LXR uboot/board/freescale/ls1046ardb/ddr.c

   1// SPDX-License-Identifier: GPL-2.0+
   2/*
   3 * Copyright 2016 Freescale Semiconductor, Inc.
   4 */
   5
   6#include <common.h>
   7#include <fsl_ddr_sdram.h>
   8#include <fsl_ddr_dimm_params.h>
   9#include "ddr.h"
  10#ifdef CONFIG_FSL_DEEP_SLEEP
  11#include <fsl_sleep.h>
  12#endif
  13#include <log.h>
  14#include <asm/arch/clock.h>
  15
  16DECLARE_GLOBAL_DATA_PTR;
  17
  18void fsl_ddr_board_options(memctl_options_t *popts,
  19                           dimm_params_t *pdimm,
  20                           unsigned int ctrl_num)
  21{
  22        const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  23        ulong ddr_freq;
  24
  25        if (ctrl_num > 1) {
  26                printf("Not supported controller number %d\n", ctrl_num);
  27                return;
  28        }
  29        if (!pdimm->n_ranks)
  30                return;
  31
  32        if (popts->registered_dimm_en)
  33                pbsp = rdimms[0];
  34        else
  35                pbsp = udimms[0];
  36
  37        /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  38         * freqency and n_banks specified in board_specific_parameters table.
  39         */
  40        ddr_freq = get_ddr_freq(0) / 1000000;
  41        while (pbsp->datarate_mhz_high) {
  42                if (pbsp->n_ranks == pdimm->n_ranks) {
  43                        if (ddr_freq <= pbsp->datarate_mhz_high) {
  44                                popts->clk_adjust = pbsp->clk_adjust;
  45                                popts->wrlvl_start = pbsp->wrlvl_start;
  46                                popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  47                                popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  48                                goto found;
  49                        }
  50                        pbsp_highest = pbsp;
  51                }
  52                pbsp++;
  53        }
  54
  55        if (pbsp_highest) {
  56                printf("Error: board specific timing not found for %lu MT/s\n",
  57                       ddr_freq);
  58                printf("Trying to use the highest speed (%u) parameters\n",
  59                       pbsp_highest->datarate_mhz_high);
  60                popts->clk_adjust = pbsp_highest->clk_adjust;
  61                popts->wrlvl_start = pbsp_highest->wrlvl_start;
  62                popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  63                popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  64        } else {
  65                panic("DIMM is not supported by this board");
  66        }
  67found:
  68        debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
  69              pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
  70
  71        popts->data_bus_width = 0;      /* 64-bit data bus */
  72        popts->bstopre = 0;             /* enable auto precharge */
  73
  74        /*
  75         * Factors to consider for half-strength driver enable:
  76         *      - number of DIMMs installed
  77         */
  78        popts->half_strength_driver_enable = 0;
  79        /*
  80         * Write leveling override
  81         */
  82        popts->wrlvl_override = 1;
  83        popts->wrlvl_sample = 0xf;
  84
  85        /*
  86         * Rtt and Rtt_WR override
  87         */
  88        popts->rtt_override = 0;
  89
  90        /* Enable ZQ calibration */
  91        popts->zq_en = 1;
  92
  93        popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
  94        popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
  95                          DDR_CDR2_VREF_TRAIN_EN | DDR_CDR2_VREF_RANGE_2;
  96
  97        /* optimize cpo for erratum A-009942 */
  98        popts->cpo_sample = 0x61;
  99}
 100
 101#ifdef CONFIG_TFABOOT
 102int fsl_initdram(void)
 103{
 104        gd->ram_size = tfa_get_dram_size();
 105
 106        if (!gd->ram_size)
 107                gd->ram_size = fsl_ddr_sdram_size();
 108
 109        return 0;
 110}
 111#else
 112int fsl_initdram(void)
 113{
 114        phys_size_t dram_size;
 115
 116#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
 117        gd->ram_size = fsl_ddr_sdram_size();
 118
 119        return 0;
 120#else
 121        puts("Initializing DDR....using SPD\n");
 122
 123        dram_size = fsl_ddr_sdram();
 124#endif
 125
 126        erratum_a008850_post();
 127
 128        gd->ram_size = dram_size;
 129
 130        return 0;
 131}
 132#endif
 133