1/* SPDX-License-Identifier: GPL-2.0+ */ 2 3#ifndef _CONFIG_DB_88F6281_BP_H 4#define _CONFIG_DB_88F6281_BP_H 5 6/* 7 * High Level Configuration Options (easy to change) 8 */ 9#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ 10#define CONFIG_KW88F6281 1 /* SOC Name */ 11#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 12#define CONFIG_SYS_TCLK 166666667 13#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg 14#define CONFIG_BUILD_TARGET "u-boot.kwb" 15 16/* additions for new ARM relocation support */ 17#define CONFIG_SYS_SDRAM_BASE 0x00000000 18 19#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ 20#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ 21#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ 22#define CONFIG_KIRKWOOD_GPIO 1 23 24/* 25 * NS16550 Configuration 26 */ 27#define CONFIG_SYS_NS16550_SERIAL 28#define CONFIG_SYS_NS16550_REG_SIZE (-4) 29#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK 30#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE 31 32#define CONFIG_SYS_MAX_NAND_DEVICE 1 33/* 34 * Serial Port configuration 35 * The following definitions let you select what serial you want to use 36 * for your console driver. 37 */ 38 39#define CONFIG_CONS_INDEX 1 /* Console on UART0 */ 40 41/* 42 * Environment variables configurations 43 */ 44#define CONFIG_ENV_SPI_BUS 0 45#define CONFIG_ENV_SPI_CS 0 46#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */ 47#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE 48 49/* 50 * U-Boot bootcode configuration 51 */ 52 53#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ 54#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ 55 56/* 57 * For booting Linux, the board info and command line data 58 * have to be in the first 8 MB of memory, since this is 59 * the maximum mapped by the Linux kernel during initialization. 60 */ 61#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ 62 63/* size in bytes reserved for initial data */ 64 65#include <asm/arch/config.h> 66/* There is no PHY directly connected so don't ask it for link status */ 67#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 68 69/* 70 * Other required minimal configurations 71 */ 72#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */ 73#define CONFIG_SYS_MEMTEST_END 0x007fffff /* (_8M - 1) */ 74#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ 75 76/* 77 * SDIO/MMC Card Configuration 78 */ 79#ifdef CONFIG_CMD_MMC 80#define CONFIG_MVEBU_MMC 81#define CONFIG_SYS_MMC_BASE KW_SDIO_BASE 82#endif /* CONFIG_CMD_MMC */ 83 84/* 85 * SATA Driver configuration 86 */ 87#ifdef CONFIG_MVSATA_IDE 88#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET 89#endif /*CONFIG_MVSATA_IDE*/ 90 91#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ 92 93#endif /* _CONFIG_DB_88F6281_BP_H */ 94