1
2
3
4
5
6
7#include <common.h>
8#include <asm/io.h>
9#include <asm/arch/clock.h>
10#include <asm/arch/imx-regs.h>
11#include <asm/arch/iomux.h>
12#include <env.h>
13#include <malloc.h>
14#include <asm/arch/mx6-pins.h>
15#include <asm/mach-imx/iomux-v3.h>
16#include <asm/mach-imx/sata.h>
17#include <asm/mach-imx/mxc_i2c.h>
18#include <asm/mach-imx/boot_mode.h>
19#include <asm/arch/crm_regs.h>
20#include <asm/arch/sys_proto.h>
21#include <mmc.h>
22#include <fsl_esdhc_imx.h>
23#include <netdev.h>
24#include <i2c.h>
25#include <pca953x.h>
26#include <asm/gpio.h>
27#include <phy.h>
28
29DECLARE_GLOBAL_DATA_PTR;
30
31#define OUTPUT_40OHM (PAD_CTL_SPEED_MED|PAD_CTL_DSE_40ohm)
32
33#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
34 OUTPUT_40OHM | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
35
36#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
37 PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
38 PAD_CTL_SRE_FAST | PAD_CTL_HYS)
39
40#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | OUTPUT_40OHM | \
41 PAD_CTL_HYS)
42
43#define SPI_PAD_CTRL (PAD_CTL_HYS | OUTPUT_40OHM | \
44 PAD_CTL_SRE_FAST)
45
46#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | OUTPUT_40OHM | \
47 PAD_CTL_HYS | PAD_CTL_ODE | PAD_CTL_SRE_FAST)
48
49int dram_init(void)
50{
51 gd->ram_size = imx_ddr_size();
52
53 return 0;
54}
55
56static iomux_v3_cfg_t const uart1_pads[] = {
57 MX6_PAD_CSI0_DAT10__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
58 MX6_PAD_CSI0_DAT11__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
59};
60
61static void setup_iomux_uart(void)
62{
63 imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
64}
65
66static iomux_v3_cfg_t const enet_pads[] = {
67 MX6_PAD_KEY_ROW1__ENET_COL | MUX_PAD_CTRL(ENET_PAD_CTRL),
68 MX6_PAD_KEY_COL3__ENET_CRS | MUX_PAD_CTRL(ENET_PAD_CTRL),
69 MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
70 MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
71 MX6_PAD_GPIO_16__ENET_REF_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
72 MX6_PAD_GPIO_18__ENET_RX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
73 MX6_PAD_ENET_RXD0__ENET_RX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
74 MX6_PAD_ENET_RXD1__ENET_RX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
75 MX6_PAD_KEY_COL2__ENET_RX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
76 MX6_PAD_KEY_COL0__ENET_RX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
77 MX6_PAD_ENET_CRS_DV__ENET_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
78 MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL),
79 MX6_PAD_ENET_TXD0__ENET_TX_DATA0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
80 MX6_PAD_ENET_TXD1__ENET_TX_DATA1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
81 MX6_PAD_KEY_ROW2__ENET_TX_DATA2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
82 MX6_PAD_KEY_ROW0__ENET_TX_DATA3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
83 MX6_PAD_ENET_TX_EN__ENET_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
84};
85
86static void setup_iomux_enet(void)
87{
88 imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
89}
90
91static iomux_v3_cfg_t const ecspi1_pads[] = {
92 MX6_PAD_DISP0_DAT3__ECSPI3_SS0 | MUX_PAD_CTRL(SPI_PAD_CTRL),
93 MX6_PAD_DISP0_DAT4__ECSPI3_SS1 | MUX_PAD_CTRL(SPI_PAD_CTRL),
94 MX6_PAD_DISP0_DAT2__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
95 MX6_PAD_DISP0_DAT1__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
96 MX6_PAD_DISP0_DAT0__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
97};
98
99static void setup_iomux_spi(void)
100{
101 imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
102}
103
104int board_spi_cs_gpio(unsigned bus, unsigned cs)
105{
106 return (bus == 2 && cs == 0) ? (IMX_GPIO_NR(1, 3)) : -1;
107}
108
109static iomux_v3_cfg_t const feature_pads[] = {
110
111 MX6_PAD_GPIO_4__GPIO1_IO04 | MUX_PAD_CTRL(PAD_CTL_PUS_100K_DOWN),
112
113
114 MX6_PAD_GPIO_19__GPIO4_IO05 | MUX_PAD_CTRL(PAD_CTL_PUS_100K_UP),
115};
116
117static void setup_iomux_features(void)
118{
119 imx_iomux_v3_setup_multiple_pads(feature_pads,
120 ARRAY_SIZE(feature_pads));
121}
122
123#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
124
125
126static struct i2c_pads_info i2c_pad_info1 = {
127 .scl = {
128 .i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
129 .gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
130 .gp = IMX_GPIO_NR(2, 30)
131 },
132 .sda = {
133 .i2c_mode = MX6_PAD_EIM_D16__I2C2_SDA | PC,
134 .gpio_mode = MX6_PAD_EIM_D16__GPIO3_IO16 | PC,
135 .gp = IMX_GPIO_NR(3, 16)
136 }
137};
138
139
140static struct i2c_pads_info i2c_pad_info2 = {
141 .scl = {
142 .i2c_mode = MX6_PAD_EIM_D17__I2C3_SCL | PC,
143 .gpio_mode = MX6_PAD_EIM_D17__GPIO3_IO17 | PC,
144 .gp = IMX_GPIO_NR(3, 17)
145 },
146 .sda = {
147 .i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
148 .gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
149 .gp = IMX_GPIO_NR(3, 18)
150 }
151};
152
153static void setup_iomux_i2c(void)
154{
155 setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
156 setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
157}
158
159static void ccgr_init(void)
160{
161 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
162
163 writel(0x00C03F3F, &ccm->CCGR0);
164 writel(0x0030FC33, &ccm->CCGR1);
165 writel(0x0FFFC000, &ccm->CCGR2);
166 writel(0x3FF00000, &ccm->CCGR3);
167 writel(0x00FFF300, &ccm->CCGR4);
168 writel(0x0F0000C3, &ccm->CCGR5);
169 writel(0x000003FF, &ccm->CCGR6);
170}
171
172int board_early_init_f(void)
173{
174 ccgr_init();
175 gpr_init();
176
177 setup_iomux_uart();
178 setup_iomux_spi();
179 setup_iomux_i2c();
180 setup_iomux_features();
181
182 return 0;
183}
184
185static iomux_v3_cfg_t const usdhc3_pads[] = {
186 MX6_PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
187 MX6_PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
188 MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
189 MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
190 MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
191 MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
192 MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
193 MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
194 MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
195 MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
196 MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
197};
198
199iomux_v3_cfg_t const usdhc4_pads[] = {
200 MX6_PAD_SD4_CLK__SD4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
201 MX6_PAD_SD4_CMD__SD4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
202 MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
203 MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
204 MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
205 MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
206};
207
208int board_mmc_getcd(struct mmc *mmc)
209{
210 struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
211 int ret;
212
213 if (cfg->esdhc_base == USDHC3_BASE_ADDR) {
214 gpio_direction_input(IMX_GPIO_NR(4, 5));
215 ret = gpio_get_value(IMX_GPIO_NR(4, 5));
216 } else {
217 gpio_direction_input(IMX_GPIO_NR(1, 5));
218 ret = !gpio_get_value(IMX_GPIO_NR(1, 5));
219 }
220
221 return ret;
222}
223
224struct fsl_esdhc_cfg usdhc_cfg[2] = {
225 {USDHC3_BASE_ADDR},
226 {USDHC4_BASE_ADDR},
227};
228
229int board_mmc_init(bd_t *bis)
230{
231 int ret;
232 u32 index = 0;
233
234 usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
235 usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
236
237 usdhc_cfg[0].max_bus_width = 8;
238 usdhc_cfg[1].max_bus_width = 4;
239
240 for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) {
241 switch (index) {
242 case 0:
243 imx_iomux_v3_setup_multiple_pads(
244 usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
245 break;
246 case 1:
247 imx_iomux_v3_setup_multiple_pads(
248 usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
249 break;
250 default:
251 printf("Warning: you configured more USDHC controllers"
252 "(%d) then supported by the board (%d)\n",
253 index + 1, CONFIG_SYS_FSL_USDHC_NUM);
254 return -EINVAL;
255 }
256
257 ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]);
258 if (ret)
259 return ret;
260 }
261
262 return 0;
263}
264
265static void leds_on(void)
266{
267
268 i2c_set_bus_num(2);
269 pca953x_set_dir(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, PCA953X_DIR_OUT);
270 pca953x_set_val(CONFIG_SYS_I2C_PCA953X_ADDR, 0xffff, 0x0);
271}
272
273static void backlight_lcd_off(void)
274{
275 unsigned gpio = IMX_GPIO_NR(2, 0);
276 gpio_direction_output(gpio, 0);
277
278 gpio = IMX_GPIO_NR(2, 3);
279 gpio_direction_output(gpio, 0);
280}
281
282int board_eth_init(bd_t *bis)
283{
284 uint32_t base = IMX_FEC_BASE;
285 struct mii_dev *bus = NULL;
286 struct phy_device *phydev = NULL;
287 int ret;
288
289 setup_iomux_enet();
290
291 bus = fec_get_miibus(base, -1);
292 if (!bus)
293 return -EINVAL;
294
295
296 phydev = phy_find_by_mask(bus, 0x21, PHY_INTERFACE_MODE_RGMII);
297 if (!phydev) {
298 ret = -EINVAL;
299 goto free_bus;
300 }
301
302
303 if (phydev->addr == 0)
304 env_set("boardver", "");
305 else
306 env_set("boardver", "mr");
307
308 printf("using phy at %d\n", phydev->addr);
309 ret = fec_probe(bis, -1, base, bus, phydev);
310 if (ret)
311 goto free_phydev;
312
313 return 0;
314
315free_phydev:
316 free(phydev);
317free_bus:
318 free(bus);
319 return ret;
320}
321
322int board_init(void)
323{
324 gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
325
326 backlight_lcd_off();
327
328 leds_on();
329
330#ifdef CONFIG_SATA
331 setup_sata();
332#endif
333
334 return 0;
335}
336
337int checkboard(void)
338{
339 puts("Board: "CONFIG_SYS_BOARD"\n");
340 return 0;
341}
342
343#ifdef CONFIG_CMD_BMODE
344static const struct boot_mode board_boot_modes[] = {
345
346 {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
347 {NULL, 0},
348};
349#endif
350
351int misc_init_r(void)
352{
353#ifdef CONFIG_CMD_BMODE
354 add_board_boot_modes(board_boot_modes);
355#endif
356 return 0;
357}
358
