LXR uboot/arch/arm/mach-zynqmp/Kconfig

   1if ARCH_ZYNQMP
   2
   3config SPL_FS_FAT
   4        default y
   5
   6config SPL_LIBCOMMON_SUPPORT
   7        default y
   8
   9config SPL_LIBDISK_SUPPORT
  10        default y
  11
  12config SPL_LIBGENERIC_SUPPORT
  13        default y
  14
  15config SPL_MMC_SUPPORT
  16        default y if MMC_SDHCI_ZYNQ
  17
  18config SPL_SERIAL_SUPPORT
  19        default y
  20
  21config SPL_SPI_FLASH_SUPPORT
  22        default y if ZYNQ_QSPI
  23
  24config SPL_SPI_SUPPORT
  25        default y if ZYNQ_QSPI
  26
  27config SYS_BOARD
  28        default "zynqmp"
  29
  30config SYS_VENDOR
  31        string "Vendor name"
  32        default "xilinx"
  33
  34config SYS_SOC
  35        default "zynqmp"
  36
  37config SYS_CONFIG_NAME
  38        string "Board configuration name"
  39        default "xilinx_zynqmp"
  40        help
  41          This option contains information about board configuration name.
  42          Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header
  43          will be used for board configuration.
  44
  45config SYS_MEM_RSVD_FOR_MMU
  46        bool "Reserve memory for MMU Table"
  47        help
  48          If defined this option is used to setup different space for
  49          MMU table than the one which will be allocated during
  50          relocation.
  51
  52config BOOT_INIT_FILE
  53        string "boot.bin init register filename"
  54        depends on SPL
  55        default ""
  56        help
  57          Add register writes to boot.bin format (max 256 pairs).
  58          Expect a table of register-value pairs, e.g. "0x12345678 0x4321"
  59
  60config PMUFW_INIT_FILE
  61        string "PMU firmware"
  62        depends on SPL
  63        default ""
  64        help
  65          Include external PMUFW (Platform Management Unit FirmWare) to
  66          a Xilinx bootable image (boot.bin).
  67
  68config ZYNQMP_SPL_PM_CFG_OBJ_FILE
  69        string "PMU firmware configuration object to load at runtime by SPL"
  70        depends on SPL
  71        help
  72          Path to a binary PMU firmware configuration object to be linked
  73          into U-Boot SPL and loaded at runtime into the PMU firmware.
  74
  75          The ZynqMP Power Management Unit (PMU) needs a configuration
  76          object for most SoC peripherals to work. To have it loaded by
  77          U-Boot SPL set here the file name (absolute path or relative to
  78          the top source tree) of your configuration, which must be a
  79          binary blob. It will be linked in the SPL binary and loaded
  80          into the PMU firmware by U-Boot SPL during board
  81          initialization.
  82
  83          Leave this option empty if your PMU firmware has a hard-coded
  84          configuration object or you are loading it by any other means.
  85
  86config ZYNQMP_USB
  87        bool "Configure ZynqMP USB"
  88
  89config ZYNQMP_NO_DDR
  90        bool "Disable DDR MMU mapping"
  91        help
  92          This option configures MMU with no DDR to avoid speculative
  93          access to DDR memory where DDR is not present.
  94
  95config SYS_MALLOC_F_LEN
  96        default 0x600
  97
  98config DEFINE_TCM_OCM_MMAP
  99        bool "Define TCM and OCM memory in MMU Table"
 100        default y if MP
 101        help
 102          This option if enabled defines the TCM and OCM memory and its
 103          memory attributes in MMU table entry.
 104
 105config ZYNQMP_PSU_INIT_ENABLED
 106        bool "Include psu_init"
 107        help
 108          Include psu_init to full u-boot. SPL include psu_init by default.
 109
 110config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
 111        bool "Overwrite SPL bootmode"
 112        depends on SPL
 113        help
 114          Overwrite bootmode selected via boot mode pins to tell SPL what should
 115          be the next boot device.
 116
 117config ZYNQ_SDHCI_MAX_FREQ
 118        default 200000000
 119
 120config SPL_ZYNQMP_TWO_SDHCI
 121        bool "Enable booting from both SDHCIs"
 122        depends on SPL
 123        help
 124          This option reflects that board has two SDHCI controllers which
 125          platform can use as boot device. This option ensures that SPL will
 126          setup BOOT_DEVICE_MMC2 for SDHCI1 controller and BOOT_DEVICE_MMC1 for
 127          SDHCI0 controller. Platforms which have only one SDHCI controller
 128          shouldn't enable this option because it for software SDHCI0 or SDHCI1
 129          are both covered by BOOT_DEVICE_MMC1.
 130
 131config SPL_ZYNQMP_ALT_BOOTMODE
 132        hex
 133        default 0x0 if JTAG_MODE
 134        default 0x1 if QSPI_MODE_24BIT
 135        default 0x2 if QSPI_MODE_32BIT
 136        default 0x3 if SD_MODE
 137        default 0x4 if NAND_MODE
 138        default 0x5 if SD_MODE1
 139        default 0x6 if EMMC_MODE
 140        default 0x7 if USB_MODE
 141        default 0xa if SW_USBHOST_MODE
 142        default 0xb if SW_SATA_MODE
 143        default 0xe if SD1_LSHFT_MODE
 144
 145choice
 146        prompt "Boot mode"
 147        depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED
 148        default JTAG_MODE
 149
 150config JTAG_MODE
 151        bool "JTAG_MODE"
 152
 153config QSPI_MODE_24BIT
 154        bool "QSPI_MODE_24BIT"
 155
 156config QSPI_MODE_32BIT
 157        bool "QSPI_MODE_32BIT"
 158
 159config SD_MODE
 160        bool "SD_MODE"
 161
 162config SD_MODE1
 163        bool "SD_MODE1"
 164
 165config NAND_MODE
 166        bool "NAND_MODE"
 167
 168config EMMC_MODE
 169        bool "EMMC_MODE"
 170
 171config USB_MODE
 172        bool "USB"
 173
 174config SW_USBHOST_MODE
 175        bool "SW USBHOST_MODE"
 176
 177config SW_SATA_MODE
 178        bool "SW SATA_MODE"
 179
 180config SD1_LSHFT_MODE
 181        bool "SD1_LSHFT_MODE"
 182
 183endchoice
 184
 185endif
 186