LXR uboot/drivers/usb/Kconfig

   1menuconfig USB
   2        bool "USB support"
   3        ---help---
   4          Universal Serial Bus (USB) is a specification for a serial bus
   5          subsystem which offers higher speeds and more features than the
   6          traditional PC serial port.  The bus supplies power to peripherals
   7          and allows for hot swapping.  Up to 127 USB peripherals can be
   8          connected to a single USB host in a tree structure.
   9
  10          The USB host is the root of the tree, the peripherals are the
  11          leaves and the inner nodes are special USB devices called hubs.
  12          Most PCs now have USB host ports, used to connect peripherals
  13          such as scanners, keyboards, mice, modems, cameras, disks,
  14          flash memory, network links, and printers to the PC.
  15
  16          Say Y here if your device has an USB port, either host, peripheral or
  17          dual-role.
  18
  19          For an USB host port, you then need to say Y to at least one of the
  20          Host Controller Driver (HCD) options below.  Choose a USB 1.1
  21          controller, such as "UHCI HCD support" or "OHCI HCD support",
  22          and "EHCI HCD (USB 2.0) support" except for older systems that
  23          do not have USB 2.0 support.  It doesn't normally hurt to select
  24          them all if you are not certain.
  25
  26          If your system has a device-side USB port, used in the peripheral
  27          side of the USB protocol, see the "USB Gadget" framework instead.
  28
  29          After choosing your HCD, then select drivers for the USB peripherals
  30          you'll be using.  You may want to check out the information provided
  31          in <file:Documentation/usb/> and especially the links given in
  32          <file:Documentation/usb/usb-help.txt>.
  33
  34if USB
  35
  36config DM_USB
  37        bool "Enable driver model for USB"
  38        depends on USB && DM
  39        help
  40          Enable driver model for USB. The USB interface is then implemented
  41          by the USB uclass. Multiple USB controllers of different types
  42          (XHCI, EHCI) can be attached and used. The 'usb' command works as
  43          normal. OCHI is not supported at present.
  44
  45          Much of the code is shared but with this option enabled the USB
  46          uclass takes care of device enumeration. USB devices can be
  47          declared with the U_BOOT_USB_DEVICE() macro and will be
  48          automatically probed when found on the bus.
  49
  50config SPL_DM_USB
  51        bool "Enable driver model for USB in SPL"
  52        depends on SPL_DM && DM_USB
  53        default y
  54
  55config DM_USB_GADGET
  56        bool "Enable driver model for USB Gadget"
  57        depends on DM_USB
  58        help
  59          Enable driver model for USB Gadget (Peripheral
  60          mode)
  61
  62config SPL_DM_USB_GADGET
  63        bool "Enable driver model for USB Gadget in sPL"
  64        depends on SPL_DM_USB
  65        help
  66          Enable driver model for USB Gadget in SPL
  67          (Peripheral mode)
  68
  69source "drivers/usb/host/Kconfig"
  70
  71source "drivers/usb/dwc3/Kconfig"
  72
  73source "drivers/usb/musb/Kconfig"
  74
  75source "drivers/usb/musb-new/Kconfig"
  76
  77source "drivers/usb/emul/Kconfig"
  78
  79source "drivers/usb/phy/Kconfig"
  80
  81source "drivers/usb/ulpi/Kconfig"
  82
  83comment "USB peripherals"
  84
  85config USB_STORAGE
  86        bool "USB Mass Storage support"
  87        depends on !(BLK && !DM_USB)
  88        ---help---
  89          Say Y here if you want to connect USB mass storage devices to your
  90          board's USB port.
  91
  92config USB_KEYBOARD
  93        bool "USB Keyboard support"
  94        select SYS_STDIO_DEREGISTER
  95        ---help---
  96          Say Y here if you want to use a USB keyboard for U-Boot command line
  97          input.
  98
  99if USB_KEYBOARD
 100
 101choice
 102        prompt "USB keyboard polling"
 103        default SYS_USB_EVENT_POLL
 104        ---help---
 105          Enable a polling mechanism for USB keyboard.
 106
 107        config SYS_USB_EVENT_POLL
 108                bool "Interrupt polling"
 109
 110        config SYS_USB_EVENT_POLL_VIA_INT_QUEUE
 111                bool "Poll via interrupt queue"
 112
 113        config SYS_USB_EVENT_POLL_VIA_CONTROL_EP
 114                bool "Poll via control EP"
 115
 116endchoice
 117
 118endif
 119
 120source "drivers/usb/gadget/Kconfig"
 121
 122source "drivers/usb/eth/Kconfig"
 123
 124endif
 125