LXR uboot/include/configs/ge

   1/*
   2 * GE B1x5v2
   3 *
   4 * Copyright 2018-2020 GE Inc.
   5 * Copyright 2018-2020 Collabora Ltd.
   6 *
   7 * SPDX-License-Identifier:    GPL-2.0+
   8 */
   9
  10#ifndef __GE_B1X5V2_CONFIG_H
  11#define __GE_B1X5V2_CONFIG_H
  12
  13#include "mx6_common.h"
  14
  15#include "imx6_spl.h"
  16#define CONFIG_SPL_TARGET               "u-boot-with-spl.imx"
  17
  18/* Size of malloc() pool */
  19#define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  20
  21/* PWM */
  22#define CONFIG_IMX6_PWM_PER_CLK         66000000
  23
  24/* UART */
  25#define CONFIG_MXC_UART_BASE            UART3_BASE
  26
  27#if CONFIG_MXC_UART_BASE == UART2_BASE
  28/* UART2 requires CONFIG_DEBUG_UART_BASE=0x21e8000 */
  29#define CONSOLE_DEVICE "ttymxc1" /* System on Module debug connector */
  30#else
  31/* UART3 requires CONFIG_DEBUG_UART_BASE=0x21ec000 */
  32#define CONSOLE_DEVICE "ttymxc2" /* Base board debug connector */
  33#endif
  34
  35/* USB */
  36#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  37#define CONFIG_MXC_USB_PORTSC           (PORT_PTS_UTMI | PORT_PTS_PTW)
  38#define CONFIG_MXC_USB_FLAGS            0
  39#define CONFIG_USB_MAX_CONTROLLER_COUNT 2 /* Enabled USB controller number */
  40#define CONFIG_USBD_HS
  41
  42/* Video */
  43#define CONFIG_HIDE_LOGO_VERSION
  44#define CONFIG_IMX_VIDEO_SKIP
  45
  46/* Memory */
  47#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
  48
  49#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
  50#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
  51#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
  52
  53#define CONFIG_SYS_INIT_SP_OFFSET \
  54        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
  55#define CONFIG_SYS_INIT_SP_ADDR \
  56        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
  57
  58/* Command definition */
  59#define CONFIG_EXTRA_ENV_SETTINGS \
  60        "image=/boot/fitImage\0" \
  61        "fdt_addr_r=0x18000000\0" \
  62        "splash_addr_r=0x20000000\0" \
  63        "mmcdev=2\0" \
  64        "mmcpart=1\0" \
  65        "console=console="CONSOLE_DEVICE",115200\0" \
  66        "quiet=quiet loglevel=0\0" \
  67        "rootdev=/dev/mmcblk1p\0" \
  68        "setargs=setenv bootargs ${console} ${quiet} ${fsckforcerepair} " \
  69                "bootcause=${bootcause} vt.global_cursor_default=0 vt.cur_default=1 " \
  70                "root=${rootdev}${mmcpart} video=HDMI-A-1:${resolution} rootwait ro\0" \
  71        "loadimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
  72        "showsplashscreen=load mmc ${mmcdev}:${mmcpart} ${splash_addr_r} /boot/splashscreen-${resolution}.bmp; " \
  73                "bmp display ${splash_addr_r};\0" \
  74        "setconfidx=" \
  75                "if test \"${devicetype}\" = \"B105v2\"; then " \
  76                        "setenv confidx 1; " \
  77                "elif test \"${devicetype}\" = \"B125v2\"; then " \
  78                        "setenv confidx 2; " \
  79                "elif test \"${devicetype}\" = \"B155v2\"; then " \
  80                        "setenv confidx 3; " \
  81                "elif test \"${devicetype}\" = \"B105Pv2\"; then " \
  82                        "setenv confidx 4; " \
  83                "elif test \"${devicetype}\" = \"B125Pv2\"; then " \
  84                        "setenv confidx 5; " \
  85                "fi;\0" \
  86        "set_default_type=setenv devicetype B155v2; setenv resolution 1366x768;" \
  87                "setenv fdtfile imx6dl-b155v2.dtb; run setconfidx;\0" \
  88        "checkconfidx=env exists confidx || run set_default_type;\0" \
  89        "checkfsckforcerepair=" \
  90                "if test \"${bootcount}\" > \"3\" ; then " \
  91                        "setenv fsckforcerepair fsck.repair=1; " \
  92                "fi;\0" \
  93        "helix=run setconfidx; run checkconfidx; run checkfsckforcerepair; run setargs; " \
  94                "regulator dev LED_VCC; regulator enable; " \
  95                "regulator dev 5V0_AUDIO; regulator enable; " \
  96                "bootm ${loadaddr}#conf@${confidx};\0" \
  97        "failbootcmd=" \
  98                "echo reached failbootcmd;" \
  99                "cls; setcurs 5 4; " \
 100                "lcdputs \"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
 101                "bootcount reset; \0" \
 102        "hasfirstboot=" \
 103                "load mmc ${mmcdev}:${mmcpart} ${loadaddr} " \
 104                "/boot/bootcause/firstboot;\0" \
 105        "swappartitions=" \
 106                "setexpr mmcpart 3 - ${mmcpart};\0" \
 107        "doboot=" \
 108                "echo Booting from mmc:${mmcdev}:${mmcpart} ...; " \
 109                "run helix;\0" \
 110        "altbootcmd=" \
 111                "setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
 112                "run hasfirstboot || setenv mmcpart 0; " \
 113                "if test ${mmcpart} != 0; then " \
 114                        "setenv bootcause REVERT; " \
 115                        "run swappartitions loadimage doboot; " \
 116                "fi; " \
 117                "run failbootcmd\0" \
 118        "tryboot=" \
 119                "setenv mmcpart 1; run hasfirstboot || setenv mmcpart 2; " \
 120                "run loadimage || run swappartitions && run loadimage || " \
 121                "setenv mmcpart 0 && echo MISSING IMAGE;" \
 122                "run showsplashscreen; sleep 1; " \
 123                "run doboot; run failbootcmd;\0" \
 124
 125#define CONFIG_BOOTCOMMAND "run tryboot;"
 126
 127#endif /* __GE_B1X5V2_CONFIG_H */
 128