LXR uboot/board/freescale/mpc5121ads/mpc5121ads.c

   1/*
   2 * (C) Copyright 2007-2009 DENX Software Engineering
   3 *
   4 * SPDX-License-Identifier:     GPL-2.0+
   5 */
   6
   7#include <common.h>
   8#include <asm/bitops.h>
   9#include <command.h>
  10#include <asm/io.h>
  11#include <asm/processor.h>
  12#include <asm/mpc512x.h>
  13#include <fdt_support.h>
  14#ifdef CONFIG_MISC_INIT_R
  15#include <i2c.h>
  16#endif
  17#include <net.h>
  18
  19#include <linux/mtd/mtd.h>
  20#include <linux/mtd/nand.h>
  21
  22DECLARE_GLOBAL_DATA_PTR;
  23
  24void __mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip);
  25
  26/* Active chip number set in board_nand_select_device() (mpc5121_nfc.c) */
  27extern int mpc5121_nfc_chip;
  28
  29/* Control chips select signal on MPC5121ADS board */
  30void mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip)
  31{
  32        unsigned char *csreg = (u8 *)CONFIG_SYS_CPLD_BASE + 0x09;
  33        u8 v;
  34
  35        v = in_8(csreg);
  36        v |= 0x0F;
  37
  38        if (chip >= 0) {
  39                __mpc5121_nfc_select_chip(mtd, 0);
  40                v &= ~(1 << mpc5121_nfc_chip);
  41        } else {
  42                __mpc5121_nfc_select_chip(mtd, -1);
  43        }
  44
  45        out_8(csreg, v);
  46}
  47
  48int board_early_init_f(void)
  49{
  50        /*
  51         * Disable Boot NOR FLASH write protect - CPLD Reg 8 NOR FLASH Control
  52         *
  53         * Without this the flash identification routine fails, as it needs to issue
  54         * write commands in order to establish the device ID.
  55         */
  56
  57#ifdef CONFIG_MPC5121ADS_REV2
  58        out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0xC1);
  59#else
  60        if (in_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08)) & 0x04) {
  61                out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0xC1);
  62        } else {
  63                /* running from Backup flash */
  64                out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0x32);
  65        }
  66#endif
  67        return 0;
  68}
  69
  70int is_micron(void){
  71
  72        ushort brd_rev = *(vu_short *)(CONFIG_SYS_CPLD_BASE + 0x00);
  73        uchar macaddr[6];
  74        u32 brddate, macchk, ismicron;
  75
  76        /*
  77         * MAC address has serial number with date of manufacture
  78         * Boards made before Nov-08 #1180 use Micron memory;
  79         * 001e59 is the STx vendor #
  80         * Default is Elpida since it works for both but is slightly slower
  81         */
  82        ismicron = 0;
  83        if (brd_rev >= 0x0400 && eth_getenv_enetaddr("ethaddr", macaddr)) {
  84                brddate = (macaddr[3] << 16) + (macaddr[4] << 8) + macaddr[5];
  85                macchk = (macaddr[0] << 16) + (macaddr[1] << 8) + macaddr[2];
  86                debug("brddate = %d\n\t", brddate);
  87
  88                if (macchk == 0x001e59 && brddate <= 8111180)
  89                        ismicron = 1;
  90        } else if (brd_rev < 0x400) {
  91                ismicron = 1;
  92        }
  93        debug("Using %s Memory settings\n\t",
  94                ismicron ? "Micron" : "Elpida");
  95        return(ismicron);
  96}
  97
  98phys_size_t initdram(int board_type)
  99{
 100        u32 msize = 0;
 101        /*
 102         * Elpida MDDRC and initialization settings are an alternative
 103         * to the Default Micron ones for all but the earliest Rev 4 boards
 104         */
 105        ddr512x_config_t elpida_mddrc_config = {
 106                .ddr_sys_config   = CONFIG_SYS_MDDRC_SYS_CFG_ELPIDA,
 107                .ddr_time_config0 = CONFIG_SYS_MDDRC_TIME_CFG0,
 108                .ddr_time_config1 = CONFIG_SYS_MDDRC_TIME_CFG1_ELPIDA,
 109                .ddr_time_config2 = CONFIG_SYS_MDDRC_TIME_CFG2_ELPIDA,
 110        };
 111
 112        u32 elpida_init_sequence[] = {
 113                CONFIG_SYS_DDRCMD_NOP,
 114                CONFIG_SYS_DDRCMD_NOP,
 115                CONFIG_SYS_DDRCMD_NOP,
 116                CONFIG_SYS_DDRCMD_NOP,
 117                CONFIG_SYS_DDRCMD_NOP,
 118                CONFIG_SYS_DDRCMD_NOP,
 119                CONFIG_SYS_DDRCMD_NOP,
 120                CONFIG_SYS_DDRCMD_NOP,
 121                CONFIG_SYS_DDRCMD_NOP,
 122                CONFIG_SYS_DDRCMD_NOP,
 123                CONFIG_SYS_DDRCMD_PCHG_ALL,
 124                CONFIG_SYS_DDRCMD_NOP,
 125                CONFIG_SYS_DDRCMD_RFSH,
 126                CONFIG_SYS_DDRCMD_NOP,
 127                CONFIG_SYS_DDRCMD_RFSH,
 128                CONFIG_SYS_DDRCMD_NOP,
 129                CONFIG_SYS_DDRCMD_EM2,
 130                CONFIG_SYS_DDRCMD_EM3,
 131                CONFIG_SYS_DDRCMD_EN_DLL,
 132                CONFIG_SYS_ELPIDA_RES_DLL,
 133                CONFIG_SYS_DDRCMD_PCHG_ALL,
 134                CONFIG_SYS_DDRCMD_RFSH,
 135                CONFIG_SYS_DDRCMD_RFSH,
 136                CONFIG_SYS_DDRCMD_RFSH,
 137                CONFIG_SYS_ELPIDA_INIT_DEV_OP,
 138                CONFIG_SYS_DDRCMD_NOP,
 139                CONFIG_SYS_DDRCMD_NOP,
 140                CONFIG_SYS_DDRCMD_NOP,
 141                CONFIG_SYS_DDRCMD_NOP,
 142                CONFIG_SYS_DDRCMD_NOP,
 143                CONFIG_SYS_DDRCMD_NOP,
 144                CONFIG_SYS_DDRCMD_NOP,
 145                CONFIG_SYS_DDRCMD_NOP,
 146                CONFIG_SYS_DDRCMD_NOP,
 147                CONFIG_SYS_DDRCMD_NOP,
 148                CONFIG_SYS_DDRCMD_OCD_DEFAULT,
 149                CONFIG_SYS_ELPIDA_OCD_EXIT,
 150                CONFIG_SYS_DDRCMD_NOP,
 151                CONFIG_SYS_DDRCMD_NOP,
 152                CONFIG_SYS_DDRCMD_NOP,
 153                CONFIG_SYS_DDRCMD_NOP,
 154                CONFIG_SYS_DDRCMD_NOP,
 155                CONFIG_SYS_DDRCMD_NOP,
 156                CONFIG_SYS_DDRCMD_NOP,
 157                CONFIG_SYS_DDRCMD_NOP,
 158                CONFIG_SYS_DDRCMD_NOP,
 159                CONFIG_SYS_DDRCMD_NOP
 160        };
 161
 162        if (is_micron()) {
 163                msize = fixed_sdram(NULL, NULL, 0);
 164        } else {
 165                msize = fixed_sdram(&elpida_mddrc_config,
 166                                elpida_init_sequence,
 167                                sizeof(elpida_init_sequence)/sizeof(u32));
 168        }
 169
 170        return msize;
 171}
 172
 173int misc_init_r(void)
 174{
 175        u8 tmp_val;
 176
 177        /* Using this for DIU init before the driver in linux takes over
 178         *  Enable the TFP410 Encoder (I2C address 0x38)
 179         */
 180
 181        i2c_set_bus_num(2);
 182        tmp_val = 0xBF;
 183        i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
 184        /* Verify if enabled */
 185        tmp_val = 0;
 186        i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
 187        debug("DVI Encoder Read: 0x%02x\n", tmp_val);
 188
 189        tmp_val = 0x10;
 190        i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
 191        /* Verify if enabled */
 192        tmp_val = 0;
 193        i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
 194        debug("DVI Encoder Read: 0x%02x\n", tmp_val);
 195
 196        return 0;
 197}
 198
 199static  iopin_t ioregs_init[] = {
 200        /* FUNC1=FEC_RX_DV Sets Next 3 to FEC pads */
 201        {
 202                offsetof(struct ioctrl512x, io_control_spdif_txclk), 3, 0,
 203                IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 204                IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 205        },
 206        /* Set highest Slew on 9 PATA pins */
 207        {
 208                offsetof(struct ioctrl512x, io_control_pata_ce1), 9, 1,
 209                IO_PIN_FMUX(0) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 210                IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 211        },
 212        /* FUNC1=FEC_COL Sets Next 15 to FEC pads */
 213        {
 214                offsetof(struct ioctrl512x, io_control_psc0_0), 15, 0,
 215                IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 216                IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 217        },
 218        /* FUNC1=SPDIF_TXCLK */
 219        {
 220                offsetof(struct ioctrl512x, io_control_lpc_cs1), 1, 0,
 221                IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 222                IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 223        },
 224        /* FUNC2=SPDIF_TX and sets Next pin to SPDIF_RX */
 225        {
 226                offsetof(struct ioctrl512x, io_control_i2c1_scl), 2, 0,
 227                IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 228                IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 229        },
 230        /* FUNC2=DIU CLK */
 231        {
 232                offsetof(struct ioctrl512x, io_control_psc6_0), 1, 0,
 233                IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 234                IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 235        },
 236        /* FUNC2=DIU_HSYNC */
 237        {
 238                offsetof(struct ioctrl512x, io_control_psc6_1), 1, 0,
 239                IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 240                IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 241        },
 242        /* FUNC2=DIUVSYNC Sets Next 26 to DIU Pads */
 243        {
 244                offsetof(struct ioctrl512x, io_control_psc6_4), 26, 0,
 245                IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 246                IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 247        }
 248};
 249
 250static  iopin_t rev2_silicon_pci_ioregs_init[] = {
 251        /* FUNC0=PCI Sets next 54 to PCI pads */
 252        {
 253                offsetof(struct ioctrl512x, io_control_pci_ad31), 54, 0,
 254                IO_PIN_FMUX(0) | IO_PIN_HOLD(0) | IO_PIN_DS(0)
 255        }
 256};
 257
 258int checkboard (void)
 259{
 260        ushort brd_rev = *(vu_short *) (CONFIG_SYS_CPLD_BASE + 0x00);
 261        uchar cpld_rev = *(vu_char *) (CONFIG_SYS_CPLD_BASE + 0x02);
 262        volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
 263        u32 spridr = in_be32(&im->sysconf.spridr);
 264
 265        printf ("Board: MPC5121ADS rev. 0x%04x (CPLD rev. 0x%02x)\n",
 266                brd_rev, cpld_rev);
 267
 268        /* initialize function mux & slew rate IO inter alia on IO Pins  */
 269        iopin_initialize(ioregs_init, ARRAY_SIZE(ioregs_init));
 270
 271        if (SVR_MJREV (spridr) >= 2)
 272                iopin_initialize(rev2_silicon_pci_ioregs_init, 1);
 273
 274        return 0;
 275}
 276
 277#ifdef CONFIG_OF_BOARD_SETUP
 278int ft_board_setup(void *blob, bd_t *bd)
 279{
 280        ft_cpu_setup(blob, bd);
 281
 282        return 0;
 283}
 284#endif /* CONFIG_OF_BOARD_SETUP */
 285