define QIXIS_LBMAP_QSPI                0x00
  18#define QIXIS_RCW_SRC_QSPI              0xff
  19#define QIXIS_RST_CTL_RESET             0x31
  20#define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
  21#define QIXIS_RCFG_CTL_RECONFIG_START   0x21
  22#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
  23#define QIXIS_LBMAP_MASK                0x0f
  24#define QIXIS_LBMAP_SD
  25#define QIXIS_RCW_SRC_SD           0x08
  26#define NON_EXTENDED_DUTCFG
  27
  28/* VID */
  29
  30#define I2C_MUX_CH_VOL_MONITOR          0xA
  31/* Voltage monitor on channel 2*/
  32#define I2C_VOL_MONITOR_ADDR            0x63
  33#define I2C_VOL_MONITOR_BUS_V_OFFSET    0x2
  34#define I2C_VOL_MONITOR_BUS_V_OVF       0x1
  35#define I2C_VOL_MONITOR_BUS_V_SHIFT     3
  36#define CONFIG_VID_FLS_ENV              "lx2160ardb_vdd_mv"
  37#define CONFIG_VID
  38
  39/* The lowest and highest voltage allowed*/
  40#define VDD_MV_MIN                      775
  41#define VDD_MV_MAX                      855
  42
  43/* PM Bus commands code for LTC3882*/
  44#define PMBUS_CMD_PAGE                  0x0
  45#define PMBUS_CMD_READ_VOUT             0x8B
  46#define PMBUS_CMD_PAGE_PLUS_WRITE       0x05
  47#define PMBUS_CMD_VOUT_COMMAND          0x21
  48#define PWM_CHANNEL0                    0x0
  49
  50#define CONFIG_VOL_MONITOR_LTC3882_SET
  51#define CONFIG_VOL_MONITOR_LTC3882_READ
  52
  53/* RTC */
  54#define CONFIG_SYS_RTC_BUS_NUM          4
  55
  56/* MAC/PHY configuration */
  57#if defined(CONFIG_FSL_MC_ENET)
  58#define CONFIG_MII
  59#define CONFIG_ETHPRIME         "DPMAC1@xgmii"
  60
  61#define AQR107_PHY_ADDR1        0x04
  62#define AQR107_PHY_ADDR2        0x05
  63#define AQR107_IRQ_MASK         0x0C
  64
  65#define CORTINA_NO_FW_UPLOAD
  66#define CORTINA_PHY_ADDR1       0x0
  67#define INPHI_PHY_ADDR1         0x0
  68
  69#define RGMII_PHY_ADDR1         0x01
  70#define RGMII_PHY_ADDR2         0x02
  71
  72#endif
  73
  74/* EMC2305 */
  75#define I2C_MUX_CH_EMC2305              0x09
  76#define I2C_EMC2305_ADDR                0x4D
  77#define I2C_EMC2305_CMD         0x40
  78#define I2C_EMC2305_PWM         0x80
  79
  80/* EEPROM */
  81#define CONFIG_ID_EEPROM
  82#define CONFIG_SYS_I2C_EEPROM_NXID
  83#define CONFIG_SYS_EEPROM_BUS_NUM                  0
  84#define CONFIG_SYS_I2C_EEPROM_ADDR                 0x57
  85#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN      1
  86#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     3
  87#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
  88
  89/* Initial environment variables */
  90#define CONFIG_EXTRA_ENV_SETTINGS               \
  91        EXTRA_ENV_SETTINGS                      \
  92        "lx2160ardb_vdd_mv=800\0"               \
  93        "BOARD=lx2160ardb\0"                    \
  94        "xspi_bootcmd=echo Trying load from flexspi..;"         \
  95                "sf probe 0:0 && sf read $load_addr "           \
  96                "$kernel_start $kernel_size ; env exists secureboot &&" \
  97                "sf read $kernelheader_addr_r $kernelheader_start "     \
  98                "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
  99                " bootm $load_addr#$BOARD\0"                    \
 100        "sd_bootcmd=echo Trying load from sd card..;"           \
 101                "mmcinfo; mmc read $load_addr "                 \
 102                "$kernel_addr_sd $kernel_size_sd ;"             \
 103                "env exists secureboot && mmc read $kernelheader_addr_r "\
 104                "$kernelhdr_addr_sd $kernelhdr_size_sd "        \
 105                " && esbc_validate ${kernelheader_addr_r};"     \
 106                "bootm $load_addr#$BOARD\0"
 107
 108#include <asm/fsl_secure_boot.h>
 109
 110#endif /* __LX2_RDB_H */
 111