// SPDX-License-Identifier: GPL-2.0+
/*
 * (C) Copyright 2012-2013
 * Texas Instruments, <www.ti.com>
 */
#include <config.h>
#include <palmas.h>

void palmas_init_settings(void)
{
#ifdef CONFIG_PALMAS_SMPS7_FPWM
        int err;
        /*
         * Set SMPS7 (1.8 V I/O supply on platforms with TWL6035/37) to
         * forced PWM mode. This reduces noise (but affects efficiency).
         */
        u8 val = SMPS_MODE_SLP_FPWM | SMPS_MODE_ACT_FPWM;
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS7_CTRL, val);
        if (err)
                printf("palmas: could not force PWM for SMPS7: err = %d\n",
                       err);
#endif
}

#if defined(CONFIG_OMAP54XX)
int lp873x_mmc1_poweron_ldo(uint voltage)
{
        if (palmas_i2c_write_u8(LP873X_LDO1_ADDR, LP873X_LDO1_VOLTAGE,
                                voltage)) {
                printf("lp873x: could not set LDO1 voltage.\n");
                return 1;
        }
        /* TURN ON LDO1 */
        if (palmas_i2c_write_u8(LP873X_LDO1_ADDR, LP873X_LDO1_CTRL,
                                LP873X_LDO_CTRL_EN | LP873X_LDO_CTRL_RDIS_EN)) {
                printf("lp873x: could not turn on LDO1.\n");
                return 1;
        }
        return 0;

}
#endif

int palmas_mmc1_poweron_ldo(uint ldo_volt, uint ldo_ctrl, uint voltage)
{
        u8 val = 0;

#if defined(CONFIG_DRA7XX)
        int ret;

        ret = palmas_i2c_write_u8(TPS65903X_CHIP_P1, ldo_volt, voltage);
        if (ret) {
                printf("tps65903x: could not set LDO1 voltage.\n");
                return ret;
        }
        /* TURN ON LDO1 */
        val = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
        ret = palmas_i2c_write_u8(TPS65903X_CHIP_P1, ldo_ctrl, val);
        if (ret) {
                printf("tps65903x: could not turn on LDO1.\n");
                return ret;
        }
        return 0;
#else
        /*
         * We assume that this is a OMAP543X + TWL603X board:
         * Set TWL6035/37 LDO9 to 3.0 V
         */
        val = LDO_VOLT_3V0;
        return twl603x_mmc1_set_ldo9(val);
#endif
}

/*
 * On some OMAP5 + TWL603X hardware the SD card socket and LDO9_IN are
 * powered by an external 3.3 V regulator, while the output of LDO9
 * supplies VDDS_SDCARD for the OMAP5 interface only. This implies that
 * LDO9 could be set to 'bypass' mode when required (e.g. for 3.3 V cards).
 */
int twl603x_mmc1_set_ldo9(u8 vsel)
{
        u8 cval = 0, vval = 0;  /* Off by default */
        int err;

        if (vsel) {
                /* Turn on */
                if (vsel > LDO_VOLT_3V3) {
                        /* Put LDO9 in bypass */
                        cval = LDO9_BYP_EN | RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
                        vval = LDO_VOLT_3V3;
                } else {
                        cval = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
                        vval = vsel & 0x3f;
                }
        }
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_VOLTAGE, vval);
        if (err) {
                printf("twl603x: could not set LDO9 %s: err = %d\n",
                       vsel > LDO_VOLT_3V3 ? "bypass" : "voltage", err);
                return err;
        }
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_CTRL, cval);
        if (err)
                printf("twl603x: could not turn %s LDO9: err = %d\n",
                       cval ? "on" : "off", err);
        return err;
}

#ifdef CONFIG_PALMAS_AUDPWR
/*
 * Turn audio codec power and 32 kHz clock on/off. Use for
 * testing OMAP543X + TWL603X + TWL604X boards only.
 */
int twl603x_audio_power(u8 on)
{
        u8 cval = 0, vval = 0, c32k = 0;
        int err;

        if (on) {
                vval = SMPS_VOLT_2V1;
                cval = SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO;
                c32k = RSC_MODE_SLEEP | RSC_MODE_ACTIVE;
        }
        /* Set SMPS9 to 2.1 V (for TWL604x), or to 0 (off) */
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_VOLTAGE, vval);
        if (err) {
                printf("twl603x: could not set SMPS9 voltage: err = %d\n",
                       err);
                return err;
        }
        /* Turn on or off SMPS9 */
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_CTRL, cval);
        if (err) {
                printf("twl603x: could not turn SMPS9 %s: err = %d\n",
                       cval ? "on" : "off", err);
                return err;
        }
        /* Output 32 kHz clock on or off */
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, CLK32KGAUDIO_CTRL, c32k);
        if (err)
                printf("twl603x: could not turn CLK32KGAUDIO %s: err = %d\n",
                       c32k ? "on" : "off", err);
        return err;
}
#endif

#ifdef CONFIG_PALMAS_USB_SS_PWR
/**
 * @brief palmas_enable_ss_ldo - Configure EVM board specific configurations
 * for the USB Super speed SMPS10 regulator.
 *
 * Return: 0
 */
int palmas_enable_ss_ldo(void)
{
        /* Enable smps10 regulator  */
        return palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS10_CTRL,
                                SMPS10_MODE_ACTIVE_D);
}
#endif

/*
 * Enable/disable back-up battery (or super cap) charging on TWL6035/37.
 * Please use defined BB_xxx values.
 */
int twl603x_enable_bb_charge(u8 bb_fields)
{
        u8 val = bb_fields & 0x0f;
        int err;

        val |= (VRTC_EN_SLP | VRTC_EN_OFF | VRTC_PWEN);
        err = palmas_i2c_write_u8(TWL603X_CHIP_P1, BB_VRTC_CTRL, val);
        if (err)
                printf("twl603x: could not set BB_VRTC_CTRL to 0x%02x: err = %d\n",
                       val, err);
        return err;
}

#if CONFIG_IS_ENABLED(DM_I2C)
int palmas_i2c_write_u8(u8 chip_no, u8 reg, u8 val)
{
        struct udevice *dev;
        int ret;

        ret = i2c_get_chip_for_busnum(0, chip_no, 1, &dev);
        if (ret) {
                pr_err("unable to get I2C bus. ret %d\n", ret);
                return ret;
        }
        ret = dm_i2c_reg_write(dev, reg, val);
        if (ret) {
                pr_err("writing to palmas failed. ret %d\n", ret);
                return ret;
        }
        return 0;
}

int palmas_i2c_read_u8(u8 chip_no, u8 reg, u8 *valp)
{
        struct udevice *dev;
        int ret;

        ret = i2c_get_chip_for_busnum(0, chip_no, 1, &dev);
        if (ret) {
                pr_err("unable to get I2C bus. ret %d\n", ret);
                return ret;
        }
        ret = dm_i2c_reg_read(dev, reg);
        if (ret < 0) {
                pr_err("reading from palmas failed. ret %d\n", ret);
                return ret;
        }
        *valp = (u8)ret;
        return 0;
}
#endif