LXR uboot/include/configs/ls1012a2g5rdb.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * Copyright 2017 NXP
   4 */
   5
   6#ifndef __LS1012A2G5RDB_H__
   7#define __LS1012A2G5RDB_H__
   8
   9#include "ls1012a_common.h"
  10
  11/* DDR */
  12#define CONFIG_DIMM_SLOTS_PER_CTLR      1
  13#define CONFIG_CHIP_SELECTS_PER_CTRL    1
  14#define CONFIG_SYS_SDRAM_SIZE           0x40000000
  15
  16/*  MMC  */
  17#ifdef CONFIG_MMC
  18#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
  19#endif
  20
  21/* SATA */
  22#define CONFIG_LIBATA
  23#define CONFIG_SCSI_AHCI
  24#define CONFIG_SCSI_AHCI_PLAT
  25
  26#define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
  27
  28#define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  29#define CONFIG_SYS_SCSI_MAX_LUN                 1
  30#define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  31                                                CONFIG_SYS_SCSI_MAX_LUN)
  32
  33#undef CONFIG_EXTRA_ENV_SETTINGS
  34#define CONFIG_EXTRA_ENV_SETTINGS               \
  35        "verify=no\0"                           \
  36        "fdt_high=0xffffffffffffffff\0"         \
  37        "initrd_high=0xffffffffffffffff\0"      \
  38        "fdt_addr=0x00f00000\0"                 \
  39        "kernel_addr=0x01000000\0"              \
  40        "kernelheader_addr=0x800000\0"          \
  41        "scriptaddr=0x80000000\0"               \
  42        "scripthdraddr=0x80080000\0"            \
  43        "fdtheader_addr_r=0x80100000\0"         \
  44        "kernelheader_addr_r=0x80200000\0"      \
  45        "kernel_addr_r=0x81000000\0"            \
  46        "fdt_addr_r=0x90000000\0"               \
  47        "load_addr=0xa0000000\0"                \
  48        "kernel_size=0x2800000\0"               \
  49        "kernelheader_size=0x40000\0"           \
  50        "console=ttyS0,115200\0"                \
  51        BOOTENV                                 \
  52        "boot_scripts=ls1012ardb_boot.scr\0"    \
  53        "boot_script_hdr=hdr_ls1012ardb_bs.out\0"       \
  54        "scan_dev_for_boot_part="               \
  55             "part list ${devtype} ${devnum} devplist; "        \
  56             "env exists devplist || setenv devplist 1; "       \
  57             "for distro_bootpart in ${devplist}; do "          \
  58                  "if fstype ${devtype} "                       \
  59                      "${devnum}:${distro_bootpart} "           \
  60                      "bootfstype; then "                       \
  61                      "run scan_dev_for_boot; " \
  62                  "fi; "                        \
  63              "done\0"                          \
  64        "scan_dev_for_boot="                              \
  65                "echo Scanning ${devtype} "               \
  66                                "${devnum}:${distro_bootpart}...; "  \
  67                "for prefix in ${boot_prefixes}; do "     \
  68                        "run scan_dev_for_scripts; "      \
  69                "done;"                                   \
  70                "\0"                                      \
  71        "boot_a_script="                                  \
  72                "load ${devtype} ${devnum}:${distro_bootpart} "  \
  73                        "${scriptaddr} ${prefix}${script}; "    \
  74                "env exists secureboot && load ${devtype} "     \
  75                        "${devnum}:${distro_bootpart} "         \
  76                        "${scripthdraddr} ${prefix}${boot_script_hdr} " \
  77                        "&& esbc_validate ${scripthdraddr};"    \
  78                "source ${scriptaddr}\0"          \
  79        "installer=load mmc 0:2 $load_addr "    \
  80                   "/flex_installer_arm64.itb; "        \
  81                   "bootm $load_addr#$board\0"  \
  82        "qspi_bootcmd=pfe stop; echo Trying load from qspi..;"  \
  83                "sf probe && sf read $load_addr "       \
  84                "$kernel_addr $kernel_size; env exists secureboot "     \
  85                "&& sf read $kernelheader_addr_r $kernelheader_addr "   \
  86                "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
  87                "bootm $load_addr#$board\0"
  88
  89#undef CONFIG_BOOTCOMMAND
  90#ifdef CONFIG_TFABOOT
  91#undef QSPI_NOR_BOOTCOMMAND
  92#define QSPI_NOR_BOOTCOMMAND "pfe stop;run distro_bootcmd; run qspi_bootcmd; " \
  93                             "env exists secureboot && esbc_halt;"
  94#else
  95#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI)
  96#define CONFIG_BOOTCOMMAND "pfe stop;run distro_bootcmd; run qspi_bootcmd; " \
  97                           "env exists secureboot && esbc_halt;"
  98#endif
  99#endif
 100
 101#define DEFAULT_PFE_MDIO_NAME "PFE_MDIO"
 102#define DEFAULT_PFE_MDIO1_NAME "PFE_MDIO1"
 103
 104#include <asm/fsl_secure_boot.h>
 105
 106#endif /* __LS1012A2G5RDB_H__ */
 107