1/* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14#ifndef __AT91RM9200EK_CONFIG_H__ 15#define __AT91RM9200EK_CONFIG_H__ 16 17#include <linux/sizes.h> 18 19/* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26#ifdef CONFIG_RAMBOOT 27#define CONFIG_SKIP_LOWLEVEL_INIT 28#define CONFIG_SYS_TEXT_BASE 0x20100000 29#else 30#define CONFIG_SYS_TEXT_BASE 0x10000000 31#endif 32 33/* 34 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 35 * AT91C_MAIN_CLOCK is the frequency of PLLA output 36 * AT91C_MASTER_CLOCK is the peripherial clock 37 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 38 * set in arch/arm/cpu/arm920t/at91/timer.c) 39 * CONFIG_SYS_HZ is the tick rate for timer tc0 40 */ 41#define AT91C_XTAL_CLOCK 18432000 42#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 43#define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 44#define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 45#define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 46 47/* CPU configuration */ 48#define CONFIG_AT91RM9200 49#define CONFIG_AT91RM9200EK 50#define CONFIG_CPUAT91 51#define USE_920T_MMU 52 53#include <asm/hardware.h> /* needed for port definitions */ 54 55#define CONFIG_CMDLINE_TAG 56#define CONFIG_SETUP_MEMORY_TAGS 57#define CONFIG_INITRD_TAG 58 59/* 60 * Memory Configuration 61 */ 62#define CONFIG_NR_DRAM_BANKS 1 63#define CONFIG_SYS_SDRAM_BASE 0x20000000 64#define CONFIG_SYS_SDRAM_SIZE SZ_32M 65 66#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 67#define CONFIG_SYS_MEMTEST_END \ 68 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 69 70/* 71 * LowLevel Init 72 */ 73#ifndef CONFIG_SKIP_LOWLEVEL_INIT 74#define CONFIG_SYS_USE_MAIN_OSCILLATOR 75/* flash */ 76#define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 77#define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 78 79/* clocks */ 80#define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 81#define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 82/* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 83#define CONFIG_SYS_MCKR_VAL 0x00000202 84 85/* sdram */ 86#define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 87#define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 88#define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 89#define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 90#define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 91#define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 92#define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 93#define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 94#define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 95#define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 96#define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 97#define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 98#define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 99#endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 100 101/* 102 * Hardware drivers 103 */ 104/* 105 * Choose a USART for serial console 106 * CONFIG_DBGU is DBGU unit on J10 107 * CONFIG_USART1 is USART1 on J14 108 */ 109#define CONFIG_ATMEL_USART 110#define CONFIG_USART_BASE ATMEL_BASE_DBGU 111#define CONFIG_USART_ID 0/* ignored in arm */ 112 113/* 114 * Command line configuration. 115 */ 116 117/* 118 * Network Driver Setting 119 */ 120#define CONFIG_DRIVER_AT91EMAC 121#define CONFIG_SYS_RX_ETH_BUFFER 16 122#define CONFIG_RMII 123#define CONFIG_MII 124 125/* 126 * NOR Flash 127 */ 128#define CONFIG_FLASH_CFI_DRIVER 129#define CONFIG_SYS_FLASH_CFI 130#define CONFIG_SYS_FLASH_BASE 0x10000000 131#define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 132#define PHYS_FLASH_SIZE SZ_8M 133#define CONFIG_SYS_MAX_FLASH_BANKS 1 134#define CONFIG_SYS_MAX_FLASH_SECT 256 135#define CONFIG_SYS_FLASH_PROTECTION 136 137/* 138 * USB Config 139 */ 140#define CONFIG_USB_ATMEL 1 141#define CONFIG_USB_ATMEL_CLK_SEL_PLLB 142#define CONFIG_USB_OHCI_NEW 1 143 144#define CONFIG_SYS_USB_OHCI_CPU_INIT 1 145#define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 146#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 147#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 148 149/* 150 * Environment Settings 151 */ 152 153/* 154 * after u-boot.bin 155 */ 156#define CONFIG_ENV_ADDR \ 157 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 158#define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 159/* The following #defines are needed to get flash environment right */ 160#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 161#define CONFIG_SYS_MONITOR_LEN SZ_256K 162 163/* 164 * Boot option 165 */ 166 167/* default load address */ 168#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 169#define CONFIG_ENV_OVERWRITE 170 171/* 172 * Shell Settings 173 */ 174#define CONFIG_CMDLINE_EDITING 175#define CONFIG_SYS_LONGHELP 176#define CONFIG_AUTO_COMPLETE 177 178/* 179 * Size of malloc() pool 180 */ 181#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 182 SZ_4K) 183 184#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 185 - GENERATED_GBL_DATA_SIZE) 186 187#endif /* __AT91RM9200EK_CONFIG_H__ */ 188