LXR uboot/include/configs/advantech

   1/*
   2 * Copyright (C) 2016 Timesys Corporation
   3 * Copyright (C) 2016 Advantech Corporation
   4 * Copyright (C) 2012 Freescale Semiconductor, Inc.
   5 *
   6 * SPDX-License-Identifier:     GPL-2.0+
   7 */
   8
   9#ifndef __ADVANTECH_DMSBA16_CONFIG_H
  10#define __ADVANTECH_DMSBA16_CONFIG_H
  11
  12#include <asm/arch/imx-regs.h>
  13#include <asm/imx-common/gpio.h>
  14
  15#define CONFIG_BOARD_NAME       "Advantech DMS-BA16"
  16
  17#define CONFIG_MXC_UART_BASE    UART4_BASE
  18#define CONSOLE_DEV     "ttymxc3"
  19#define CONFIG_EXTRA_BOOTARGS   "panic=10"
  20
  21#define CONFIG_BOOT_DIR ""
  22#define CONFIG_LOADCMD "fatload"
  23#define CONFIG_RFSPART "2"
  24
  25#define CONFIG_SUPPORT_EMMC_BOOT
  26
  27#include "mx6_common.h"
  28#include <linux/sizes.h>
  29
  30#define CONFIG_CMDLINE_TAG
  31#define CONFIG_SETUP_MEMORY_TAGS
  32#define CONFIG_INITRD_TAG
  33#define CONFIG_REVISION_TAG
  34#define CONFIG_SYS_MALLOC_LEN           (10 * SZ_1M)
  35
  36#define CONFIG_BOARD_EARLY_INIT_F
  37#define CONFIG_BOARD_LATE_INIT
  38
  39#define CONFIG_MXC_GPIO
  40#define CONFIG_MXC_UART
  41
  42#define CONFIG_CMD_FUSE
  43#define CONFIG_MXC_OCOTP
  44
  45/* SATA Configs */
  46#define CONFIG_CMD_SATA
  47#define CONFIG_DWC_AHSATA
  48#define CONFIG_SYS_SATA_MAX_DEVICE      1
  49#define CONFIG_DWC_AHSATA_PORT_ID       0
  50#define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  51#define CONFIG_LBA48
  52#define CONFIG_LIBATA
  53
  54/* MMC Configs */
  55#define CONFIG_FSL_ESDHC
  56#define CONFIG_FSL_USDHC
  57#define CONFIG_SYS_FSL_ESDHC_ADDR      0
  58#define CONFIG_GENERIC_MMC
  59#define CONFIG_BOUNCE_BUFFER
  60#define CONFIG_DOS_PARTITION
  61
  62/* USB Configs */
  63#define CONFIG_USB_EHCI
  64#define CONFIG_USB_EHCI_MX6
  65#define CONFIG_USB_STORAGE
  66#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
  67#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  68#define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
  69#define CONFIG_MXC_USB_FLAGS    0
  70#define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
  71
  72#define CONFIG_USBD_HS
  73#define CONFIG_USB_FUNCTION_MASS_STORAGE
  74#define CONFIG_USB_GADGET_VBUS_DRAW 2
  75
  76/* Networking Configs */
  77#define CONFIG_FEC_MXC
  78#define CONFIG_MII
  79#define IMX_FEC_BASE                    ENET_BASE_ADDR
  80#define CONFIG_FEC_XCV_TYPE             RGMII
  81#define CONFIG_ETHPRIME         "FEC"
  82#define CONFIG_FEC_MXC_PHYADDR          4
  83#define CONFIG_PHYLIB
  84#define CONFIG_PHY_ATHEROS
  85
  86/* Serial Flash */
  87#ifdef CONFIG_CMD_SF
  88#define CONFIG_MXC_SPI
  89#define CONFIG_SF_DEFAULT_BUS           0
  90#define CONFIG_SF_DEFAULT_CS            0
  91#define CONFIG_SF_DEFAULT_SPEED 20000000
  92#define CONFIG_SF_DEFAULT_MODE          SPI_MODE_0
  93#endif
  94
  95/* allow to overwrite serial and ethaddr */
  96#define CONFIG_ENV_OVERWRITE
  97#define CONFIG_CONS_INDEX       1
  98#define CONFIG_BAUDRATE 115200
  99
 100/* Command definition */
 101#define CONFIG_CMD_BMODE
 102
 103#define CONFIG_LOADADDR 0x12000000
 104#define CONFIG_SYS_TEXT_BASE    0x17800000
 105
 106#define CONFIG_EXTRA_ENV_SETTINGS \
 107        "script=boot.scr\0" \
 108        "image=" CONFIG_BOOT_DIR "/uImage\0" \
 109        "uboot=u-boot.imx\0" \
 110        "fdt_file=" CONFIG_BOOT_DIR "/" CONFIG_DEFAULT_FDT_FILE "\0" \
 111        "fdt_addr=0x18000000\0" \
 112        "boot_fdt=yes\0" \
 113        "ip_dyn=yes\0" \
 114        "console=" CONSOLE_DEV "\0" \
 115        "fdt_high=0xffffffff\0"   \
 116        "initrd_high=0xffffffff\0" \
 117        "sddev=0\0" \
 118        "emmcdev=1\0" \
 119        "partnum=1\0" \
 120        "loadcmd=" CONFIG_LOADCMD "\0" \
 121        "rfspart=" CONFIG_RFSPART "\0" \
 122        "update_sd_firmware=" \
 123                "if test ${ip_dyn} = yes; then " \
 124                        "setenv get_cmd dhcp; " \
 125                "else " \
 126                        "setenv get_cmd tftp; " \
 127                "fi; " \
 128                "if mmc dev ${mmcdev}; then "   \
 129                        "if ${get_cmd} ${update_sd_firmware_filename}; then " \
 130                                "setexpr fw_sz ${filesize} / 0x200; " \
 131                                "setexpr fw_sz ${fw_sz} + 1; "  \
 132                                "mmc write ${loadaddr} 0x2 ${fw_sz}; " \
 133                        "fi; "  \
 134                "fi\0" \
 135        "update_sf_uboot=" \
 136                "if tftp $loadaddr $uboot; then " \
 137                        "sf probe; " \
 138                        "sf erase 0 0xC0000; " \
 139                        "sf write $loadaddr 0x400 $filesize; " \
 140                        "echo 'U-Boot upgraded. Please reset'; " \
 141                "fi\0" \
 142        "setargs=setenv bootargs console=${console},${baudrate} " \
 143                "root=/dev/${rootdev} rw rootwait " CONFIG_EXTRA_BOOTARGS "\0" \
 144        "loadbootscript=" \
 145                "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${script};\0" \
 146        "bootscript=echo Running bootscript from ${dev}:${devnum}:${partnum};" \
 147                " source\0" \
 148        "loadimage=" \
 149                "${loadcmd} ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
 150        "loadfdt=${loadcmd} ${dev} ${devnum}:${partnum} ${fdt_addr} ${fdt_file}\0" \
 151        "tryboot=" \
 152                "if run loadbootscript; then " \
 153                        "run bootscript; " \
 154                "else " \
 155                        "if run loadimage; then " \
 156                                "run doboot; " \
 157                        "fi; " \
 158                "fi;\0" \
 159        "doboot=echo Booting from ${dev}:${devnum}:${partnum} ...; " \
 160                "run setargs; " \
 161                "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 162                        "if run loadfdt; then " \
 163                                "bootm ${loadaddr} - ${fdt_addr}; " \
 164                        "else " \
 165                                "if test ${boot_fdt} = try; then " \
 166                                        "bootm; " \
 167                                "else " \
 168                                        "echo WARN: Cannot load the DT; " \
 169                                "fi; " \
 170                        "fi; " \
 171                "else " \
 172                        "bootm; " \
 173                "fi;\0" \
 174        "netargs=setenv bootargs console=${console},${baudrate} " \
 175                "root=/dev/nfs " \
 176                "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 177        "netboot=echo Booting from net ...; " \
 178                "run netargs; " \
 179                "if test ${ip_dyn} = yes; then " \
 180                        "setenv get_cmd dhcp; " \
 181                "else " \
 182                        "setenv get_cmd tftp; " \
 183                "fi; " \
 184                "${get_cmd} ${image}; " \
 185                "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 186                        "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 187                                "bootm ${loadaddr} - ${fdt_addr}; " \
 188                        "else " \
 189                                "if test ${boot_fdt} = try; then " \
 190                                        "bootm; " \
 191                                "else " \
 192                                        "echo WARN: Cannot load the DT; " \
 193                                "fi; " \
 194                        "fi; " \
 195                "else " \
 196                        "bootm; " \
 197                "fi;\0" \
 198
 199#define CONFIG_BOOTCOMMAND \
 200        "usb start; " \
 201        "setenv dev usb; " \
 202        "setenv devnum 0; " \
 203        "setenv rootdev sda${rfspart}; " \
 204        "run tryboot; " \
 205        \
 206        "setenv dev mmc; " \
 207        "setenv rootdev mmcblk0p${rfspart}; " \
 208        \
 209        "setenv devnum ${sddev}; " \
 210        "if mmc dev ${devnum}; then " \
 211                "run tryboot; " \
 212        "fi; " \
 213        \
 214        "setenv devnum ${emmcdev}; " \
 215        "setenv rootdev mmcblk${emmcdev}p${rfspart}; " \
 216        "if mmc dev ${devnum}; then " \
 217                "run tryboot; " \
 218        "fi; " \
 219        \
 220        "bmode usb; " \
 221
 222#define CONFIG_ARP_TIMEOUT     200UL
 223
 224/* Miscellaneous configurable options */
 225#define CONFIG_SYS_LONGHELP
 226#define CONFIG_AUTO_COMPLETE
 227
 228/* Print Buffer Size */
 229#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 230#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 231
 232#define CONFIG_SYS_MEMTEST_START       0x10000000
 233#define CONFIG_SYS_MEMTEST_END         0x10010000
 234#define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 235
 236#define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 237
 238#define CONFIG_CMDLINE_EDITING
 239#define CONFIG_STACKSIZE               (128 * 1024)
 240
 241/* Physical Memory Map */
 242#define CONFIG_NR_DRAM_BANKS           1
 243#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 244
 245#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 246#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 247#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 248
 249#define CONFIG_SYS_INIT_SP_OFFSET \
 250        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 251#define CONFIG_SYS_INIT_SP_ADDR \
 252        (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 253
 254/* FLASH and environment organization */
 255#define CONFIG_SYS_NO_FLASH
 256
 257#define CONFIG_ENV_IS_IN_SPI_FLASH
 258#define CONFIG_ENV_SIZE                 (8 * 1024)
 259#define CONFIG_ENV_OFFSET               (768 * 1024)
 260#define CONFIG_ENV_SECT_SIZE            (64 * 1024)
 261#define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 262#define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 263#define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 264#define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 265
 266#ifndef CONFIG_SYS_DCACHE_OFF
 267#endif
 268
 269#define CONFIG_SYS_FSL_USDHC_NUM        3
 270
 271/* Framebuffer */
 272#define CONFIG_VIDEO_IPUV3
 273#define CONFIG_VIDEO_BMP_RLE8
 274#define CONFIG_SPLASH_SCREEN
 275#define CONFIG_SPLASH_SCREEN_ALIGN
 276#define CONFIG_BMP_16BPP
 277#define CONFIG_VIDEO_LOGO
 278#define CONFIG_VIDEO_BMP_LOGO
 279#define CONFIG_IPUV3_CLK                260000000
 280#define CONFIG_IMX_HDMI
 281#define CONFIG_IMX_VIDEO_SKIP
 282
 283#define CONFIG_PWM_IMX
 284#define CONFIG_IMX6_PWM_PER_CLK         66000000
 285
 286#undef CONFIG_CMD_PCI
 287#ifdef CONFIG_CMD_PCI
 288#define CONFIG_PCI_SCAN_SHOW
 289#define CONFIG_PCIE_IMX
 290#define CONFIG_PCIE_IMX_PERST_GPIO      IMX_GPIO_NR(7, 12)
 291#define CONFIG_PCIE_IMX_POWER_GPIO      IMX_GPIO_NR(1, 5)
 292#endif
 293
 294/* I2C Configs */
 295#define CONFIG_SYS_I2C
 296#define CONFIG_SYS_I2C_MXC
 297#define CONFIG_SYS_I2C_SPEED            100000
 298#define CONFIG_SYS_I2C_MXC_I2C1
 299#define CONFIG_SYS_I2C_MXC_I2C2
 300#define CONFIG_SYS_I2C_MXC_I2C3
 301
 302#endif  /* __ADVANTECH_DMSBA16_CONFIG_H */
 303