1
2
3
4
5
6#ifndef __LS1012ARDB_H__
7#define __LS1012ARDB_H__
8
9#include "ls1012a_common.h"
10
11
12#define CONFIG_DIMM_SLOTS_PER_CTLR 1
13#define CONFIG_CHIP_SELECTS_PER_CTRL 1
14#define CONFIG_SYS_SDRAM_SIZE 0x40000000
15#define CONFIG_CMD_MEMINFO
16#define CONFIG_SYS_MEMTEST_START 0x80000000
17#define CONFIG_SYS_MEMTEST_END 0x9fffffff
18
19
20
21
22
23
24#define I2C_MUX_IO_ADDR 0x24
25#define I2C_MUX_IO2_ADDR 0x25
26#define I2C_MUX_IO_0 0
27#define I2C_MUX_IO_1 1
28#define SW_BOOT_MASK 0x03
29#define SW_BOOT_EMU 0x02
30#define SW_BOOT_BANK1 0x00
31#define SW_BOOT_BANK2 0x01
32#define SW_REV_MASK 0xF8
33#define SW_REV_A 0xF8
34#define SW_REV_B 0xF0
35#define SW_REV_C 0xE8
36#define SW_REV_C1 0xE0
37#define SW_REV_C2 0xD8
38#define SW_REV_D 0xD0
39#define SW_REV_E 0xC8
40#define __PHY_MASK 0xF9
41#define __PHY_ETH2_MASK 0xFB
42#define __PHY_ETH1_MASK 0xFD
43
44
45#ifdef CONFIG_MMC
46#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
47#endif
48
49
50#define CONFIG_PCIE1
51
52#define CONFIG_PCI_SCAN_SHOW
53
54#define CONFIG_CMD_MEMINFO
55#define CONFIG_SYS_MEMTEST_START 0x80000000
56#define CONFIG_SYS_MEMTEST_END 0x9fffffff
57
58#undef CONFIG_EXTRA_ENV_SETTINGS
59#define CONFIG_EXTRA_ENV_SETTINGS \
60 "verify=no\0" \
61 "fdt_high=0xffffffffffffffff\0" \
62 "initrd_high=0xffffffffffffffff\0" \
63 "fdt_addr=0x00f00000\0" \
64 "kernel_addr=0x01000000\0" \
65 "kernelheader_addr=0x800000\0" \
66 "scriptaddr=0x80000000\0" \
67 "scripthdraddr=0x80080000\0" \
68 "fdtheader_addr_r=0x80100000\0" \
69 "kernelheader_addr_r=0x80200000\0" \
70 "kernel_addr_r=0x81000000\0" \
71 "fdt_addr_r=0x90000000\0" \
72 "load_addr=0xa0000000\0" \
73 "kernel_size=0x2800000\0" \
74 "kernelheader_size=0x40000\0" \
75 "console=ttyS0,115200\0" \
76 BOOTENV \
77 "boot_scripts=ls1012ardb_boot.scr\0" \
78 "boot_script_hdr=hdr_ls1012ardb_bs.out\0" \
79 "scan_dev_for_boot_part=" \
80 "part list ${devtype} ${devnum} devplist; " \
81 "env exists devplist || setenv devplist 1; " \
82 "for distro_bootpart in ${devplist}; do " \
83 "if fstype ${devtype} " \
84 "${devnum}:${distro_bootpart} " \
85 "bootfstype; then " \
86 "run scan_dev_for_boot; " \
87 "fi; " \
88 "done\0" \
89 "scan_dev_for_boot=" \
90 "echo Scanning ${devtype} " \
91 "${devnum}:${distro_bootpart}...; " \
92 "for prefix in ${boot_prefixes}; do " \
93 "run scan_dev_for_scripts; " \
94 "done;" \
95 "\0" \
96 "boot_a_script=" \
97 "load ${devtype} ${devnum}:${distro_bootpart} " \
98 "${scriptaddr} ${prefix}${script}; " \
99 "env exists secureboot && load ${devtype} " \
100 "${devnum}:${distro_bootpart} " \
101 "${scripthdraddr} ${prefix}${boot_script_hdr} " \
102 "&& esbc_validate ${scripthdraddr};" \
103 "source ${scriptaddr}\0" \
104 "installer=load mmc 0:2 $load_addr " \
105 "/flex_installer_arm64.itb; " \
106 "bootm $load_addr#$board\0" \
107 "qspi_bootcmd=echo Trying load from qspi..;" \
108 "sf probe && sf read $load_addr " \
109 "$kernel_addr $kernel_size; env exists secureboot " \
110 "&& sf read $kernelheader_addr_r $kernelheader_addr " \
111 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
112 "bootm $load_addr#$board\0"
113
114#undef CONFIG_BOOTCOMMAND
115#ifdef CONFIG_TFABOOT
116#undef QSPI_NOR_BOOTCOMMAND
117#define QSPI_NOR_BOOTCOMMAND "pfe stop; run distro_bootcmd; run qspi_bootcmd; "\
118 "env exists secureboot && esbc_halt;"
119#else
120#define CONFIG_BOOTCOMMAND "pfe stop; run distro_bootcmd; run qspi_bootcmd; "\
121 "env exists secureboot && esbc_halt;"
122#endif
123
124#include <asm/fsl_secure_boot.h>
125
126#endif
127
