1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz> 4 */ 5 6#ifndef _CONFIG_SBX81LIFXCAT_H 7#define _CONFIG_SBX81LIFXCAT_H 8 9/* 10 * High Level Configuration Options (easy to change) 11 */ 12#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ 13#define CONFIG_KW88F6281 1 /* SOC Name */ 14#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 15#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg 16 17/* additions for new ARM relocation support */ 18#define CONFIG_SYS_SDRAM_BASE 0x00000000 19 20#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ 21#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ 22#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ 23#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ 24#define CONFIG_KIRKWOOD_GPIO 1 25 26/* 27 * NS16550 Configuration 28 */ 29#define CONFIG_SYS_NS16550 30#define CONFIG_SYS_NS16550_SERIAL 31#define CONFIG_SYS_NS16550_REG_SIZE (-4) 32#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK 33#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE 34 35/* 36 * Serial Port configuration 37 * The following definitions let you select what serial you want to use 38 * for your console driver. 39 */ 40 41#define CONFIG_CONS_INDEX 1 /*Console on UART0 */ 42 43/* 44 * For booting Linux, the board info and command line data 45 * have to be in the first 8 MB of memory, since this is 46 * the maximum mapped by the Linux kernel during initialization. 47 */ 48#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ 49#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ 50#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ 51 52#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)" 53#define MTDPARTS_MTDOOPS "errlog" 54#define CONFIG_DOS_PARTITION 55 56/* 57 * Environment variables configurations 58 */ 59 60/* 61 * U-Boot bootcode configuration 62 */ 63 64#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ 65#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ 66 67/* 68 * For booting Linux, the board info and command line data 69 * have to be in the first 8 MB of memory, since this is 70 * the maximum mapped by the Linux kernel during initialization. 71 */ 72#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ 73 74/* size in bytes reserved for initial data */ 75 76#include <asm/arch/config.h> 77/* There is no PHY directly connected so don't ask it for link status */ 78#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 79 80/* 81 * Other required minimal configurations 82 */ 83#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ 84#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ 85#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ 86 87/* 88 * Ethernet Driver configuration 89 */ 90#ifdef CONFIG_CMD_NET 91#define CONFIG_NETCONSOLE /* include NetConsole support */ 92#define CONFIG_NET_MULTI /* specify more that one ports available */ 93#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */ 94#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */ 95#define CONFIG_PHY_BASE_ADR 0x01 96#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ 97#endif /* CONFIG_CMD_NET */ 98 99#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ 100 101#endif /* _CONFIG_SBX81LIFXCAT_H */ 102