LXR uboot/include/configs/SBx81LIFKW.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
   4 */
   5
   6#ifndef _CONFIG_SBX81LIFKW_H
   7#define _CONFIG_SBX81LIFKW_H
   8
   9/*
  10 * High Level Configuration Options (easy to change)
  11 */
  12#define CONFIG_FEROCEON_88FR131 1       /* CPU Core subversion */
  13#define CONFIG_KW88F6281        1       /* SOC Name */
  14#define CONFIG_SKIP_LOWLEVEL_INIT       /* disable board lowlevel_init */
  15#define CONFIG_SYS_KWD_CONFIG   $(CONFIG_BOARDDIR)/kwbimage.cfg
  16
  17/* additions for new ARM relocation support */
  18#define CONFIG_SYS_SDRAM_BASE   0x00000000
  19
  20#define CONFIG_MD5      /* get_random_hex on krikwood needs MD5 support */
  21#define CONFIG_KIRKWOOD_EGIGA_INIT      /* Enable GbePort0/1 for kernel */
  22#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 */
  23#define CONFIG_KIRKWOOD_RGMII_PAD_1V8   /* Set RGMII Pad voltage to 1.8V */
  24#define CONFIG_KIRKWOOD_GPIO    1
  25
  26/*
  27 * NS16550 Configuration
  28 */
  29#define CONFIG_SYS_NS16550
  30#define CONFIG_SYS_NS16550_SERIAL
  31#define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  32#define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_TCLK
  33#define CONFIG_SYS_NS16550_COM1         KW_UART0_BASE
  34
  35/*
  36 * Serial Port configuration
  37 * The following definitions let you select what serial you want to use
  38 * for your console driver.
  39 */
  40
  41#define CONFIG_CONS_INDEX       1       /*Console on UART0 */
  42
  43/*
  44 * For booting Linux, the board info and command line data
  45 * have to be in the first 8 MB of memory, since this is
  46 * the maximum mapped by the Linux kernel during initialization.
  47 */
  48#define CONFIG_CMDLINE_TAG      1       /* enable passing of ATAGs */
  49#define CONFIG_INITRD_TAG       1       /* enable INITRD tag */
  50#define CONFIG_SETUP_MEMORY_TAGS 1      /* enable memory tag */
  51
  52#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
  53#define MTDPARTS_MTDOOPS "errlog"
  54#define CONFIG_DOS_PARTITION
  55
  56/*
  57 *  Environment variables configurations
  58 */
  59
  60/*
  61 * U-Boot bootcode configuration
  62 */
  63
  64#define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for monitor */
  65#define CONFIG_SYS_MALLOC_LEN             (4 << 20)     /* Reserve 4.0 MB for malloc */
  66
  67/*
  68 * For booting Linux, the board info and command line data
  69 * have to be in the first 8 MB of memory, since this is
  70 * the maximum mapped by the Linux kernel during initialization.
  71 */
  72#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Mem map for Linux*/
  73
  74/* size in bytes reserved for initial data */
  75
  76#include <asm/arch/config.h>
  77/* There is no PHY directly connected so don't ask it for link status */
  78#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  79
  80/*
  81 * Other required minimal configurations
  82 */
  83#define CONFIG_SYS_MEMTEST_START 0x00400000     /* 4M */
  84#define CONFIG_SYS_MEMTEST_END  0x007fffff      /*(_8M -1) */
  85#define CONFIG_SYS_RESET_ADDRESS 0xffff0000     /* Rst Vector Adr */
  86
  87/*
  88 * Ethernet Driver configuration
  89 */
  90#ifdef CONFIG_CMD_NET
  91#define CONFIG_NETCONSOLE       /* include NetConsole support */
  92#define CONFIG_NET_MULTI        /* specify more that one ports available */
  93#define CONFIG_MVGBE    /* Enable kirkwood Gbe Controller Driver */
  94#define CONFIG_MVGBE_PORTS      {1, 0}  /* enable a single port */
  95#define CONFIG_PHY_BASE_ADR     0x01
  96#define CONFIG_ENV_OVERWRITE    /* ethaddr can be reprogrammed */
  97#endif /* CONFIG_CMD_NET */
  98
  99#define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
 100
 101#endif /* _CONFIG_SBX81LIFKW_H */
 102