LXR uboot/include/configs/db-88f6281-bp.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2
   3#ifndef _CONFIG_DB_88F6281_BP_H
   4#define _CONFIG_DB_88F6281_BP_H
   5
   6/*
   7 * High Level Configuration Options (easy to change)
   8 */
   9#define CONFIG_FEROCEON_88FR131 1       /* CPU Core subversion */
  10#define CONFIG_KW88F6281        1       /* SOC Name */
  11#define CONFIG_SKIP_LOWLEVEL_INIT       /* disable board lowlevel_init */
  12#define CONFIG_SYS_TCLK         166666667
  13#define CONFIG_SYS_KWD_CONFIG   $(CONFIG_BOARDDIR)/kwbimage.cfg
  14#define CONFIG_BUILD_TARGET     "u-boot.kwb"
  15
  16/* additions for new ARM relocation support */
  17#define CONFIG_SYS_SDRAM_BASE   0x00000000
  18
  19#define CONFIG_KIRKWOOD_EGIGA_INIT      /* Enable GbePort0/1 for kernel */
  20#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 */
  21#define CONFIG_KIRKWOOD_RGMII_PAD_1V8   /* Set RGMII Pad voltage to 1.8V */
  22#define CONFIG_KIRKWOOD_GPIO    1
  23
  24/*
  25 * NS16550 Configuration
  26 */
  27#define CONFIG_SYS_NS16550_SERIAL
  28#define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  29#define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_TCLK
  30#define CONFIG_SYS_NS16550_COM1         KW_UART0_BASE
  31
  32#define CONFIG_SYS_MAX_NAND_DEVICE     1
  33/*
  34 * Serial Port configuration
  35 * The following definitions let you select what serial you want to use
  36 * for your console driver.
  37 */
  38
  39#define CONFIG_CONS_INDEX       1       /* Console on UART0 */
  40
  41/*
  42 *  Environment variables configurations
  43 */
  44#define CONFIG_ENV_SPI_BUS              0
  45#define CONFIG_ENV_SPI_CS               0
  46#define CONFIG_ENV_SPI_MAX_HZ           20000000        /* 20Mhz */
  47#define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
  48
  49/*
  50 * U-Boot bootcode configuration
  51 */
  52
  53#define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for monitor */
  54#define CONFIG_SYS_MALLOC_LEN             (4 << 20)     /* Reserve 4.0 MB for malloc */
  55
  56/*
  57 * For booting Linux, the board info and command line data
  58 * have to be in the first 8 MB of memory, since this is
  59 * the maximum mapped by the Linux kernel during initialization.
  60 */
  61#define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Mem map for Linux*/
  62
  63/* size in bytes reserved for initial data */
  64
  65#include <asm/arch/config.h>
  66/* There is no PHY directly connected so don't ask it for link status */
  67#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  68
  69/*
  70 * Other required minimal configurations
  71 */
  72#define CONFIG_SYS_MEMTEST_START 0x00400000     /* 4M */
  73#define CONFIG_SYS_MEMTEST_END  0x007fffff      /* (_8M - 1) */
  74#define CONFIG_SYS_RESET_ADDRESS 0xffff0000     /* Rst Vector Adr */
  75
  76/*
  77 * SDIO/MMC Card Configuration
  78 */
  79#ifdef CONFIG_CMD_MMC
  80#define CONFIG_MVEBU_MMC
  81#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE
  82#endif /* CONFIG_CMD_MMC */
  83
  84/*
  85 * SATA Driver configuration
  86 */
  87#ifdef CONFIG_MVSATA_IDE
  88#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
  89#endif /*CONFIG_MVSATA_IDE*/
  90
  91#define CONFIG_SYS_LOAD_ADDR  0x1000000      /* default location for tftp and bootm */
  92
  93#endif /* _CONFIG_DB_88F6281_BP_H */
  94