/*
 * Copyright (C) 2006 Freescale Semiconductor, Inc.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 */
#define CONFIG_E300             1       /* E300 family */
#define CONFIG_QE               1       /* Has QE */
#define CONFIG_MPC832x          1       /* MPC832x CPU specific */
#define CONFIG_MPC832XEMDS      1       /* MPC832XEMDS board specific */

#define CONFIG_SYS_TEXT_BASE    0xFE000000

/*
 * System Clock Setup
 */
#ifdef CONFIG_PCISLAVE
#define CONFIG_83XX_PCICLK      66000000        /* in HZ */
#else
#define CONFIG_83XX_CLKIN       66000000        /* in Hz */
#endif

#ifndef CONFIG_SYS_CLK_FREQ
#define CONFIG_SYS_CLK_FREQ     66000000
#endif

/*
 * Hardware Reset Configuration Word
 */
#define CONFIG_SYS_HRCW_LOW (\
        HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
        HRCWL_DDR_TO_SCB_CLK_2X1 |\
        HRCWL_VCO_1X2 |\
        HRCWL_CSB_TO_CLKIN_2X1 |\
        HRCWL_CORE_TO_CSB_2X1 |\
        HRCWL_CE_PLL_VCO_DIV_2 |\
        HRCWL_CE_PLL_DIV_1X1 |\
        HRCWL_CE_TO_PLL_1X3)

#ifdef CONFIG_PCISLAVE
#define CONFIG_SYS_HRCW_HIGH (\
        HRCWH_PCI_AGENT |\
        HRCWH_PCI1_ARBITER_DISABLE |\
        HRCWH_CORE_ENABLE |\
        HRCWH_FROM_0XFFF00100 |\
        HRCWH_BOOTSEQ_DISABLE |\
        HRCWH_SW_WATCHDOG_DISABLE |\
        HRCWH_ROM_LOC_LOCAL_16BIT |\
        HRCWH_BIG_ENDIAN |\
        HRCWH_LALE_NORMAL)
#else
#define CONFIG_SYS_HRCW_HIGH (\
        HRCWH_PCI_HOST |\
        HRCWH_PCI1_ARBITER_ENABLE |\
        HRCWH_CORE_ENABLE |\
        HRCWH_FROM_0X00000100 |\
        HRCWH_BOOTSEQ_DISABLE |\
        HRCWH_SW_WATCHDOG_DISABLE |\
        HRCWH_ROM_LOC_LOCAL_16BIT |\
        HRCWH_BIG_ENDIAN |\
        HRCWH_LALE_NORMAL)
#endif

/*
 * System IO Config
 */
#define CONFIG_SYS_SICRL                0x00000000

#define CONFIG_BOARD_EARLY_INIT_F       /* call board_pre_init */
#define CONFIG_BOARD_EARLY_INIT_R

/*
 * IMMR new address
 */
#define CONFIG_SYS_IMMR         0xE0000000

/*
 * DDR Setup
 */
#define CONFIG_SYS_DDR_BASE     0x00000000      /* DDR is system memory */
#define CONFIG_SYS_SDRAM_BASE   CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDRCDR       0x73000002      /* DDR II voltage is 1.8V */

#undef CONFIG_SPD_EEPROM
#if defined(CONFIG_SPD_EEPROM)
/* Determine DDR configuration from I2C interface
 */
#define SPD_EEPROM_ADDRESS      0x51    /* DDR SODIMM */
#else
/* Manually set up DDR parameters
 */
#define CONFIG_SYS_DDR_SIZE             128     /* MB */
#define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN \
                                        | CSCONFIG_AP \
                                        | CSCONFIG_ODT_WR_CFG \
                                        | CSCONFIG_ROW_BIT_13 \
                                        | CSCONFIG_COL_BIT_10)
                                        /* 0x80840102 */
#define CONFIG_SYS_DDR_TIMING_0         ((0 << TIMING_CFG0_RWT_SHIFT) \
                                        | (0 << TIMING_CFG0_WRT_SHIFT) \
                                        | (0 << TIMING_CFG0_RRT_SHIFT) \
                                        | (0 << TIMING_CFG0_WWT_SHIFT) \
                                        | (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \
                                        | (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \
                                        | (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \
                                        | (2 << TIMING_CFG0_MRS_CYC_SHIFT))
                                        /* 0x00220802 */
#define CONFIG_SYS_DDR_TIMING_1         ((3 << TIMING_CFG1_PRETOACT_SHIFT) \
                                        | (9 << TIMING_CFG1_ACTTOPRE_SHIFT) \
                                        | (3 << TIMING_CFG1_ACTTORW_SHIFT) \
                                        | (5 << TIMING_CFG1_CASLAT_SHIFT) \
                                        | (13 << TIMING_CFG1_REFREC_SHIFT) \
                                        | (3 << TIMING_CFG1_WRREC_SHIFT) \
                                        | (2 << TIMING_CFG1_ACTTOACT_SHIFT) \
                                        | (2 << TIMING_CFG1_WRTORD_SHIFT))
                                        /* 0x3935D322 */
#define CONFIG_SYS_DDR_TIMING_2         ((0 << TIMING_CFG2_ADD_LAT_SHIFT) \
                                | (31 << TIMING_CFG2_CPO_SHIFT) \
                                | (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \
                                | (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) \
                                | (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \
                                | (3 << TIMING_CFG2_CKE_PLS_SHIFT) \
                                | (10 << TIMING_CFG2_FOUR_ACT_SHIFT))
                                /* 0x0F9048CA */
#define CONFIG_SYS_DDR_TIMING_3         0x00000000
#define CONFIG_SYS_DDR_CLK_CNTL         DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
                                        /* 0x02000000 */
#define CONFIG_SYS_DDR_MODE             ((0x4440 << SDRAM_MODE_ESD_SHIFT) \
                                        | (0x0232 << SDRAM_MODE_SD_SHIFT))
                                        /* 0x44400232 */
#define CONFIG_SYS_DDR_MODE2            0x8000c000
#define CONFIG_SYS_DDR_INTERVAL         ((800 << SDRAM_INTERVAL_REFINT_SHIFT) \
                                        | (100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
                                        /* 0x03200064 */
#define CONFIG_SYS_DDR_CS0_BNDS         0x00000007
#define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SREN \
                                        | SDRAM_CFG_SDRAM_TYPE_DDR2 \
                                        | SDRAM_CFG_32_BE)
                                        /* 0x43080000 */
#define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000
#endif

/*
 * Memory test
 */
#undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
#define CONFIG_SYS_MEMTEST_START        0x00000000      /* memtest region */
#define CONFIG_SYS_MEMTEST_END          0x00100000

/*
 * The reserved memory
 */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#else
#undef  CONFIG_SYS_RAMBOOT
#endif

/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN  (512 * 1024)    /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN   (256 * 1024)    /* Reserved for malloc */

/*
 * Initial RAM Base Address Setup
 */
#define CONFIG_SYS_INIT_RAM_LOCK        1
#define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000      /* Initial RAM addr */
#define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET      \
                        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)

/*
 * Local Bus Configuration & Clock Setup
 */
#define CONFIG_SYS_LCRR_DBYP            LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV          LCRR_CLKDIV_2
#define CONFIG_SYS_LBC_LBCR             0x00000000

/*
 * FLASH on the Local Bus
 */
#define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
#define CONFIG_FLASH_CFI_DRIVER         /* use the CFI driver */
#define CONFIG_SYS_FLASH_BASE   0xFE000000      /* FLASH base address */
#define CONFIG_SYS_FLASH_SIZE   16      /* FLASH size is 16M */
#define CONFIG_SYS_FLASH_PROTECTION     1       /* Use h/w Flash protection. */

                                        /* Window base at flash base */
#define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_32MB)

#define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
                                | BR_PS_16      /* 16 bit port */ \
                                | BR_MS_GPCM    /* MSEL = GPCM */ \
                                | BR_V)         /* valid */
#define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
                                | OR_GPCM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET \
                                | OR_GPCM_EAD)
                                /* 0xfe006ff7 */

#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       128     /* sectors per device */

#undef CONFIG_SYS_FLASH_CHECKSUM

/*
 * BCSR on the Local Bus
 */
#define CONFIG_SYS_BCSR                 0xF8000000
                                        /* Access window base at BCSR base */
#define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_BCSR
#define CONFIG_SYS_LBLAWAR1_PRELIM      (LBLAWAR_EN | LBLAWAR_32KB)

#define CONFIG_SYS_BR1_PRELIM           (CONFIG_SYS_BCSR \
                                        | BR_PS_8 \
                                        | BR_MS_GPCM \
                                        | BR_V)
#define CONFIG_SYS_OR1_PRELIM           (OR_AM_32KB \
                                        | OR_GPCM_XAM \
                                        | OR_GPCM_CSNT \
                                        | OR_GPCM_XACS \
                                        | OR_GPCM_SCY_15 \
                                        | OR_GPCM_TRLX_SET \
                                        | OR_GPCM_EHTR_SET \
                                        | OR_GPCM_EAD)
                                        /* 0xFFFFE9F7 */

/*
 * Windows to access PIB via local bus
 */
                                        /* PIB window base 0xF8008000 */
#define CONFIG_SYS_PIB_BASE             0xF8008000
#define CONFIG_SYS_PIB_WINDOW_SIZE      (32 * 1024)
#define CONFIG_SYS_LBLAWBAR3_PRELIM     CONFIG_SYS_PIB_BASE
#define CONFIG_SYS_LBLAWAR3_PRELIM      (LBLAWAR_EN | LBLAWAR_64KB)

/*
 * CS2 on Local Bus, to PIB
 */
#define CONFIG_SYS_BR2_PRELIM   (CONFIG_SYS_PIB_BASE \
                                | BR_PS_8 \
                                | BR_MS_GPCM \
                                | BR_V)
                                /* 0xF8008801 */
#define CONFIG_SYS_OR2_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
                                | OR_GPCM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET \
                                | OR_GPCM_EAD)
                                /* 0xffffe9f7 */

/*
 * CS3 on Local Bus, to PIB
 */
#define CONFIG_SYS_BR3_PRELIM   ((CONFIG_SYS_PIB_BASE + \
                                        CONFIG_SYS_PIB_WINDOW_SIZE) \
                                | BR_PS_8 \
                                | BR_MS_GPCM \
                                | BR_V)
                                /* 0xF8010801 */
#define CONFIG_SYS_OR3_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_PIB_WINDOW_SIZE) \
                                | OR_GPCM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET \
                                | OR_GPCM_EAD)
                                /* 0xffffe9f7 */

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
                {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

#define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
#define CONFIG_AUTO_COMPLETE            /* add autocompletion support   */

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        400000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_I2C_NOPROBES         { {0, 0x51} }

/*
 * Config on-board RTC
 */
#define CONFIG_RTC_DS1374               /* use ds1374 rtc via i2c */
#define CONFIG_SYS_I2C_RTC_ADDR 0x68    /* at address 0x68 */

/*
 * General PCI
 * Addresses are mapped 1-1.
 */
#define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
#define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
#define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCI1_IO_BASE         0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS         0xE0300000
#define CONFIG_SYS_PCI1_IO_SIZE         0x100000        /* 1M */

#define CONFIG_SYS_PCI_SLV_MEM_LOCAL    CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_PCI_SLV_MEM_BUS      0x00000000
#define CONFIG_SYS_PCI_SLV_MEM_SIZE     0x80000000

#ifdef CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE

#define CONFIG_83XX_PCI_STREAMING

#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID  0x1957  /* Freescale */

#endif  /* CONFIG_PCI */

/*
 * QE UEC ethernet configuration
 */
#define CONFIG_UEC_ETH
#define CONFIG_ETHPRIME         "UEC0"

#define CONFIG_UEC_ETH1         /* ETH3 */

#ifdef CONFIG_UEC_ETH1
#define CONFIG_SYS_UEC1_UCC_NUM 2       /* UCC3 */
#define CONFIG_SYS_UEC1_RX_CLK          QE_CLK9
#define CONFIG_SYS_UEC1_TX_CLK          QE_CLK10
#define CONFIG_SYS_UEC1_ETH_TYPE        FAST_ETH
#define CONFIG_SYS_UEC1_PHY_ADDR        3
#define CONFIG_SYS_UEC1_INTERFACE_TYPE  PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
#endif

#define CONFIG_UEC_ETH2         /* ETH4 */

#ifdef CONFIG_UEC_ETH2
#define CONFIG_SYS_UEC2_UCC_NUM 3       /* UCC4 */
#define CONFIG_SYS_UEC2_RX_CLK          QE_CLK7
#define CONFIG_SYS_UEC2_TX_CLK          QE_CLK8
#define CONFIG_SYS_UEC2_ETH_TYPE        FAST_ETH
#define CONFIG_SYS_UEC2_PHY_ADDR        4
#define CONFIG_SYS_UEC2_INTERFACE_TYPE  PHY_INTERFACE_MODE_MII
#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
#endif

/*
 * Environment
 */
#ifndef CONFIG_SYS_RAMBOOT
        #define CONFIG_ENV_IS_IN_FLASH  1
        #define CONFIG_ENV_ADDR         \
                        (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
        #define CONFIG_ENV_SECT_SIZE    0x20000
        #define CONFIG_ENV_SIZE         0x2000
#else
        #define CONFIG_SYS_NO_FLASH     1       /* Flash is not usable now */
        #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
        #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
        #define CONFIG_ENV_SIZE         0x2000
#endif

#define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME

/*
 * Command line configuration.
 */

#if defined(CONFIG_PCI)
    #define CONFIG_CMD_PCI
#endif

#undef CONFIG_WATCHDOG          /* watchdog disabled */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP     /* undef to save memory */
#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */

#if defined(CONFIG_CMD_KGDB)
        #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buffer Size */
#else
        #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
#endif

                                /* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS      16      /* max number of command args */
                                /* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
                                        /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTMAPSZ            (256 << 20)
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

/*
 * Core HID Setup
 */
#define CONFIG_SYS_HID0_INIT    0x000000000
#define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
                                 HID0_ENABLE_INSTRUCTION_CACHE)
#define CONFIG_SYS_HID2         HID2_HBE

/*
 * MMU Setup
 */

#define CONFIG_HIGH_BATS        1       /* High BATs supported */

/* DDR: cache cacheable */
#define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U

/* IMMRBAR & PCI IO: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR \
                                | BATU_BL_4M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U

/* BCSR: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_BCSR \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U       (CONFIG_SYS_BCSR \
                                | BATU_BL_128K \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U

/* FLASH: icache cacheable, but dcache-inhibit and guarded */
#define CONFIG_SYS_IBAT3L       (CONFIG_SYS_FLASH_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT3U       (CONFIG_SYS_FLASH_BASE \
                                | BATU_BL_32M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT3L       (CONFIG_SYS_FLASH_BASE \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U

#define CONFIG_SYS_IBAT4L       (0)
#define CONFIG_SYS_IBAT4U       (0)
#define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U

/* Stack in dcache: cacheable, no memory coherence */
#define CONFIG_SYS_IBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW)
#define CONFIG_SYS_IBAT5U       (CONFIG_SYS_INIT_RAM_ADDR \
                                | BATU_BL_128K \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U

#ifdef CONFIG_PCI
/* PCI MEM space: cacheable */
#define CONFIG_SYS_IBAT6L       (CONFIG_SYS_PCI1_MEM_PHYS \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT6U       (CONFIG_SYS_PCI1_MEM_PHYS \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
/* PCI MMIO space: cache-inhibit and guarded */
#define CONFIG_SYS_IBAT7L       (CONFIG_SYS_PCI1_MMIO_PHYS \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT7U       (CONFIG_SYS_PCI1_MMIO_PHYS \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
#else
#define CONFIG_SYS_IBAT6L       (0)
#define CONFIG_SYS_IBAT6U       (0)
#define CONFIG_SYS_IBAT7L       (0)
#define CONFIG_SYS_IBAT7U       (0)
#define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
#endif

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
#endif

/*
 * Environment Configuration
 */ #define CONFIG_ENV_OVERWRITE

#if defined(CONFIG_UEC_ETH)
#define CONFIG_HAS_ETH0
#define CONFIG_HAS_ETH1
#endif

#define CONFIG_BAUDRATE 115200

#define CONFIG_LOADADDR 800000  /* default location for tftp and bootm */

#undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */

#define CONFIG_EXTRA_ENV_SETTINGS                                       \
        "netdev=eth0\0"                                                 \
        "consoledev=ttyS0\0"                                            \
        "ramdiskaddr=1000000\0"                                         \
        "ramdiskfile=ramfs.83xx\0"                                      \
        "fdtaddr=780000\0"                                              \
        "fdtfile=mpc832x_mds.dtb\0"                                     \
        ""

#define CONFIG_NFSBOOTCOMMAND                                           \
        "setenv bootargs root=/dev/nfs rw "                             \
                "nfsroot=$serverip:$rootpath "                          \
                "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
                                                        "$netdev:off "  \
                "console=$consoledev,$baudrate $othbootargs;"           \
        "tftp $loadaddr $bootfile;"                                     \
        "tftp $fdtaddr $fdtfile;"                                       \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND                                           \
        "setenv bootargs root=/dev/ram rw "                             \
                "console=$consoledev,$baudrate $othbootargs;"           \
        "tftp $ramdiskaddr $ramdiskfile;"                               \
        "tftp $loadaddr $bootfile;"                                     \
        "tftp $fdtaddr $fdtfile;"                                       \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND

#endif  /* __CONFIG_H */