uboot/drivers/net/zynq_gem.c
<<
>>
Prefs
   1// SPDX-License-Identifier: GPL-2.0+
   2/*
   3 * (C) Copyright 2011 Michal Simek
   4 *
   5 * Michal SIMEK <monstr@monstr.eu>
   6 *
   7 * Based on Xilinx gmac driver:
   8 * (C) Copyright 2011 Xilinx
   9 */
  10
  11#include <clk.h>
  12#include <common.h>
  13#include <cpu_func.h>
  14#include <dm.h>
  15#include <log.h>
  16#include <net.h>
  17#include <netdev.h>
  18#include <config.h>
  19#include <console.h>
  20#include <malloc.h>
  21#include <asm/cache.h>
  22#include <asm/io.h>
  23#include <phy.h>
  24#include <miiphy.h>
  25#include <wait_bit.h>
  26#include <watchdog.h>
  27#include <asm/system.h>
  28#include <asm/arch/hardware.h>
  29#include <asm/arch/sys_proto.h>
  30#include <dm/device_compat.h>
  31#include <linux/bitops.h>
  32#include <linux/err.h>
  33#include <linux/errno.h>
  34
  35/* Bit/mask specification */
  36#define ZYNQ_GEM_PHYMNTNC_OP_MASK       0x40020000 /* operation mask bits */
  37#define ZYNQ_GEM_PHYMNTNC_OP_R_MASK     0x20000000 /* read operation */
  38#define ZYNQ_GEM_PHYMNTNC_OP_W_MASK     0x10000000 /* write operation */
  39#define ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK      23 /* Shift bits for PHYAD */
  40#define ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK      18 /* Shift bits for PHREG */
  41
  42#define ZYNQ_GEM_RXBUF_EOF_MASK         0x00008000 /* End of frame. */
  43#define ZYNQ_GEM_RXBUF_SOF_MASK         0x00004000 /* Start of frame. */
  44#define ZYNQ_GEM_RXBUF_LEN_MASK         0x00003FFF /* Mask for length field */
  45
  46#define ZYNQ_GEM_RXBUF_WRAP_MASK        0x00000002 /* Wrap bit, last BD */
  47#define ZYNQ_GEM_RXBUF_NEW_MASK         0x00000001 /* Used bit.. */
  48#define ZYNQ_GEM_RXBUF_ADD_MASK         0xFFFFFFFC /* Mask for address */
  49
  50/* Wrap bit, last descriptor */
  51#define ZYNQ_GEM_TXBUF_WRAP_MASK        0x40000000
  52#define ZYNQ_GEM_TXBUF_LAST_MASK        0x00008000 /* Last buffer */
  53#define ZYNQ_GEM_TXBUF_USED_MASK        0x80000000 /* Used by Hw */
  54
  55#define ZYNQ_GEM_NWCTRL_TXEN_MASK       0x00000008 /* Enable transmit */
  56#define ZYNQ_GEM_NWCTRL_RXEN_MASK       0x00000004 /* Enable receive */
  57#define ZYNQ_GEM_NWCTRL_MDEN_MASK       0x00000010 /* Enable MDIO port */
  58#define ZYNQ_GEM_NWCTRL_STARTTX_MASK    0x00000200 /* Start tx (tx_go) */
  59
  60#define ZYNQ_GEM_NWCFG_SPEED100         0x00000001 /* 100 Mbps operation */
  61#define ZYNQ_GEM_NWCFG_SPEED1000        0x00000400 /* 1Gbps operation */
  62#define ZYNQ_GEM_NWCFG_FDEN             0x00000002 /* Full Duplex mode */
  63#define ZYNQ_GEM_NWCFG_FSREM            0x00020000 /* FCS removal */
  64#define ZYNQ_GEM_NWCFG_SGMII_ENBL       0x08000000 /* SGMII Enable */
  65#define ZYNQ_GEM_NWCFG_PCS_SEL          0x00000800 /* PCS select */
  66#ifdef CONFIG_ARM64
  67#define ZYNQ_GEM_NWCFG_MDCCLKDIV        0x00100000 /* Div pclk by 64, max 160MHz */
  68#else
  69#define ZYNQ_GEM_NWCFG_MDCCLKDIV        0x000c0000 /* Div pclk by 48, max 120MHz */
  70#endif
  71
  72#ifdef CONFIG_ARM64
  73# define ZYNQ_GEM_DBUS_WIDTH    (1 << 21) /* 64 bit bus */
  74#else
  75# define ZYNQ_GEM_DBUS_WIDTH    (0 << 21) /* 32 bit bus */
  76#endif
  77
  78#define ZYNQ_GEM_NWCFG_INIT             (ZYNQ_GEM_DBUS_WIDTH | \
  79                                        ZYNQ_GEM_NWCFG_FDEN | \
  80                                        ZYNQ_GEM_NWCFG_FSREM | \
  81                                        ZYNQ_GEM_NWCFG_MDCCLKDIV)
  82
  83#define ZYNQ_GEM_NWSR_MDIOIDLE_MASK     0x00000004 /* PHY management idle */
  84
  85#define ZYNQ_GEM_DMACR_BLENGTH          0x00000004 /* INCR4 AHB bursts */
  86/* Use full configured addressable space (8 Kb) */
  87#define ZYNQ_GEM_DMACR_RXSIZE           0x00000300
  88/* Use full configured addressable space (4 Kb) */
  89#define ZYNQ_GEM_DMACR_TXSIZE           0x00000400
  90/* Set with binary 00011000 to use 1536 byte(1*max length frame/buffer) */
  91#define ZYNQ_GEM_DMACR_RXBUF            0x00180000
  92
  93#if defined(CONFIG_PHYS_64BIT)
  94# define ZYNQ_GEM_DMA_BUS_WIDTH         BIT(30) /* 64 bit bus */
  95#else
  96# define ZYNQ_GEM_DMA_BUS_WIDTH         (0 << 30) /* 32 bit bus */
  97#endif
  98
  99#define ZYNQ_GEM_DMACR_INIT             (ZYNQ_GEM_DMACR_BLENGTH | \
 100                                        ZYNQ_GEM_DMACR_RXSIZE | \
 101                                        ZYNQ_GEM_DMACR_TXSIZE | \
 102                                        ZYNQ_GEM_DMACR_RXBUF | \
 103                                        ZYNQ_GEM_DMA_BUS_WIDTH)
 104
 105#define ZYNQ_GEM_TSR_DONE               0x00000020 /* Tx done mask */
 106
 107#define ZYNQ_GEM_PCS_CTL_ANEG_ENBL      0x1000
 108
 109#define ZYNQ_GEM_DCFG_DBG6_DMA_64B      BIT(23)
 110
 111/* Use MII register 1 (MII status register) to detect PHY */
 112#define PHY_DETECT_REG  1
 113
 114/* Mask used to verify certain PHY features (or register contents)
 115 * in the register above:
 116 *  0x1000: 10Mbps full duplex support
 117 *  0x0800: 10Mbps half duplex support
 118 *  0x0008: Auto-negotiation support
 119 */
 120#define PHY_DETECT_MASK 0x1808
 121
 122/* TX BD status masks */
 123#define ZYNQ_GEM_TXBUF_FRMLEN_MASK      0x000007ff
 124#define ZYNQ_GEM_TXBUF_EXHAUSTED        0x08000000
 125#define ZYNQ_GEM_TXBUF_UNDERRUN         0x10000000
 126
 127/* Clock frequencies for different speeds */
 128#define ZYNQ_GEM_FREQUENCY_10   2500000UL
 129#define ZYNQ_GEM_FREQUENCY_100  25000000UL
 130#define ZYNQ_GEM_FREQUENCY_1000 125000000UL
 131
 132#define RXCLK_EN                BIT(0)
 133
 134/* Device registers */
 135struct zynq_gem_regs {
 136        u32 nwctrl; /* 0x0 - Network Control reg */
 137        u32 nwcfg; /* 0x4 - Network Config reg */
 138        u32 nwsr; /* 0x8 - Network Status reg */
 139        u32 reserved1;
 140        u32 dmacr; /* 0x10 - DMA Control reg */
 141        u32 txsr; /* 0x14 - TX Status reg */
 142        u32 rxqbase; /* 0x18 - RX Q Base address reg */
 143        u32 txqbase; /* 0x1c - TX Q Base address reg */
 144        u32 rxsr; /* 0x20 - RX Status reg */
 145        u32 reserved2[2];
 146        u32 idr; /* 0x2c - Interrupt Disable reg */
 147        u32 reserved3;
 148        u32 phymntnc; /* 0x34 - Phy Maintaince reg */
 149        u32 reserved4[18];
 150        u32 hashl; /* 0x80 - Hash Low address reg */
 151        u32 hashh; /* 0x84 - Hash High address reg */
 152#define LADDR_LOW       0
 153#define LADDR_HIGH      1
 154        u32 laddr[4][LADDR_HIGH + 1]; /* 0x8c - Specific1 addr low/high reg */
 155        u32 match[4]; /* 0xa8 - Type ID1 Match reg */
 156        u32 reserved6[18];
 157#define STAT_SIZE       44
 158        u32 stat[STAT_SIZE]; /* 0x100 - Octects transmitted Low reg */
 159        u32 reserved9[20];
 160        u32 pcscntrl;
 161        u32 rserved12[36];
 162        u32 dcfg6; /* 0x294 Design config reg6 */
 163        u32 reserved7[106];
 164        u32 transmit_q1_ptr; /* 0x440 - Transmit priority queue 1 */
 165        u32 reserved8[15];
 166        u32 receive_q1_ptr; /* 0x480 - Receive priority queue 1 */
 167        u32 reserved10[17];
 168        u32 upper_txqbase; /* 0x4C8 - Upper tx_q base addr */
 169        u32 reserved11[2];
 170        u32 upper_rxqbase; /* 0x4D4 - Upper rx_q base addr */
 171};
 172
 173/* BD descriptors */
 174struct emac_bd {
 175        u32 addr; /* Next descriptor pointer */
 176        u32 status;
 177#if defined(CONFIG_PHYS_64BIT)
 178        u32 addr_hi;
 179        u32 reserved;
 180#endif
 181};
 182
 183/* Reduce amount of BUFs if you have limited amount of memory */
 184#define RX_BUF 32
 185/* Page table entries are set to 1MB, or multiples of 1MB
 186 * (not < 1MB). driver uses less bd's so use 1MB bdspace.
 187 */
 188#define BD_SPACE        0x100000
 189/* BD separation space */
 190#define BD_SEPRN_SPACE  (RX_BUF * sizeof(struct emac_bd))
 191
 192/* Setup the first free TX descriptor */
 193#define TX_FREE_DESC    2
 194
 195/* Initialized, rxbd_current, rx_first_buf must be 0 after init */
 196struct zynq_gem_priv {
 197        struct emac_bd *tx_bd;
 198        struct emac_bd *rx_bd;
 199        char *rxbuffers;
 200        u32 rxbd_current;
 201        u32 rx_first_buf;
 202        int phyaddr;
 203        int init;
 204        struct zynq_gem_regs *iobase;
 205        struct zynq_gem_regs *mdiobase;
 206        phy_interface_t interface;
 207        struct phy_device *phydev;
 208        ofnode phy_of_node;
 209        struct mii_dev *bus;
 210        struct clk rx_clk;
 211        struct clk tx_clk;
 212        u32 max_speed;
 213        bool int_pcs;
 214        bool dma_64bit;
 215        u32 clk_en_info;
 216};
 217
 218static int phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
 219                        u32 op, u16 *data)
 220{
 221        u32 mgtcr;
 222        struct zynq_gem_regs *regs = priv->mdiobase;
 223        int err;
 224
 225        err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
 226                                true, 20000, false);
 227        if (err)
 228                return err;
 229
 230        /* Construct mgtcr mask for the operation */
 231        mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
 232                (phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
 233                (regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;
 234
 235        /* Write mgtcr and wait for completion */
 236        writel(mgtcr, &regs->phymntnc);
 237
 238        err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
 239                                true, 20000, false);
 240        if (err)
 241                return err;
 242
 243        if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
 244                *data = readl(&regs->phymntnc);
 245
 246        return 0;
 247}
 248
 249static int phyread(struct zynq_gem_priv *priv, u32 phy_addr,
 250                   u32 regnum, u16 *val)
 251{
 252        int ret;
 253
 254        ret = phy_setup_op(priv, phy_addr, regnum,
 255                           ZYNQ_GEM_PHYMNTNC_OP_R_MASK, val);
 256
 257        if (!ret)
 258                debug("%s: phy_addr %d, regnum 0x%x, val 0x%x\n", __func__,
 259                      phy_addr, regnum, *val);
 260
 261        return ret;
 262}
 263
 264static int phywrite(struct zynq_gem_priv *priv, u32 phy_addr,
 265                    u32 regnum, u16 data)
 266{
 267        debug("%s: phy_addr %d, regnum 0x%x, data 0x%x\n", __func__, phy_addr,
 268              regnum, data);
 269
 270        return phy_setup_op(priv, phy_addr, regnum,
 271                            ZYNQ_GEM_PHYMNTNC_OP_W_MASK, &data);
 272}
 273
 274static int zynq_gem_setup_mac(struct udevice *dev)
 275{
 276        u32 i, macaddrlow, macaddrhigh;
 277        struct eth_pdata *pdata = dev_get_plat(dev);
 278        struct zynq_gem_priv *priv = dev_get_priv(dev);
 279        struct zynq_gem_regs *regs = priv->iobase;
 280
 281        /* Set the MAC bits [31:0] in BOT */
 282        macaddrlow = pdata->enetaddr[0];
 283        macaddrlow |= pdata->enetaddr[1] << 8;
 284        macaddrlow |= pdata->enetaddr[2] << 16;
 285        macaddrlow |= pdata->enetaddr[3] << 24;
 286
 287        /* Set MAC bits [47:32] in TOP */
 288        macaddrhigh = pdata->enetaddr[4];
 289        macaddrhigh |= pdata->enetaddr[5] << 8;
 290
 291        for (i = 0; i < 4; i++) {
 292                writel(0, &regs->laddr[i][LADDR_LOW]);
 293                writel(0, &regs->laddr[i][LADDR_HIGH]);
 294                /* Do not use MATCHx register */
 295                writel(0, &regs->match[i]);
 296        }
 297
 298        writel(macaddrlow, &regs->laddr[0][LADDR_LOW]);
 299        writel(macaddrhigh, &regs->laddr[0][LADDR_HIGH]);
 300
 301        return 0;
 302}
 303
 304static int zynq_phy_init(struct udevice *dev)
 305{
 306        int ret;
 307        struct zynq_gem_priv *priv = dev_get_priv(dev);
 308        struct zynq_gem_regs *regs_mdio = priv->mdiobase;
 309        const u32 supported = SUPPORTED_10baseT_Half |
 310                        SUPPORTED_10baseT_Full |
 311                        SUPPORTED_100baseT_Half |
 312                        SUPPORTED_100baseT_Full |
 313                        SUPPORTED_1000baseT_Half |
 314                        SUPPORTED_1000baseT_Full;
 315
 316        /* Enable only MDIO bus */
 317        writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs_mdio->nwctrl);
 318
 319        priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
 320                                   priv->interface);
 321        if (!priv->phydev)
 322                return -ENODEV;
 323
 324        if (priv->max_speed) {
 325                ret = phy_set_supported(priv->phydev, priv->max_speed);
 326                if (ret)
 327                        return ret;
 328        }
 329
 330        priv->phydev->supported &= supported | ADVERTISED_Pause |
 331                                  ADVERTISED_Asym_Pause;
 332
 333        priv->phydev->advertising = priv->phydev->supported;
 334        priv->phydev->node = priv->phy_of_node;
 335
 336        return phy_config(priv->phydev);
 337}
 338
 339static int zynq_gem_init(struct udevice *dev)
 340{
 341        u32 i, nwconfig;
 342        int ret;
 343        unsigned long clk_rate = 0;
 344        struct zynq_gem_priv *priv = dev_get_priv(dev);
 345        struct zynq_gem_regs *regs = priv->iobase;
 346        struct zynq_gem_regs *regs_mdio = priv->mdiobase;
 347        struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC];
 348        struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2];
 349
 350        if (readl(&regs->dcfg6) & ZYNQ_GEM_DCFG_DBG6_DMA_64B)
 351                priv->dma_64bit = true;
 352        else
 353                priv->dma_64bit = false;
 354
 355#if defined(CONFIG_PHYS_64BIT)
 356        if (!priv->dma_64bit) {
 357                printf("ERR: %s: Using 64-bit DMA but HW doesn't support it\n",
 358                       __func__);
 359                return -EINVAL;
 360        }
 361#else
 362        if (priv->dma_64bit)
 363                debug("WARN: %s: Not using 64-bit dma even HW supports it\n",
 364                      __func__);
 365#endif
 366
 367        if (!priv->init) {
 368                /* Disable all interrupts */
 369                writel(0xFFFFFFFF, &regs->idr);
 370
 371                /* Disable the receiver & transmitter */
 372                writel(0, &regs->nwctrl);
 373                writel(0, &regs->txsr);
 374                writel(0, &regs->rxsr);
 375                writel(0, &regs->phymntnc);
 376
 377                /* Clear the Hash registers for the mac address
 378                 * pointed by AddressPtr
 379                 */
 380                writel(0x0, &regs->hashl);
 381                /* Write bits [63:32] in TOP */
 382                writel(0x0, &regs->hashh);
 383
 384                /* Clear all counters */
 385                for (i = 0; i < STAT_SIZE; i++)
 386                        readl(&regs->stat[i]);
 387
 388                /* Setup RxBD space */
 389                memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));
 390
 391                for (i = 0; i < RX_BUF; i++) {
 392                        priv->rx_bd[i].status = 0xF0000000;
 393                        priv->rx_bd[i].addr =
 394                                        (lower_32_bits((ulong)(priv->rxbuffers)
 395                                                        + (i * PKTSIZE_ALIGN)));
 396#if defined(CONFIG_PHYS_64BIT)
 397                        priv->rx_bd[i].addr_hi =
 398                                        (upper_32_bits((ulong)(priv->rxbuffers)
 399                                                        + (i * PKTSIZE_ALIGN)));
 400#endif
 401        }
 402                /* WRAP bit to last BD */
 403                priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
 404                /* Write RxBDs to IP */
 405                writel(lower_32_bits((ulong)priv->rx_bd), &regs->rxqbase);
 406#if defined(CONFIG_PHYS_64BIT)
 407                writel(upper_32_bits((ulong)priv->rx_bd), &regs->upper_rxqbase);
 408#endif
 409
 410                /* Setup for DMA Configuration register */
 411                writel(ZYNQ_GEM_DMACR_INIT, &regs->dmacr);
 412
 413                /* Setup for Network Control register, MDIO, Rx and Tx enable */
 414                setbits_le32(&regs_mdio->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);
 415
 416                /* Disable the second priority queue */
 417                dummy_tx_bd->addr = 0;
 418#if defined(CONFIG_PHYS_64BIT)
 419                dummy_tx_bd->addr_hi = 0;
 420#endif
 421                dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
 422                                ZYNQ_GEM_TXBUF_LAST_MASK|
 423                                ZYNQ_GEM_TXBUF_USED_MASK;
 424
 425                dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
 426                                ZYNQ_GEM_RXBUF_NEW_MASK;
 427#if defined(CONFIG_PHYS_64BIT)
 428                dummy_rx_bd->addr_hi = 0;
 429#endif
 430                dummy_rx_bd->status = 0;
 431
 432                writel((ulong)dummy_tx_bd, &regs->transmit_q1_ptr);
 433                writel((ulong)dummy_rx_bd, &regs->receive_q1_ptr);
 434
 435                priv->init++;
 436        }
 437
 438        ret = phy_startup(priv->phydev);
 439        if (ret)
 440                return ret;
 441
 442        if (!priv->phydev->link) {
 443                printf("%s: No link.\n", priv->phydev->dev->name);
 444                return -1;
 445        }
 446
 447        nwconfig = ZYNQ_GEM_NWCFG_INIT;
 448
 449        /*
 450         * Set SGMII enable PCS selection only if internal PCS/PMA
 451         * core is used and interface is SGMII.
 452         */
 453        if (priv->interface == PHY_INTERFACE_MODE_SGMII &&
 454            priv->int_pcs) {
 455                nwconfig |= ZYNQ_GEM_NWCFG_SGMII_ENBL |
 456                            ZYNQ_GEM_NWCFG_PCS_SEL;
 457        }
 458
 459        switch (priv->phydev->speed) {
 460        case SPEED_1000:
 461                writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED1000,
 462                       &regs->nwcfg);
 463                clk_rate = ZYNQ_GEM_FREQUENCY_1000;
 464                break;
 465        case SPEED_100:
 466                writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED100,
 467                       &regs->nwcfg);
 468                clk_rate = ZYNQ_GEM_FREQUENCY_100;
 469                break;
 470        case SPEED_10:
 471                clk_rate = ZYNQ_GEM_FREQUENCY_10;
 472                break;
 473        }
 474
 475#ifdef CONFIG_ARM64
 476        if (priv->interface == PHY_INTERFACE_MODE_SGMII &&
 477            priv->int_pcs) {
 478                /*
 479                 * Disable AN for fixed link configuration, enable otherwise.
 480                 * Must be written after PCS_SEL is set in nwconfig,
 481                 * otherwise writes will not take effect.
 482                 */
 483                if (priv->phydev->phy_id != PHY_FIXED_ID)
 484                        writel(readl(&regs->pcscntrl) | ZYNQ_GEM_PCS_CTL_ANEG_ENBL,
 485                               &regs->pcscntrl);
 486                else
 487                        writel(readl(&regs->pcscntrl) & ~ZYNQ_GEM_PCS_CTL_ANEG_ENBL,
 488                               &regs->pcscntrl);
 489        }
 490#endif
 491
 492        ret = clk_set_rate(&priv->tx_clk, clk_rate);
 493        if (IS_ERR_VALUE(ret)) {
 494                dev_err(dev, "failed to set tx clock rate\n");
 495                return ret;
 496        }
 497
 498        ret = clk_enable(&priv->tx_clk);
 499        if (ret) {
 500                dev_err(dev, "failed to enable tx clock\n");
 501                return ret;
 502        }
 503
 504        if (priv->clk_en_info & RXCLK_EN) {
 505                ret = clk_enable(&priv->rx_clk);
 506                if (ret) {
 507                        dev_err(dev, "failed to enable rx clock\n");
 508                        return ret;
 509                }
 510        }
 511        setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
 512                                        ZYNQ_GEM_NWCTRL_TXEN_MASK);
 513
 514        return 0;
 515}
 516
 517static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
 518{
 519        dma_addr_t addr;
 520        u32 size;
 521        struct zynq_gem_priv *priv = dev_get_priv(dev);
 522        struct zynq_gem_regs *regs = priv->iobase;
 523        struct emac_bd *current_bd = &priv->tx_bd[1];
 524
 525        /* Setup Tx BD */
 526        memset(priv->tx_bd, 0, sizeof(struct emac_bd));
 527
 528        priv->tx_bd->addr = lower_32_bits((ulong)ptr);
 529#if defined(CONFIG_PHYS_64BIT)
 530        priv->tx_bd->addr_hi = upper_32_bits((ulong)ptr);
 531#endif
 532        priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
 533                               ZYNQ_GEM_TXBUF_LAST_MASK;
 534        /* Dummy descriptor to mark it as the last in descriptor chain */
 535        current_bd->addr = 0x0;
 536#if defined(CONFIG_PHYS_64BIT)
 537        current_bd->addr_hi = 0x0;
 538#endif
 539        current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
 540                             ZYNQ_GEM_TXBUF_LAST_MASK|
 541                             ZYNQ_GEM_TXBUF_USED_MASK;
 542
 543        /* setup BD */
 544        writel(lower_32_bits((ulong)priv->tx_bd), &regs->txqbase);
 545#if defined(CONFIG_PHYS_64BIT)
 546        writel(upper_32_bits((ulong)priv->tx_bd), &regs->upper_txqbase);
 547#endif
 548
 549        addr = (ulong) ptr;
 550        addr &= ~(ARCH_DMA_MINALIGN - 1);
 551        size = roundup(len, ARCH_DMA_MINALIGN);
 552        flush_dcache_range(addr, addr + size);
 553        barrier();
 554
 555        /* Start transmit */
 556        setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);
 557
 558        /* Read TX BD status */
 559        if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
 560                printf("TX buffers exhausted in mid frame\n");
 561
 562        return wait_for_bit_le32(&regs->txsr, ZYNQ_GEM_TSR_DONE,
 563                                 true, 20000, true);
 564}
 565
 566/* Do not check frame_recd flag in rx_status register 0x20 - just poll BD */
 567static int zynq_gem_recv(struct udevice *dev, int flags, uchar **packetp)
 568{
 569        int frame_len;
 570        dma_addr_t addr;
 571        struct zynq_gem_priv *priv = dev_get_priv(dev);
 572        struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
 573
 574        if (!(current_bd->addr & ZYNQ_GEM_RXBUF_NEW_MASK))
 575                return -1;
 576
 577        if (!(current_bd->status &
 578                        (ZYNQ_GEM_RXBUF_SOF_MASK | ZYNQ_GEM_RXBUF_EOF_MASK))) {
 579                printf("GEM: SOF or EOF not set for last buffer received!\n");
 580                return -1;
 581        }
 582
 583        frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK;
 584        if (!frame_len) {
 585                printf("%s: Zero size packet?\n", __func__);
 586                return -1;
 587        }
 588
 589#if defined(CONFIG_PHYS_64BIT)
 590        addr = (dma_addr_t)((current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK)
 591                      | ((dma_addr_t)current_bd->addr_hi << 32));
 592#else
 593        addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
 594#endif
 595        addr &= ~(ARCH_DMA_MINALIGN - 1);
 596
 597        *packetp = (uchar *)(uintptr_t)addr;
 598
 599        invalidate_dcache_range(addr, addr + roundup(PKTSIZE_ALIGN, ARCH_DMA_MINALIGN));
 600        barrier();
 601
 602        return frame_len;
 603}
 604
 605static int zynq_gem_free_pkt(struct udevice *dev, uchar *packet, int length)
 606{
 607        struct zynq_gem_priv *priv = dev_get_priv(dev);
 608        struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
 609        struct emac_bd *first_bd;
 610        dma_addr_t addr;
 611
 612        if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) {
 613                priv->rx_first_buf = priv->rxbd_current;
 614        } else {
 615                current_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
 616                current_bd->status = 0xF0000000; /* FIXME */
 617        }
 618
 619        if (current_bd->status & ZYNQ_GEM_RXBUF_EOF_MASK) {
 620                first_bd = &priv->rx_bd[priv->rx_first_buf];
 621                first_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
 622                first_bd->status = 0xF0000000;
 623        }
 624
 625        /* Flush the cache for the packet as well */
 626#if defined(CONFIG_PHYS_64BIT)
 627        addr = (dma_addr_t)((current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK)
 628                | ((dma_addr_t)current_bd->addr_hi << 32));
 629#else
 630        addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
 631#endif
 632        flush_dcache_range(addr, addr + roundup(PKTSIZE_ALIGN,
 633                                                ARCH_DMA_MINALIGN));
 634        barrier();
 635
 636        if ((++priv->rxbd_current) >= RX_BUF)
 637                priv->rxbd_current = 0;
 638
 639        return 0;
 640}
 641
 642static void zynq_gem_halt(struct udevice *dev)
 643{
 644        struct zynq_gem_priv *priv = dev_get_priv(dev);
 645        struct zynq_gem_regs *regs = priv->iobase;
 646
 647        clrsetbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
 648                                                ZYNQ_GEM_NWCTRL_TXEN_MASK, 0);
 649}
 650
 651__weak int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
 652{
 653        return -ENOSYS;
 654}
 655
 656static int zynq_gem_read_rom_mac(struct udevice *dev)
 657{
 658        struct eth_pdata *pdata = dev_get_plat(dev);
 659
 660        if (!pdata)
 661                return -ENOSYS;
 662
 663        return zynq_board_read_rom_ethaddr(pdata->enetaddr);
 664}
 665
 666static int zynq_gem_miiphy_read(struct mii_dev *bus, int addr,
 667                                int devad, int reg)
 668{
 669        struct zynq_gem_priv *priv = bus->priv;
 670        int ret;
 671        u16 val = 0;
 672
 673        ret = phyread(priv, addr, reg, &val);
 674        debug("%s 0x%x, 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, val, ret);
 675        return val;
 676}
 677
 678static int zynq_gem_miiphy_write(struct mii_dev *bus, int addr, int devad,
 679                                 int reg, u16 value)
 680{
 681        struct zynq_gem_priv *priv = bus->priv;
 682
 683        debug("%s 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, value);
 684        return phywrite(priv, addr, reg, value);
 685}
 686
 687static int zynq_gem_probe(struct udevice *dev)
 688{
 689        void *bd_space;
 690        struct zynq_gem_priv *priv = dev_get_priv(dev);
 691        int ret;
 692
 693        /* Align rxbuffers to ARCH_DMA_MINALIGN */
 694        priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
 695        if (!priv->rxbuffers)
 696                return -ENOMEM;
 697
 698        memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);
 699        ulong addr = (ulong)priv->rxbuffers;
 700        flush_dcache_range(addr, addr + roundup(RX_BUF * PKTSIZE_ALIGN, ARCH_DMA_MINALIGN));
 701        barrier();
 702
 703        /* Align bd_space to MMU_SECTION_SHIFT */
 704        bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
 705        if (!bd_space) {
 706                ret = -ENOMEM;
 707                goto err1;
 708        }
 709
 710        mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
 711                                        BD_SPACE, DCACHE_OFF);
 712
 713        /* Initialize the bd spaces for tx and rx bd's */
 714        priv->tx_bd = (struct emac_bd *)bd_space;
 715        priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);
 716
 717        ret = clk_get_by_name(dev, "tx_clk", &priv->tx_clk);
 718        if (ret < 0) {
 719                dev_err(dev, "failed to get tx_clock\n");
 720                goto err2;
 721        }
 722
 723        if (priv->clk_en_info & RXCLK_EN) {
 724                ret = clk_get_by_name(dev, "rx_clk", &priv->rx_clk);
 725                if (ret < 0) {
 726                        dev_err(dev, "failed to get rx_clock\n");
 727                        goto err2;
 728                }
 729        }
 730
 731        priv->bus = mdio_alloc();
 732        priv->bus->read = zynq_gem_miiphy_read;
 733        priv->bus->write = zynq_gem_miiphy_write;
 734        priv->bus->priv = priv;
 735
 736        ret = mdio_register_seq(priv->bus, dev_seq(dev));
 737        if (ret)
 738                goto err2;
 739
 740        ret = zynq_phy_init(dev);
 741        if (ret)
 742                goto err3;
 743
 744        return ret;
 745
 746err3:
 747        mdio_unregister(priv->bus);
 748err2:
 749        free(priv->tx_bd);
 750err1:
 751        free(priv->rxbuffers);
 752        return ret;
 753}
 754
 755static int zynq_gem_remove(struct udevice *dev)
 756{
 757        struct zynq_gem_priv *priv = dev_get_priv(dev);
 758
 759        free(priv->phydev);
 760        mdio_unregister(priv->bus);
 761        mdio_free(priv->bus);
 762
 763        return 0;
 764}
 765
 766static const struct eth_ops zynq_gem_ops = {
 767        .start                  = zynq_gem_init,
 768        .send                   = zynq_gem_send,
 769        .recv                   = zynq_gem_recv,
 770        .free_pkt               = zynq_gem_free_pkt,
 771        .stop                   = zynq_gem_halt,
 772        .write_hwaddr           = zynq_gem_setup_mac,
 773        .read_rom_hwaddr        = zynq_gem_read_rom_mac,
 774};
 775
 776static int zynq_gem_of_to_plat(struct udevice *dev)
 777{
 778        struct eth_pdata *pdata = dev_get_plat(dev);
 779        struct zynq_gem_priv *priv = dev_get_priv(dev);
 780        struct ofnode_phandle_args phandle_args;
 781        const char *phy_mode;
 782
 783        pdata->iobase = (phys_addr_t)dev_read_addr(dev);
 784        priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
 785        priv->mdiobase = priv->iobase;
 786        /* Hardcode for now */
 787        priv->phyaddr = -1;
 788
 789        if (!dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
 790                                        &phandle_args)) {
 791                fdt_addr_t addr;
 792                ofnode parent;
 793
 794                debug("phy-handle does exist %s\n", dev->name);
 795                priv->phyaddr = ofnode_read_u32_default(phandle_args.node,
 796                                                        "reg", -1);
 797                priv->phy_of_node = phandle_args.node;
 798                priv->max_speed = ofnode_read_u32_default(phandle_args.node,
 799                                                          "max-speed",
 800                                                          SPEED_1000);
 801
 802                parent = ofnode_get_parent(phandle_args.node);
 803                addr = ofnode_get_addr(parent);
 804                if (addr != FDT_ADDR_T_NONE) {
 805                        debug("MDIO bus not found %s\n", dev->name);
 806                        priv->mdiobase = (struct zynq_gem_regs *)addr;
 807                }
 808        }
 809
 810        phy_mode = dev_read_prop(dev, "phy-mode", NULL);
 811        if (phy_mode)
 812                pdata->phy_interface = phy_get_interface_by_name(phy_mode);
 813        if (pdata->phy_interface == -1) {
 814                debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
 815                return -EINVAL;
 816        }
 817        priv->interface = pdata->phy_interface;
 818
 819        priv->int_pcs = dev_read_bool(dev, "is-internal-pcspma");
 820
 821        printf("\nZYNQ GEM: %lx, mdio bus %lx, phyaddr %d, interface %s\n",
 822               (ulong)priv->iobase, (ulong)priv->mdiobase, priv->phyaddr,
 823               phy_string_for_interface(priv->interface));
 824
 825        priv->clk_en_info = dev_get_driver_data(dev);
 826
 827        return 0;
 828}
 829
 830static const struct udevice_id zynq_gem_ids[] = {
 831        { .compatible = "cdns,versal-gem", .data = RXCLK_EN },
 832        { .compatible = "cdns,zynqmp-gem" },
 833        { .compatible = "cdns,zynq-gem" },
 834        { .compatible = "cdns,gem" },
 835        { }
 836};
 837
 838U_BOOT_DRIVER(zynq_gem) = {
 839        .name   = "zynq_gem",
 840        .id     = UCLASS_ETH,
 841        .of_match = zynq_gem_ids,
 842        .of_to_plat = zynq_gem_of_to_plat,
 843        .probe  = zynq_gem_probe,
 844        .remove = zynq_gem_remove,
 845        .ops    = &zynq_gem_ops,
 846        .priv_auto      = sizeof(struct zynq_gem_priv),
 847        .plat_auto      = sizeof(struct eth_pdata),
 848};
 849