// SPDX-License-Identifier: GPL-2.0+
/*
 * Freescale i.MX23/i.MX28 LCDIF driver
 *
 * Copyright (C) 2011-2013 Marek Vasut <marex@denx.de>
 */
#include <common.h>
#include <malloc.h>
#include <video_fb.h>

#include <asm/arch/imx-regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <linux/errno.h>
#include <asm/io.h>

#include <asm/mach-imx/dma.h>

#include "videomodes.h"

#define PS2KHZ(ps)      (1000000000UL / (ps))

static GraphicDevice panel;
struct mxs_dma_desc desc;

/**
 * mxsfb_system_setup() - Fine-tune LCDIF configuration
 *
 * This function is used to adjust the LCDIF configuration. This is usually
 * needed when driving the controller in System-Mode to operate an 8080 or
 * 6800 connected SmartLCD.
 */
__weak void mxsfb_system_setup(void)
{
}

/*
 * ARIES M28EVK:
 * setenv videomode
 * video=ctfb:x:800,y:480,depth:18,mode:0,pclk:30066,
 *       le:0,ri:256,up:0,lo:45,hs:1,vs:1,sync:100663296,vmode:0
 *
 * Freescale mx23evk/mx28evk with a Seiko 4.3'' WVGA panel:
 * setenv videomode
 * video=ctfb:x:800,y:480,depth:24,mode:0,pclk:29851,
 *       le:89,ri:164,up:23,lo:10,hs:10,vs:10,sync:0,vmode:0
 */

static void mxs_lcd_init(GraphicDevice *panel,
                        struct ctfb_res_modes *mode, int bpp)
{
        struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
        uint32_t word_len = 0, bus_width = 0;
        uint8_t valid_data = 0;

        /* Kick in the LCDIF clock */
        mxs_set_lcdclk(MXS_LCDIF_BASE, PS2KHZ(mode->pixclock));

        /* Restart the LCDIF block */
        mxs_reset_block(&regs->hw_lcdif_ctrl_reg);

        switch (bpp) {
        case 24:
                word_len = LCDIF_CTRL_WORD_LENGTH_24BIT;
                bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_24BIT;
                valid_data = 0x7;
                break;
        case 18:
                word_len = LCDIF_CTRL_WORD_LENGTH_24BIT;
                bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_18BIT;
                valid_data = 0x7;
                break;
        case 16:
                word_len = LCDIF_CTRL_WORD_LENGTH_16BIT;
                bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_16BIT;
                valid_data = 0xf;
                break;
        case 8:
                word_len = LCDIF_CTRL_WORD_LENGTH_8BIT;
                bus_width = LCDIF_CTRL_LCD_DATABUS_WIDTH_8BIT;
                valid_data = 0xf;
                break;
        }

        writel(bus_width | word_len | LCDIF_CTRL_DOTCLK_MODE |
                LCDIF_CTRL_BYPASS_COUNT | LCDIF_CTRL_LCDIF_MASTER,
                &regs->hw_lcdif_ctrl);

        writel(valid_data << LCDIF_CTRL1_BYTE_PACKING_FORMAT_OFFSET,
                &regs->hw_lcdif_ctrl1);

        mxsfb_system_setup();

        writel((mode->yres << LCDIF_TRANSFER_COUNT_V_COUNT_OFFSET) | mode->xres,
                &regs->hw_lcdif_transfer_count);

        writel(LCDIF_VDCTRL0_ENABLE_PRESENT | LCDIF_VDCTRL0_ENABLE_POL |
                LCDIF_VDCTRL0_VSYNC_PERIOD_UNIT |
                LCDIF_VDCTRL0_VSYNC_PULSE_WIDTH_UNIT |
                mode->vsync_len, &regs->hw_lcdif_vdctrl0);
        writel(mode->upper_margin + mode->lower_margin +
                mode->vsync_len + mode->yres,
                &regs->hw_lcdif_vdctrl1);
        writel((mode->hsync_len << LCDIF_VDCTRL2_HSYNC_PULSE_WIDTH_OFFSET) |
                (mode->left_margin + mode->right_margin +
                mode->hsync_len + mode->xres),
                &regs->hw_lcdif_vdctrl2);
        writel(((mode->left_margin + mode->hsync_len) <<
                LCDIF_VDCTRL3_HORIZONTAL_WAIT_CNT_OFFSET) |
                (mode->upper_margin + mode->vsync_len),
                &regs->hw_lcdif_vdctrl3);
        writel((0 << LCDIF_VDCTRL4_DOTCLK_DLY_SEL_OFFSET) | mode->xres,
                &regs->hw_lcdif_vdctrl4);

        writel(panel->frameAdrs, &regs->hw_lcdif_cur_buf);
        writel(panel->frameAdrs, &regs->hw_lcdif_next_buf);

        /* Flush FIFO first */
        writel(LCDIF_CTRL1_FIFO_CLEAR, &regs->hw_lcdif_ctrl1_set);

#ifndef CONFIG_VIDEO_MXS_MODE_SYSTEM
        /* Sync signals ON */
        setbits_le32(&regs->hw_lcdif_vdctrl4, LCDIF_VDCTRL4_SYNC_SIGNALS_ON);
#endif

        /* FIFO cleared */
        writel(LCDIF_CTRL1_FIFO_CLEAR, &regs->hw_lcdif_ctrl1_clr);

        /* RUN! */
        writel(LCDIF_CTRL_RUN, &regs->hw_lcdif_ctrl_set);
}

void lcdif_power_down(void)
{
        struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;
        int timeout = 1000000;

        if (!panel.frameAdrs)
                return;

        writel(panel.frameAdrs, &regs->hw_lcdif_cur_buf_reg);
        writel(panel.frameAdrs, &regs->hw_lcdif_next_buf_reg);
        writel(LCDIF_CTRL1_VSYNC_EDGE_IRQ, &regs->hw_lcdif_ctrl1_clr);
        while (--timeout) {
                if (readl(&regs->hw_lcdif_ctrl1_reg) &
                    LCDIF_CTRL1_VSYNC_EDGE_IRQ)
                        break;
                udelay(1);
        }
        mxs_reset_block((struct mxs_register_32 *)&regs->hw_lcdif_ctrl_reg);
}

void *video_hw_init(void)
{
        int bpp = -1;
        char *penv;
        void *fb;
        struct ctfb_res_modes mode;

        puts("Video: ");

        /* Suck display configuration from "videomode" variable */
        penv = env_get("videomode");
        if (!penv) {
                puts("MXSFB: 'videomode' variable not set!\n");
                return NULL;
        }

        bpp = video_get_params(&mode, penv);

        /* fill in Graphic device struct */
        sprintf(panel.modeIdent, "%dx%dx%d",
                        mode.xres, mode.yres, bpp);

        panel.winSizeX = mode.xres;
        panel.winSizeY = mode.yres;
        panel.plnSizeX = mode.xres;
        panel.plnSizeY = mode.yres;

        switch (bpp) {
        case 24:
        case 18:
                panel.gdfBytesPP = 4;
                panel.gdfIndex = GDF_32BIT_X888RGB;
                break;
        case 16:
                panel.gdfBytesPP = 2;
                panel.gdfIndex = GDF_16BIT_565RGB;
                break;
        case 8:
                panel.gdfBytesPP = 1;
                panel.gdfIndex = GDF__8BIT_INDEX;
                break;
        default:
                printf("MXSFB: Invalid BPP specified! (bpp = %i)\n", bpp);
                return NULL;
        }

        panel.memSize = mode.xres * mode.yres * panel.gdfBytesPP;

        /* Allocate framebuffer */
        fb = memalign(ARCH_DMA_MINALIGN,
                      roundup(panel.memSize, ARCH_DMA_MINALIGN));
        if (!fb) {
                printf("MXSFB: Error allocating framebuffer!\n");
                return NULL;
        }

        /* Wipe framebuffer */
        memset(fb, 0, panel.memSize);

        panel.frameAdrs = (u32)fb;

        printf("%s\n", panel.modeIdent);

        /* Start framebuffer */
        mxs_lcd_init(&panel, &mode, bpp);

#ifdef CONFIG_VIDEO_MXS_MODE_SYSTEM
        /*
         * If the LCD runs in system mode, the LCD refresh has to be triggered
         * manually by setting the RUN bit in HW_LCDIF_CTRL register. To avoid
         * having to set this bit manually after every single change in the
         * framebuffer memory, we set up specially crafted circular DMA, which
         * sets the RUN bit, then waits until it gets cleared and repeats this
         * infinitelly. This way, we get smooth continuous updates of the LCD.
         */
        struct mxs_lcdif_regs *regs = (struct mxs_lcdif_regs *)MXS_LCDIF_BASE;

        memset(&desc, 0, sizeof(struct mxs_dma_desc));
        desc.address = (dma_addr_t)&desc;
        desc.cmd.data = MXS_DMA_DESC_COMMAND_NO_DMAXFER | MXS_DMA_DESC_CHAIN |
                        MXS_DMA_DESC_WAIT4END |
                        (1 << MXS_DMA_DESC_PIO_WORDS_OFFSET);
        desc.cmd.pio_words[0] = readl(&regs->hw_lcdif_ctrl) | LCDIF_CTRL_RUN;
        desc.cmd.next = (uint32_t)&desc.cmd;

        /* Execute the DMA chain. */
        mxs_dma_circ_start(MXS_DMA_CHANNEL_AHB_APBH_LCDIF, &desc);
#endif

        return (void *)&panel;
}