/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2007-2009,2010-2012 Freescale Semiconductor, Inc.
 */

/*
 * mpc8536ds board configuration file
 *
 */
#ifndef __CONFIG_H
#define __CONFIG_H

#include "../board/freescale/common/ics307_clk.h"

#ifdef CONFIG_SDCARD
#define CONFIG_RAMBOOT_SDCARD           1
#define CONFIG_RESET_VECTOR_ADDRESS     0xf8fffffc
#endif

#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH         1
#define CONFIG_RESET_VECTOR_ADDRESS     0xf8fffffc
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif

#ifndef CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
#endif

#define CONFIG_PCI1             1       /* Enable PCI controller 1 */
#define CONFIG_PCIE1            1       /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2            1       /* PCIE controller 2 (slot 2) */
#define CONFIG_PCIE3            1       /* PCIE controller 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
#define CONFIG_PCI_INDIRECT_BRIDGE 1    /* indirect PCI bridge support */
#define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */


#define CONFIG_ENV_OVERWRITE

#define CONFIG_SYS_CLK_FREQ     get_board_sys_clk() /* sysclk for MPC85xx */
#define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()
#define CONFIG_ICS307_REFCLK_HZ 33333000  /* ICS307 clock chip ref freq */

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_L2_CACHE                 /* toggle L2 cache */
#define CONFIG_BTB                      /* toggle branch predition */

#define CONFIG_ENABLE_36BIT_PHYS        1

#ifdef CONFIG_PHYS_64BIT
#define CONFIG_ADDR_MAP                 1
#define CONFIG_SYS_NUM_ADDR_MAP         16      /* number of TLB1 entries */
#endif

#define CONFIG_SYS_MEMTEST_START 0x00010000     /* skip exception vectors */
#define CONFIG_SYS_MEMTEST_END   0x1f000000     /* skip u-boot at top of RAM */

/*
 * Config the L2 Cache as L2 SRAM
 */
#define CONFIG_SYS_INIT_L2_ADDR         0xf8f80000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_INIT_L2_ADDR_PHYS    0xff8f80000ull
#else
#define CONFIG_SYS_INIT_L2_ADDR_PHYS    CONFIG_SYS_INIT_L2_ADDR
#endif
#define CONFIG_SYS_L2_SIZE              (512 << 10)
#define CONFIG_SYS_INIT_L2_END  (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)

#define CONFIG_SYS_CCSRBAR              0xffe00000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR

#if defined(CONFIG_NAND_SPL)
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif

/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SPD_EEPROM               /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD

#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE   0xDeadBeef

#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE

#define CONFIG_DIMM_SLOTS_PER_CTLR      1
#define CONFIG_CHIP_SELECTS_PER_CTRL    2

/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS      0x51    /* CTLR 0 DIMM 0 */
#define CONFIG_SYS_SPD_BUS_NUM          1

/* These are used when DDR doesn't use SPD. */
#define CONFIG_SYS_SDRAM_SIZE           256     /* DDR is 256MB */
#define CONFIG_SYS_DDR_CS0_BNDS 0x0000001F
#define CONFIG_SYS_DDR_CS0_CONFIG       0x80010102 /* Enable, no interleaving */
#define CONFIG_SYS_DDR_TIMING_3 0x00000000
#define CONFIG_SYS_DDR_TIMING_0 0x00260802
#define CONFIG_SYS_DDR_TIMING_1 0x3935d322
#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
#define CONFIG_SYS_DDR_MODE_1           0x00480432
#define CONFIG_SYS_DDR_MODE_2           0x00000000
#define CONFIG_SYS_DDR_INTERVAL 0x06180100
#define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
#define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
#define CONFIG_SYS_DDR_CONTROL  0xC3008000      /* Type = DDR2 */
#define CONFIG_SYS_DDR_CONTROL2 0x04400010

#define CONFIG_SYS_DDR_ERR_INT_EN       0x0000000d
#define CONFIG_SYS_DDR_ERR_DIS          0x00000000
#define CONFIG_SYS_DDR_SBE              0x00010000

/* Make sure required options are set */
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif

#undef CONFIG_CLOCKS_IN_MHZ

/*
 * Memory map -- xxx -this is wrong, needs updating
 *
 * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
 * 0x8000_0000  0xbfff_ffff     PCI Express Mem         1G non-cacheable
 * 0xc000_0000  0xdfff_ffff     PCI                     512M non-cacheable
 * 0xe100_0000  0xe3ff_ffff     PCI IO range            4M non-cacheable
 *
 * Localbus cacheable (TBD)
 * 0xXXXX_XXXX  0xXXXX_XXXX     SRAM                    YZ M Cacheable
 *
 * Localbus non-cacheable
 * 0xe000_0000  0xe7ff_ffff     Promjet/free            128M non-cacheable
 * 0xe800_0000  0xefff_ffff     FLASH                   128M non-cacheable
 * 0xffa0_0000  0xffaf_ffff     NAND                    1M non-cacheable
 * 0xffdf_0000  0xffdf_7fff     PIXIS                   32K non-cacheable TLB0
 * 0xffd0_0000  0xffd0_3fff     L1 for stack            16K Cacheable TLB0
 * 0xffe0_0000  0xffef_ffff     CCSR                    1M non-cacheable
 */

/*
 * Local Bus Definitions
 */
#define CONFIG_SYS_FLASH_BASE           0xe0000000      /* start of FLASH 128M */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
#else
#define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
#endif

#define CONFIG_FLASH_BR_PRELIM \
        (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
#define CONFIG_FLASH_OR_PRELIM  0xf8000ff7

#define CONFIG_SYS_BR1_PRELIM \
                (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
                 | BR_PS_16 | BR_V)
#define CONFIG_SYS_OR1_PRELIM   0xf8000ff7

#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, \
                                      CONFIG_SYS_FLASH_BASE_PHYS }
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
#undef  CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */

#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH)
#define CONFIG_SYS_RAMBOOT
#else
#undef CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7

#define CONFIG_HWCONFIG                 /* enable hwconfig */
#define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
#define PIXIS_BASE      0xffdf0000      /* PIXIS registers */
#ifdef CONFIG_PHYS_64BIT
#define PIXIS_BASE_PHYS 0xfffdf0000ull
#else
#define PIXIS_BASE_PHYS PIXIS_BASE
#endif

#define CONFIG_SYS_BR3_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR3_PRELIM   0xffffeff7      /* 32KB but only 4k mapped */

#define PIXIS_ID                0x0     /* Board ID at offset 0 */
#define PIXIS_VER               0x1     /* Board version at offset 1 */
#define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
#define PIXIS_CSR               0x3     /* PIXIS General control/status register */
#define PIXIS_RST               0x4     /* PIXIS Reset Control register */
#define PIXIS_PWR               0x5     /* PIXIS Power status register */
#define PIXIS_AUX               0x6     /* Auxiliary 1 register */
#define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
#define PIXIS_AUX2              0x8     /* Auxiliary 2 register */
#define PIXIS_VCTL              0x10    /* VELA Control Register */
#define PIXIS_VSTAT             0x11    /* VELA Status Register */
#define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
#define PIXIS_VCORE0            0x14    /* VELA VCORE0 Register */
#define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
#define PIXIS_VBOOT_LBMAP       0xe0    /* VBOOT - CFG_LBMAP */
#define PIXIS_VBOOT_LBMAP_NOR0  0x00    /* cfg_lbmap - boot from NOR 0 */
#define PIXIS_VBOOT_LBMAP_NOR1  0x01    /* cfg_lbmap - boot from NOR 1 */
#define PIXIS_VBOOT_LBMAP_NOR2  0x02    /* cfg_lbmap - boot from NOR 2 */
#define PIXIS_VBOOT_LBMAP_NOR3  0x03    /* cfg_lbmap - boot from NOR 3 */
#define PIXIS_VBOOT_LBMAP_PJET  0x04    /* cfg_lbmap - boot from projet */
#define PIXIS_VBOOT_LBMAP_NAND  0x05    /* cfg_lbmap - boot from NAND */
#define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
#define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
#define PIXIS_VSPEED2           0x19    /* VELA VSpeed 2 */
#define PIXIS_VSYSCLK0          0x1A    /* VELA SYSCLK0 Register */
#define PIXIS_VSYSCLK1          0x1B    /* VELA SYSCLK1 Register */
#define PIXIS_VSYSCLK2          0x1C    /* VELA SYSCLK2 Register */
#define PIXIS_VDDRCLK0          0x1D    /* VELA DDRCLK0 Register */
#define PIXIS_VDDRCLK1          0x1E    /* VELA DDRCLK1 Register */
#define PIXIS_VDDRCLK2          0x1F    /* VELA DDRCLK2 Register */
#define PIXIS_VWATCH            0x24    /* Watchdog Register */
#define PIXIS_LED               0x25    /* LED Register */

#define PIXIS_SPD_SYSCLK        0x7     /* SYSCLK option */

/* old pixis referenced names */
#define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
#define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
#define CONFIG_SYS_PIXIS_VBOOT_MASK     0x4e

#define CONFIG_SYS_INIT_RAM_LOCK        1
#define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000      /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_SIZE        0x00004000      /* Size of used area in RAM */

#define CONFIG_SYS_GBL_DATA_OFFSET \
                (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

#define CONFIG_SYS_MONITOR_LEN  (256 * 1024) /* Reserve 256 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (1024 * 1024)   /* Reserved for malloc */

#ifndef CONFIG_NAND_SPL
#define CONFIG_SYS_NAND_BASE            0xffa00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS       0xfffa00000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
#endif
#else
#define CONFIG_SYS_NAND_BASE            0xfff00000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_NAND_BASE_PHYS       0xffff00000ull
#else
#define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
#endif
#endif
#define CONFIG_SYS_NAND_BASE_LIST     { CONFIG_SYS_NAND_BASE,\
                                CONFIG_SYS_NAND_BASE + 0x40000, \
                                CONFIG_SYS_NAND_BASE + 0x80000, \
                                CONFIG_SYS_NAND_BASE + 0xC0000}
#define CONFIG_SYS_MAX_NAND_DEVICE      4
#define CONFIG_NAND_FSL_ELBC    1
#define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)

/* NAND boot: 4K NAND loader config */
#define CONFIG_SYS_NAND_SPL_SIZE        0x1000
#define CONFIG_SYS_NAND_U_BOOT_SIZE     ((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST      (CONFIG_SYS_INIT_L2_ADDR)
#define CONFIG_SYS_NAND_U_BOOT_START \
                (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_NAND_SPL_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_OFFS     (0)
#define CONFIG_SYS_NAND_U_BOOT_RELOC    (CONFIG_SYS_INIT_L2_END - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP ((CONFIG_SYS_INIT_L2_END - 1) & ~0xF)

/* NAND flash config */
#define CONFIG_SYS_NAND_BR_PRELIM \
                (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                | BR_PS_8               /* Port Size = 8 bit */ \
                | BR_MS_FCM             /* MSEL = FCM */ \
                | BR_V)                 /* valid */
#define CONFIG_SYS_NAND_OR_PRELIM       (0xFFFC0000     /* length 256K */ \
                | OR_FCM_PGS            /* Large Page*/ \
                | OR_FCM_CSCT \
                | OR_FCM_CST \
                | OR_FCM_CHT \
                | OR_FCM_SCY_1 \
                | OR_FCM_TRLX \
                | OR_FCM_EHTR)

#define CONFIG_SYS_BR0_PRELIM  CONFIG_FLASH_BR_PRELIM   /* NOR Base Address */
#define CONFIG_SYS_OR0_PRELIM  CONFIG_FLASH_OR_PRELIM   /* NOR Options */
#define CONFIG_SYS_BR2_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
#define CONFIG_SYS_OR2_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

#define CONFIG_SYS_BR4_PRELIM \
                (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                | BR_PS_8               /* Port Size = 8 bit */ \
                | BR_MS_FCM             /* MSEL = FCM */ \
                | BR_V)                 /* valid */
#define CONFIG_SYS_OR4_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
#define CONFIG_SYS_BR5_PRELIM \
                (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000) \
                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                | BR_PS_8               /* Port Size = 8 bit */ \
                | BR_MS_FCM             /* MSEL = FCM */ \
                | BR_V)                 /* valid */
#define CONFIG_SYS_OR5_PRELIM   CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */

#define CONFIG_SYS_BR6_PRELIM \
                (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000) \
                | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                | BR_PS_8               /* Port Size = 8 bit */ \
                | BR_MS_FCM             /* MSEL = FCM */ \
                | BR_V)                 /* valid */
#define CONFIG_SYS_OR6_PRELIM   CONFIG_SYS_NAND_OR_PRELIM       /* NAND Options */

/* Serial Port - controlled on board with jumper J8
 * open - index 2
 * shorted - index 1
 */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
#ifdef CONFIG_NAND_SPL
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif

#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600)

/*
 * I2C
 */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED       400000
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
#define CONFIG_SYS_I2C_NOPROBES         { {0, 0x29} }

/*
 * I2C2 EEPROM
 */
#define CONFIG_ID_EEPROM
#ifdef CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#endif
#define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
#define CONFIG_SYS_EEPROM_BUS_NUM       1

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */

#define CONFIG_SYS_PCI1_MEM_VIRT        0x80000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCI1_MEM_BUS         0xf0000000
#define CONFIG_SYS_PCI1_MEM_PHYS        0xc00000000ull
#else
#define CONFIG_SYS_PCI1_MEM_BUS         0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS        0x80000000
#endif
#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
#define CONFIG_SYS_PCI1_IO_VIRT         0xffc00000
#define CONFIG_SYS_PCI1_IO_BUS          0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCI1_IO_PHYS         0xfffc00000ull
#else
#define CONFIG_SYS_PCI1_IO_PHYS         0xffc00000
#endif
#define CONFIG_SYS_PCI1_IO_SIZE         0x00010000      /* 64k */

/* controller 1, Slot 1, tgtid 1, Base address a000 */
#define CONFIG_SYS_PCIE1_NAME           "Slot 1"
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x90000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_MEM_BUS        0xf8000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xc10000000ull
#else
#define CONFIG_SYS_PCIE1_MEM_BUS        0x90000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0x90000000
#endif
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x08000000      /* 128M */
#define CONFIG_SYS_PCIE1_IO_VIRT        0xffc10000
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS        0xfffc10000ull
#else
#define CONFIG_SYS_PCIE1_IO_PHYS        0xffc10000
#endif
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */

/* controller 2, Slot 2, tgtid 2, Base address 9000 */
#define CONFIG_SYS_PCIE2_NAME           "Slot 2"
#define CONFIG_SYS_PCIE2_MEM_VIRT       0x98000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_MEM_BUS        0xf8000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0xc18000000ull
#else
#define CONFIG_SYS_PCIE2_MEM_BUS        0x98000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0x98000000
#endif
#define CONFIG_SYS_PCIE2_MEM_SIZE       0x08000000      /* 128M */
#define CONFIG_SYS_PCIE2_IO_VIRT        0xffc20000
#define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS        0xfffc20000ull
#else
#define CONFIG_SYS_PCIE2_IO_PHYS        0xffc20000
#endif
#define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */

/* controller 3, direct to uli, tgtid 3, Base address 8000 */
#define CONFIG_SYS_PCIE3_NAME           "Slot 3"
#define CONFIG_SYS_PCIE3_MEM_VIRT       0xa0000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS       0xc20000000ull
#else
#define CONFIG_SYS_PCIE3_MEM_BUS        0xa0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS       0xa0000000
#endif
#define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE3_IO_VIRT        0xffc30000
#define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE3_IO_PHYS        0xfffc30000ull
#else
#define CONFIG_SYS_PCIE3_IO_PHYS        0xffc30000
#endif
#define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */

#if defined(CONFIG_PCI)
/*PCIE video card used*/
#define VIDEO_IO_OFFSET         CONFIG_SYS_PCIE3_IO_VIRT

/*PCI video card used*/
/*#define VIDEO_IO_OFFSET       CONFIG_SYS_PCI1_IO_VIRT*/

/* video */

#if defined(CONFIG_VIDEO)
#define CONFIG_BIOSEMU
#define CONFIG_ATI_RADEON_FB
#define CONFIG_VIDEO_LOGO
#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE3_IO_VIRT
#endif

#undef CONFIG_EEPRO100
#undef CONFIG_TULIP

#ifndef CONFIG_PCI_PNP
        #define PCI_ENET0_IOADDR        CONFIG_SYS_PCI1_IO_BUS
        #define PCI_ENET0_MEMADDR       CONFIG_SYS_PCI1_IO_BUS
        #define PCI_IDSEL_NUMBER        0x11    /* IDSEL = AD11 */
#endif

#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */

#endif  /* CONFIG_PCI */

/* SATA */
#define CONFIG_SYS_SATA_MAX_DEVICE      2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA

#ifdef CONFIG_FSL_SATA
#define CONFIG_LBA48
#endif

#if defined(CONFIG_TSEC_ENET)

#define CONFIG_MII_DEFAULT_TSEC 1       /* Allow unregistered phys */
#define CONFIG_TSEC1    1
#define CONFIG_TSEC1_NAME       "eTSEC1"
#define CONFIG_TSEC3    1
#define CONFIG_TSEC3_NAME       "eTSEC3"

#define CONFIG_FSL_SGMII_RISER  1
#define SGMII_RISER_PHY_OFFSET  0x1c

#define TSEC1_PHY_ADDR          1       /* TSEC1 -> PHY1 */
#define TSEC3_PHY_ADDR          0       /* TSEC3 -> PHY0 */

#define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)

#define TSEC1_PHYIDX            0
#define TSEC3_PHYIDX            0

#define CONFIG_ETHPRIME         "eTSEC1"

#endif  /* CONFIG_TSEC_ENET */

/*
 * Environment
 */

#if defined(CONFIG_SYS_RAMBOOT)
#if defined(CONFIG_RAMBOOT_SPIFLASH)
#elif defined(CONFIG_RAMBOOT_SDCARD)
#define CONFIG_FSL_FIXED_MMC_LOCATION
#define CONFIG_SYS_MMC_ENV_DEV  0
#endif
#endif

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */

#undef CONFIG_WATCHDOG                  /* watchdog disabled */

#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#endif

/*
 * USB
 */
#define CONFIG_HAS_FSL_MPH_USB
#ifdef CONFIG_HAS_FSL_MPH_USB
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#endif
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#endif

/*
 * Environment Configuration
 */

/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#define CONFIG_HAS_ETH2
#define CONFIG_HAS_ETH3
#endif

#define CONFIG_IPADDR           192.168.1.254

#define CONFIG_HOSTNAME         "unknown"
#define CONFIG_ROOTPATH         "/opt/nfsroot"
#define CONFIG_BOOTFILE         "uImage"
#define CONFIG_UBOOTPATH        u-boot.bin /* U-Boot image on TFTP server */

#define CONFIG_SERVERIP         192.168.1.1
#define CONFIG_GATEWAYIP        192.168.1.1
#define CONFIG_NETMASK          255.255.255.0

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000

#define CONFIG_EXTRA_ENV_SETTINGS                               \
"netdev=eth0\0"                                         \
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
"tftpflash=tftpboot $loadaddr $uboot; "                 \
        "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
                " +$filesize; " \
        "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
                " +$filesize; " \
        "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
                " $filesize; "  \
        "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
                " +$filesize; " \
        "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
                " $filesize\0"  \
"consoledev=ttyS0\0"                            \
"ramdiskaddr=2000000\0"                 \
"ramdiskfile=8536ds/ramdisk.uboot\0"            \
"fdtaddr=1e00000\0"                             \
"fdtfile=8536ds/mpc8536ds.dtb\0"                \
"bdev=sda3\0"                                   \
"hwconfig=usb1:dr_mode=host,phy_type=ulpi\0"

#define CONFIG_HDBOOT                           \
 "setenv bootargs root=/dev/$bdev rw "          \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "tftp $loadaddr $bootfile;"                    \
 "tftp $fdtaddr $fdtfile;"                      \
 "bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND           \
 "setenv bootargs root=/dev/nfs rw "    \
 "nfsroot=$serverip:$rootpath "         \
 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "tftp $loadaddr $bootfile;"            \
 "tftp $fdtaddr $fdtfile;"              \
 "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND           \
 "setenv bootargs root=/dev/ram rw "    \
 "console=$consoledev,$baudrate $othbootargs;"  \
 "tftp $ramdiskaddr $ramdiskfile;"      \
 "tftp $loadaddr $bootfile;"            \
 "tftp $fdtaddr $fdtfile;"              \
 "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND              CONFIG_HDBOOT

#endif  /* __CONFIG_H */