LXR uboot/include/configs/dragonboard410c.h

   1/*
   2 * Board configuration file for Dragonboard 410C
   3 *
   4 * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
   5 *
   6 * SPDX-License-Identifier:     GPL-2.0+
   7 */
   8
   9#ifndef __CONFIGS_DRAGONBOARD410C_H
  10#define __CONFIGS_DRAGONBOARD410C_H
  11
  12#include <linux/sizes.h>
  13#include <asm/arch/sysmap-apq8016.h>
  14
  15#define CONFIG_MISC_INIT_R /* To stop autoboot */
  16
  17/* Physical Memory Map */
  18#define CONFIG_NR_DRAM_BANKS            1
  19#define PHYS_SDRAM_1                    0x80000000
  20/* 1008 MB (the last ~30Mb are secured for TrustZone by ATF*/
  21#define PHYS_SDRAM_1_SIZE               0x3da00000
  22#define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
  23#define CONFIG_SYS_TEXT_BASE            0x80080000
  24#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
  25#define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x80000)
  26#define CONFIG_SYS_BOOTM_LEN            0x1000000 /* 16MB max kernel size */
  27
  28/* UART */
  29#define CONFIG_BAUDRATE                 115200
  30
  31/* Generic Timer Definitions */
  32#define COUNTER_FREQUENCY               19000000
  33
  34/* This are needed to have proper mmc support */
  35#define CONFIG_GENERIC_MMC
  36
  37#define CONFIG_SYS_LDSCRIPT "board/qualcomm/dragonboard410c/u-boot.lds"
  38
  39/* Fixup - in init code we switch from device to host mode,
  40 * it has to be done after each HCD reset */
  41#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
  42
  43#define CONFIG_USB_HOST_ETHER /* Enable USB Networking */
  44
  45/* Support all possible USB ethernet dongles */
  46#define CONFIG_USB_ETHER_DM9601
  47#define CONFIG_USB_ETHER_ASIX
  48#define CONFIG_USB_ETHER_ASIX88179
  49#define CONFIG_USB_ETHER_MCS7830
  50#define CONFIG_USB_ETHER_SMSC95XX
  51
  52/* Libraries  */
  53#define CONFIG_MD5
  54
  55/* Extra Commands */
  56#define CONFIG_CMD_ENV
  57#define CONFIG_CMD_GPT
  58#define CONFIG_CMD_MD5SUM
  59/* Enable that for switching of boot partitions */
  60/* Disabled by default as some sub-commands can brick eMMC */
  61/*#define CONFIG_SUPPORT_EMMC_BOOT */
  62#define CONFIG_CMD_PART
  63#define CONFIG_CMD_REGINFO      /* Register dump                */
  64#define CONFIG_CMD_TFTP
  65#define CONFIG_CMD_UNZIP
  66
  67/* Partition table support */
  68#define HAVE_BLOCK_DEVICE /* Needed for partition commands */
  69#define CONFIG_PARTITION_UUIDS
  70
  71#include <config_distro_defaults.h>
  72
  73/* BOOTP options */
  74#define CONFIG_BOOTP_BOOTFILESIZE
  75
  76/* Environment - Boot*/
  77#define CONFIG_BOOTARGS "console=ttyMSM0,115200n8"
  78
  79#define BOOT_TARGET_DEVICES(func) \
  80        func(USB, usb, 0) \
  81        func(MMC, mmc, 1) \
  82        func(MMC, mmc, 0) \
  83        func(DHCP, dhcp, na)
  84
  85#include <config_distro_bootcmd.h>
  86
  87/* Does what recovery does */
  88#define REFLASH(file, part) \
  89"part start mmc 0 "#part" start && "\
  90"part size mmc 0 "#part" size && "\
  91"tftp $loadaddr "#file" && " \
  92"mmc write $loadaddr $start $size && "
  93
  94#define CONFIG_ENV_REFLASH \
  95"mmc dev 0 && "\
  96"usb start && "\
  97"dhcp && "\
  98"tftp $loadaddr dragonboard/rescue/gpt_both0.bin && "\
  99"mmc write $loadaddr 0 43 && " \
 100"mmc rescan && "\
 101REFLASH(dragonboard/rescue/NON-HLOS.bin, 1)\
 102REFLASH(dragonboard/rescue/sbl1.mbn, 2)\
 103REFLASH(dragonboard/rescue/rpm.mbn, 3)\
 104REFLASH(dragonboard/rescue/tz.mbn, 4)\
 105REFLASH(dragonboard/rescue/hyp.mbn, 5)\
 106REFLASH(dragonboard/rescue/sec.dat, 6)\
 107REFLASH(dragonboard/rescue/emmc_appsboot.mbn, 7)\
 108REFLASH(dragonboard/u-boot.img, 8)\
 109"usb stop &&"\
 110"echo Reflash completed"
 111
 112/* Environment */
 113#define CONFIG_EXTRA_ENV_SETTINGS \
 114        "reflash="CONFIG_ENV_REFLASH"\0"\
 115        "loadaddr=0x81000000\0" \
 116        "fdt_high=0xffffffffffffffff\0" \
 117        "initrd_high=0xffffffffffffffff\0" \
 118        "linux_image=Image\0" \
 119        "kernel_addr_r=0x81000000\0"\
 120        "fdtfile=apq8016-sbc.dtb\0" \
 121        "fdt_addr_r=0x83000000\0"\
 122        "ramdisk_addr_r=0x84000000\0"\
 123        "scriptaddr=0x90000000\0"\
 124        "pxefile_addr_r=0x90100000\0"\
 125        BOOTENV
 126
 127#define CONFIG_ENV_IS_NOWHERE
 128#define CONFIG_ENV_SIZE                 0x2000
 129#define CONFIG_ENV_VARS_UBOOT_CONFIG
 130#define CONFIG_SYS_NO_FLASH
 131
 132/* Size of malloc() pool */
 133#define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + SZ_8M)
 134
 135/* Monitor Command Prompt */
 136#define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 137#define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 138                                        sizeof(CONFIG_SYS_PROMPT) + 16)
 139#define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 140#define CONFIG_SYS_MAXARGS              64      /* max command args */
 141
 142#endif
 143