LXR uboot/board/freescale/ls1043aqds/ddr.c

   1/*
   2 * Copyright 2015 Freescale Semiconductor, Inc.
   3 *
   4 * SPDX-License-Identifier:     GPL-2.0+
   5 */
   6
   7#include <common.h>
   8#include <fsl_ddr_sdram.h>
   9#include <fsl_ddr_dimm_params.h>
  10#ifdef CONFIG_FSL_DEEP_SLEEP
  11#include <fsl_sleep.h>
  12#endif
  13#include "ddr.h"
  14
  15DECLARE_GLOBAL_DATA_PTR;
  16
  17void fsl_ddr_board_options(memctl_options_t *popts,
  18                           dimm_params_t *pdimm,
  19                           unsigned int ctrl_num)
  20{
  21        const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
  22        ulong ddr_freq;
  23
  24        if (ctrl_num > 3) {
  25                printf("Not supported controller number %d\n", ctrl_num);
  26                return;
  27        }
  28        if (!pdimm->n_ranks)
  29                return;
  30
  31        pbsp = udimms[0];
  32
  33        /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
  34         * freqency and n_banks specified in board_specific_parameters table.
  35         */
  36        ddr_freq = get_ddr_freq(0) / 1000000;
  37        while (pbsp->datarate_mhz_high) {
  38                if (pbsp->n_ranks == pdimm->n_ranks) {
  39                        if (ddr_freq <= pbsp->datarate_mhz_high) {
  40                                popts->clk_adjust = pbsp->clk_adjust;
  41                                popts->wrlvl_start = pbsp->wrlvl_start;
  42                                popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  43                                popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  44                                popts->cpo_override = pbsp->cpo_override;
  45                                popts->write_data_delay =
  46                                        pbsp->write_data_delay;
  47                                goto found;
  48                        }
  49                        pbsp_highest = pbsp;
  50                }
  51                pbsp++;
  52        }
  53
  54        if (pbsp_highest) {
  55                printf("Error: board specific timing not found for %lu MT/s\n",
  56                       ddr_freq);
  57                printf("Trying to use the highest speed (%u) parameters\n",
  58                       pbsp_highest->datarate_mhz_high);
  59                popts->clk_adjust = pbsp_highest->clk_adjust;
  60                popts->wrlvl_start = pbsp_highest->wrlvl_start;
  61                popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
  62                popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
  63        } else {
  64                panic("DIMM is not supported by this board");
  65        }
  66found:
  67        debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
  68              pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
  69
  70        /* force DDR bus width to 32 bits */
  71        popts->data_bus_width = 1;
  72        popts->otf_burst_chop_en = 0;
  73        popts->burst_length = DDR_BL8;
  74        popts->bstopre = 0;             /* enable auto precharge */
  75
  76        /*
  77         * Factors to consider for half-strength driver enable:
  78         *      - number of DIMMs installed
  79         */
  80        popts->half_strength_driver_enable = 1;
  81        /*
  82         * Write leveling override
  83         */
  84        popts->wrlvl_override = 1;
  85        popts->wrlvl_sample = 0xf;
  86
  87        /*
  88         * Rtt and Rtt_WR override
  89         */
  90        popts->rtt_override = 0;
  91
  92        /* Enable ZQ calibration */
  93        popts->zq_en = 1;
  94
  95#ifdef CONFIG_SYS_FSL_DDR4
  96        popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
  97        popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
  98                          DDR_CDR2_VREF_OVRD(70);       /* Vref = 70% */
  99
 100        /* optimize cpo for erratum A-009942 */
 101        popts->cpo_sample = 0x59;
 102#else
 103        popts->cswl_override = DDR_CSWL_CS0;
 104
 105        /* DHC_EN =1, ODT = 75 Ohm */
 106        popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
 107        popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
 108#endif
 109}
 110
 111phys_size_t initdram(int board_type)
 112{
 113        phys_size_t dram_size;
 114
 115#if defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD)
 116        return fsl_ddr_sdram_size();
 117#else
 118        puts("Initializing DDR....using SPD\n");
 119
 120        dram_size = fsl_ddr_sdram();
 121#endif
 122        erratum_a008850_post();
 123
 124#ifdef CONFIG_FSL_DEEP_SLEEP
 125        fsl_dp_ddr_restore();
 126#endif
 127
 128        return dram_size;
 129}
 130
 131void dram_init_banksize(void)
 132{
 133        /*
 134         * gd->arch.secure_ram tracks the location of secure memory.
 135         * It was set as if the memory starts from 0.
 136         * The address needs to add the offset of its bank.
 137         */
 138        gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
 139        if (gd->ram_size > CONFIG_SYS_DDR_BLOCK1_SIZE) {
 140                gd->bd->bi_dram[0].size = CONFIG_SYS_DDR_BLOCK1_SIZE;
 141                gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
 142                gd->bd->bi_dram[1].size = gd->ram_size -
 143                                          CONFIG_SYS_DDR_BLOCK1_SIZE;
 144#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 145                gd->arch.secure_ram = gd->bd->bi_dram[1].start +
 146                                      gd->arch.secure_ram -
 147                                      CONFIG_SYS_DDR_BLOCK1_SIZE;
 148                gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 149#endif
 150        } else {
 151                gd->bd->bi_dram[0].size = gd->ram_size;
 152#ifdef CONFIG_SYS_MEM_RESERVE_SECURE
 153                gd->arch.secure_ram = gd->bd->bi_dram[0].start +
 154                                      gd->arch.secure_ram;
 155                gd->arch.secure_ram |= MEM_RESERVE_SECURE_MAINTAINED;
 156#endif
 157        }
 158}
 159