1source "drivers/net/phy/Kconfig"
2source "drivers/net/pfe_eth/Kconfig"
3source "drivers/net/fsl-mc/Kconfig"
4
5config DM_ETH
6 bool "Enable Driver Model for Ethernet drivers"
7 depends on DM
8 help
9 Enable driver model for Ethernet.
10
11 The eth_*() interface will be implemented by the UCLASS_ETH class
12 This is currently implemented in net/eth-uclass.c
13 Look in include/net.h for details.
14
15config DM_MDIO
16 bool "Enable Driver Model for MDIO devices"
17 depends on DM_ETH && PHYLIB
18 help
19 Enable driver model for MDIO devices
20
21 Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
22 stand-alone devices. Useful in particular for systems that support
23 DM_ETH and have a stand-alone MDIO hardware block shared by multiple
24 Ethernet interfaces.
25 This is currently implemented in net/mdio-uclass.c
26 Look in include/miiphy.h for details.
27
28config DM_MDIO_MUX
29 bool "Enable Driver Model for MDIO MUX devices"
30 depends on DM_MDIO
31 help
32 Enable driver model for MDIO MUX devices
33
34 Adds UCLASS_MDIO_MUX DM class supporting MDIO MUXes. Useful for
35 systems that support DM_MDIO and integrate one or multiple muxes on
36 the MDIO bus.
37 This is currently implemented in net/mdio-mux-uclass.c
38 Look in include/miiphy.h for details.
39
40config MDIO_SANDBOX
41 depends on DM_MDIO && SANDBOX
42 default y
43 bool "Sandbox: Mocked MDIO driver"
44 help
45 This driver implements dummy read/write/reset MDIO functions mimicking
46 a bus with a single PHY.
47
48 This driver is used in for testing in test/dm/mdio.c
49
50config MDIO_MUX_SANDBOX
51 depends on DM_MDIO_MUX && MDIO_SANDBOX
52 default y
53 bool "Sandbox: Mocked MDIO-MUX driver"
54 help
55 This driver implements dummy select/deselect ops mimicking a MUX on
56 the MDIO bux. It uses mdio_sandbox driver as parent MDIO.
57
58 This driver is used for testing in test/dm/mdio.c
59
60config DM_ETH_PHY
61 bool "Enable Driver Model for Ethernet Generic PHY drivers"
62 depends on DM
63 help
64 Enable driver model for Ethernet Generic PHY .
65
66menuconfig NETDEVICES
67 bool "Network device support"
68 depends on NET
69 default y if DM_ETH
70 help
71 You must select Y to enable any network device support
72 Generally if you have any networking support this is a given
73
74 If unsure, say Y
75
76if NETDEVICES
77
78config PHY_GIGE
79 bool "Enable GbE PHY status parsing and configuration"
80 help
81 Enables support for parsing the status output and for
82 configuring GbE PHYs (affects the inner workings of some
83 commands and miiphyutil.c).
84
85config AG7XXX
86 bool "Atheros AG7xxx Ethernet MAC support"
87 depends on DM_ETH && ARCH_ATH79
88 select PHYLIB
89 help
90 This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
91 present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
92
93
94config ALTERA_TSE
95 bool "Altera Triple-Speed Ethernet MAC support"
96 depends on DM_ETH
97 select PHYLIB
98 help
99 This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
100 Please find details on the "Triple-Speed Ethernet MegaCore Function
101 Resource Center" of Altera.
102
103config BCM_SF2_ETH
104 bool "Broadcom SF2 (Starfighter2) Ethernet support"
105 select PHYLIB
106 help
107 This is an abstract framework which provides a generic interface
108 to MAC and DMA management for multiple Broadcom SoCs such as
109 Cygnus, NSP and bcm28155_ap platforms.
110
111config BCM_SF2_ETH_DEFAULT_PORT
112 int "Broadcom SF2 (Starfighter2) Ethernet default port number"
113 depends on BCM_SF2_ETH
114 default 0
115 help
116 Default port number for the Starfighter2 ethernet driver.
117
118config BCM_SF2_ETH_GMAC
119 bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
120 depends on BCM_SF2_ETH
121 help
122 This flag enables the ethernet support for Broadcom platforms with
123 GMAC such as Cygnus. This driver is based on the framework provided
124 by the BCM_SF2_ETH driver.
125 Say Y to any bcmcygnus based platforms.
126
127config BCM6348_ETH
128 bool "BCM6348 EMAC support"
129 depends on DM_ETH && ARCH_BMIPS
130 select DMA
131 select DMA_CHANNELS
132 select MII
133 select PHYLIB
134 help
135 This driver supports the BCM6348 Ethernet MAC.
136
137config BCM6368_ETH
138 bool "BCM6368 EMAC support"
139 depends on DM_ETH && ARCH_BMIPS
140 select DMA
141 select MII
142 help
143 This driver supports the BCM6368 Ethernet MAC.
144
145config BCMGENET
146 bool "BCMGENET V5 support"
147 depends on DM_ETH
148 select PHYLIB
149 help
150 This driver supports the BCMGENET Ethernet MAC.
151
152config DWC_ETH_QOS
153 bool "Synopsys DWC Ethernet QOS device support"
154 depends on DM_ETH
155 select PHYLIB
156 help
157 This driver supports the Synopsys Designware Ethernet QOS (Quality
158 Of Service) IP block. The IP supports many options for bus type,
159 clocking/reset structure, and feature list.
160
161config DWC_ETH_QOS_IMX
162 bool "Synopsys DWC Ethernet QOS device support for IMX"
163 depends on DWC_ETH_QOS
164 help
165 The Synopsys Designware Ethernet QOS IP block with the specific
166 configuration used in IMX soc.
167
168config DWC_ETH_QOS_STM32
169 bool "Synopsys DWC Ethernet QOS device support for STM32"
170 depends on DWC_ETH_QOS
171 default y if ARCH_STM32MP
172 help
173 The Synopsys Designware Ethernet QOS IP block with the specific
174 configuration used in STM32MP soc.
175
176config DWC_ETH_QOS_TEGRA186
177 bool "Synopsys DWC Ethernet QOS device support for TEGRA186"
178 depends on DWC_ETH_QOS
179 default y if TEGRA186
180 help
181 The Synopsys Designware Ethernet QOS IP block with specific
182 configuration used in NVIDIA's Tegra186 chip.
183
184config E1000
185 bool "Intel PRO/1000 Gigabit Ethernet support"
186 depends on (DM_ETH && DM_PCI) || !DM_ETH
187 help
188 This driver supports Intel(R) PRO/1000 gigabit ethernet family of
189 adapters. For more information on how to identify your adapter, go
190 to the Adapter & Driver ID Guide at:
191
192 <http://support.intel.com/support/network/adapter/pro100/21397.htm>
193
194config E1000_SPI_GENERIC
195 bool "Allow access to the Intel 8257x SPI bus"
196 depends on E1000
197 help
198 Allow generic access to the SPI bus on the Intel 8257x, for
199 example with the "sspi" command.
200
201config E1000_SPI
202 bool "Enable SPI bus utility code"
203 depends on E1000
204 help
205 Utility code for direct access to the SPI bus on Intel 8257x.
206 This does not do anything useful unless you set at least one
207 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
208
209config CMD_E1000
210 bool "Enable the e1000 command"
211 depends on E1000
212 help
213 This enables the 'e1000' management command for E1000 devices. When
214 used on devices with SPI support you can reprogram the EEPROM from
215 U-Boot.
216
217config EEPRO100
218 bool "Intel PRO/100 82557/82559/82559ER Fast Ethernet support"
219 help
220 This driver supports Intel(R) PRO/100 82557/82559/82559ER fast
221 ethernet family of adapters.
222
223config ETH_SANDBOX
224 depends on DM_ETH && SANDBOX
225 default y
226 bool "Sandbox: Mocked Ethernet driver"
227 help
228 This driver simply responds with fake ARP replies and ping
229 replies that are used to verify network stack functionality
230
231 This driver is particularly useful in the test/dm/eth.c tests
232
233config ETH_SANDBOX_RAW
234 depends on DM_ETH && SANDBOX
235 default y
236 bool "Sandbox: Bridge to Linux Raw Sockets"
237 help
238 This driver is a bridge from the bottom of the network stack
239 in U-Boot to the RAW AF_PACKET API in Linux. This allows real
240 network traffic to be tested from within sandbox. See
241 doc/arch/index.rst for more details.
242
243config ETH_DESIGNWARE
244 bool "Synopsys Designware Ethernet MAC"
245 select PHYLIB
246 imply ETH_DESIGNWARE_SOCFPGA if ARCH_SOCFPGA
247 help
248 This MAC is present in SoCs from various vendors. It supports
249 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
250 provide the PHY (physical media interface).
251
252config ETH_DESIGNWARE_SOCFPGA
253 select REGMAP
254 select SYSCON
255 bool "Altera SoCFPGA extras for Synopsys Designware Ethernet MAC"
256 depends on DM_ETH && ETH_DESIGNWARE
257 help
258 The Altera SoCFPGA requires additional configuration of the
259 Altera system manager to correctly interface with the PHY.
260 This code handles those SoC specifics.
261
262config ETH_DESIGNWARE_S700
263 bool "Actins S700 glue driver for Synopsys Designware Ethernet MAC"
264 depends on DM_ETH && ETH_DESIGNWARE
265 help
266 This provides glue layer to use Synopsys Designware Ethernet MAC
267 present on Actions S700 SoC.
268
269config ETHOC
270 bool "OpenCores 10/100 Mbps Ethernet MAC"
271 help
272 This MAC is present in OpenRISC and Xtensa XTFPGA boards.
273
274config FEC_MXC_SHARE_MDIO
275 bool "Share the MDIO bus for FEC controller"
276 depends on FEC_MXC
277
278config FEC_MXC_MDIO_BASE
279 hex "MDIO base address for the FEC controller"
280 depends on FEC_MXC_SHARE_MDIO
281 help
282 This specifies the MDIO registers base address. It is used when
283 two FEC controllers share MDIO bus.
284
285config FEC_MXC
286 bool "FEC Ethernet controller"
287 depends on MX28 || MX5 || MX6 || MX7 || IMX8 || IMX8M || VF610
288 help
289 This driver supports the 10/100 Fast Ethernet controller for
290 NXP i.MX processors.
291
292config FMAN_ENET
293 bool "Freescale FMan ethernet support"
294 depends on ARM || PPC
295 help
296 This driver support the Freescale FMan Ethernet controller
297
298config FTMAC100
299 bool "Ftmac100 Ethernet Support"
300 help
301 This MAC is present in Andestech SoCs.
302
303config FTGMAC100
304 bool "Ftgmac100 Ethernet Support"
305 depends on DM_ETH
306 select PHYLIB
307 help
308 This driver supports the Faraday's FTGMAC100 Gigabit SoC
309 Ethernet controller that can be found on Aspeed SoCs (which
310 include NCSI).
311
312 It is fully compliant with IEEE 802.3 specification for
313 10/100 Mbps Ethernet and IEEE 802.3z specification for 1000
314 Mbps Ethernet and includes Reduced Media Independent
315 Interface (RMII) and Reduced Gigabit Media Independent
316 Interface (RGMII) interfaces. It adopts an AHB bus interface
317 and integrates a link list DMA engine with direct M-Bus
318 accesses for transmitting and receiving packets. It has
319 independent TX/RX fifos, supports half and full duplex (1000
320 Mbps mode only supports full duplex), flow control for full
321 duplex and backpressure for half duplex.
322
323 The FTGMAC100 also implements IP, TCP, UDP checksum offloads
324 and supports IEEE 802.1Q VLAN tag insertion and removal. It
325 offers high-priority transmit queue for QoS and CoS
326 applications.
327
328
329config MCFFEC
330 bool "ColdFire Ethernet Support"
331 depends on DM_ETH
332 select PHYLIB
333 help
334 This driver supports the network interface units in the
335 ColdFire family.
336
337config FSLDMAFEC
338 bool "ColdFire DMA Ethernet Support"
339 depends on DM_ETH
340 select PHYLIB
341 help
342 This driver supports the network interface units in the
343 ColdFire family.
344
345config KS8851_MLL
346 bool "Microchip KS8851-MLL controller driver"
347 help
348 The Microchip KS8851 parallel bus external ethernet interface chip.
349
350if KS8851_MLL
351if !DM_ETH
352config KS8851_MLL_BASEADDR
353 hex "Microchip KS8851-MLL Base Address"
354 help
355 Define this to hold the physical address of the device (I/O space)
356endif
357endif
358
359config MVGBE
360 bool "Marvell Orion5x/Kirkwood network interface support"
361 depends on ARCH_KIRKWOOD || ARCH_ORION5X
362 select PHYLIB if DM_ETH
363 help
364 This driver supports the network interface units in the
365 Marvell Orion5x and Kirkwood SoCs
366
367config MVNETA
368 bool "Marvell Armada XP/385/3700 network interface support"
369 depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
370 select PHYLIB
371 help
372 This driver supports the network interface units in the
373 Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs
374
375config MVPP2
376 bool "Marvell Armada 375/7K/8K network interface support"
377 depends on ARMADA_375 || ARMADA_8K
378 select PHYLIB
379 select MVMDIO
380 select DM_MDIO
381 help
382 This driver supports the network interface units in the
383 Marvell ARMADA 375, 7K and 8K SoCs.
384
385config MACB
386 bool "Cadence MACB/GEM Ethernet Interface"
387 depends on DM_ETH
388 select PHYLIB
389 help
390 The Cadence MACB ethernet interface is found on many Atmel
391 AT91 and SAMA5 parts. This driver also supports the Cadence
392 GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
393 Say Y to include support for the MACB/GEM chip.
394
395config MACB_ZYNQ
396 bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq"
397 depends on MACB
398 help
399 The Cadence MACB ethernet interface was used on Zynq platform.
400 Say Y to enable support for the MACB/GEM in Zynq chip.
401
402config MT7628_ETH
403 bool "MediaTek MT7628 Ethernet Interface"
404 depends on SOC_MT7628
405 select PHYLIB
406 help
407 The MediaTek MT7628 ethernet interface is used on MT7628 and
408 MT7688 based boards.
409
410config NET_OCTEONTX
411 bool "OcteonTX Ethernet support"
412 depends on ARCH_OCTEONTX
413 depends on PCI_SRIOV
414 help
415 You must select Y to enable network device support for
416 OcteonTX SoCs. If unsure, say n
417
418config NET_OCTEONTX2
419 bool "OcteonTX2 Ethernet support"
420 depends on ARCH_OCTEONTX2
421 select OCTEONTX2_CGX_INTF
422 help
423 You must select Y to enable network device support for
424 OcteonTX2 SoCs. If unsure, say n
425
426config OCTEONTX_SMI
427 bool "OcteonTX SMI Device support"
428 depends on ARCH_OCTEONTX || ARCH_OCTEONTX2
429 help
430 You must select Y to enable SMI controller support for
431 OcteonTX or OcteonTX2 SoCs. If unsure, say n
432
433config OCTEONTX2_CGX_INTF
434 bool "OcteonTX2 CGX ATF interface support"
435 depends on ARCH_OCTEONTX2
436 default y if ARCH_OCTEONTX2
437 help
438 You must select Y to enable CGX ATF interface support for
439 OcteonTX2 SoCs. If unsure, say n
440
441config PCH_GBE
442 bool "Intel Platform Controller Hub EG20T GMAC driver"
443 depends on DM_ETH && DM_PCI
444 select PHYLIB
445 help
446 This MAC is present in Intel Platform Controller Hub EG20T. It
447 supports 10/100/1000 Mbps operation.
448
449config RGMII
450 bool "Enable RGMII"
451 help
452 Enable the support of the Reduced Gigabit Media-Independent
453 Interface (RGMII).
454
455config MII
456 bool "Enable MII"
457 help
458 Enable support of the Media-Independent Interface (MII)
459
460config PCNET
461 bool "AMD PCnet series Ethernet controller driver"
462 help
463 This driver supports AMD PCnet series fast ethernet family of
464 PCI chipsets/adapters.
465
466source "drivers/net/qe/Kconfig"
467
468config RTL8139
469 bool "Realtek 8139 series Ethernet controller driver"
470 help
471 This driver supports Realtek 8139 series fast ethernet family of
472 PCI chipsets/adapters.
473
474config RTL8169
475 bool "Realtek 8169 series Ethernet controller driver"
476 help
477 This driver supports Realtek 8169 series gigabit ethernet family of
478 PCI/PCIe chipsets/adapters.
479
480config SMC911X
481 bool "SMSC LAN911x and LAN921x controller driver"
482
483if SMC911X
484
485if !DM_ETH
486config SMC911X_BASE
487 hex "SMC911X Base Address"
488 help
489 Define this to hold the physical address
490 of the device (I/O space)
491endif
492
493choice
494 prompt "SMC911X bus width"
495 default SMC911X_16_BIT
496
497config SMC911X_32_BIT
498 bool "Enable 32-bit interface"
499
500config SMC911X_16_BIT
501 bool "Enable 16-bit interface"
502 help
503 Define this if data bus is 16 bits. If your processor
504 automatically converts one 32 bit word to two 16 bit
505 words you may also try CONFIG_SMC911X_32_BIT.
506
507endchoice
508endif
509
510config SUN7I_GMAC
511 bool "Enable Allwinner GMAC Ethernet support"
512 help
513 Enable the support for Sun7i GMAC Ethernet controller
514
515config SUN7I_GMAC_FORCE_TXERR
516 bool "Force PA17 as gmac function"
517 depends on SUN7I_GMAC
518 help
519 Some ethernet phys needs TXERR control. Since the GMAC
520 doesn't have such signal, setting PA17 as GMAC function
521 makes the pin output low, which enables data transmission.
522
523config SUN4I_EMAC
524 bool "Allwinner Sun4i Ethernet MAC support"
525 depends on DM_ETH
526 select PHYLIB
527 help
528 This driver supports the Allwinner based SUN4I Ethernet MAC.
529
530config SUN8I_EMAC
531 bool "Allwinner Sun8i Ethernet MAC support"
532 depends on DM_ETH
533 select PHYLIB
534 select PHY_GIGE
535 help
536 This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC.
537 It can be found in H3/A64/A83T based SoCs and compatible with both
538 External and Internal PHYs.
539
540config SH_ETHER
541 bool "Renesas SH Ethernet MAC"
542 select PHYLIB
543 help
544 This driver supports the Ethernet for Renesas SH and ARM SoCs.
545
546source "drivers/net/ti/Kconfig"
547
548config TULIP
549 bool "DEC Tulip DC2114x Ethernet support"
550 depends on (DM_ETH && DM_PCI) || !DM_ETH
551 help
552 This driver supports DEC DC2114x Fast ethernet chips.
553
554config XILINX_AXIEMAC
555 depends on DM_ETH
556 select PHYLIB
557 select MII
558 bool "Xilinx AXI Ethernet"
559 help
560 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
561
562config XILINX_EMACLITE
563 depends on DM_ETH
564 select PHYLIB
565 select MII
566 bool "Xilinx Ethernetlite"
567 help
568 This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
569
570config ZYNQ_GEM
571 depends on DM_ETH
572 select PHYLIB
573 bool "Xilinx Ethernet GEM"
574 help
575 This MAC is present in Xilinx Zynq and ZynqMP SoCs.
576
577config PIC32_ETH
578 bool "Microchip PIC32 Ethernet Support"
579 depends on DM_ETH && MACH_PIC32
580 select PHYLIB
581 help
582 This driver implements 10/100 Mbps Ethernet and MAC layer for
583 Microchip PIC32 microcontrollers.
584
585config GMAC_ROCKCHIP
586 bool "Rockchip Synopsys Designware Ethernet MAC"
587 depends on DM_ETH && ETH_DESIGNWARE
588 help
589 This driver provides Rockchip SoCs network support based on the
590 Synopsys Designware driver.
591
592config RENESAS_RAVB
593 bool "Renesas Ethernet AVB MAC"
594 depends on DM_ETH && RCAR_GEN3
595 select PHYLIB
596 help
597 This driver implements support for the Ethernet AVB block in
598 Renesas M3 and H3 SoCs.
599
600config MPC8XX_FEC
601 bool "Fast Ethernet Controller on MPC8XX"
602 depends on MPC8xx
603 select MII
604 help
605 This driver implements support for the Fast Ethernet Controller
606 on MPC8XX
607
608config SNI_AVE
609 bool "Socionext AVE Ethernet support"
610 depends on DM_ETH && ARCH_UNIPHIER
611 select PHYLIB
612 select SYSCON
613 select REGMAP
614 help
615 This driver implements support for the Socionext AVE Ethernet
616 controller, as found on the Socionext UniPhier family.
617
618source "drivers/net/mscc_eswitch/Kconfig"
619
620config ETHER_ON_FEC1
621 bool "FEC1"
622 depends on MPC8XX_FEC
623 default y
624
625config FEC1_PHY
626 int "FEC1 PHY"
627 depends on ETHER_ON_FEC1
628 default -1
629 help
630 Define to the hardcoded PHY address which corresponds
631 to the given FEC; i. e.
632 #define CONFIG_FEC1_PHY 4
633 means that the PHY with address 4 is connected to FEC1
634
635 When set to -1, means to probe for first available.
636
637config PHY_NORXERR
638 bool "PHY_NORXERR"
639 depends on ETHER_ON_FEC1
640 default n
641 help
642 The PHY does not have a RXERR line (RMII only).
643 (so program the FEC to ignore it).
644
645config ETHER_ON_FEC2
646 bool "FEC2"
647 depends on MPC8XX_FEC && MPC885
648 default y
649
650config FEC2_PHY
651 int "FEC2 PHY"
652 depends on ETHER_ON_FEC2
653 default -1
654 help
655 Define to the hardcoded PHY address which corresponds
656 to the given FEC; i. e.
657 #define CONFIG_FEC1_PHY 4
658 means that the PHY with address 4 is connected to FEC1
659
660 When set to -1, means to probe for first available.
661
662config FEC2_PHY_NORXERR
663 bool "PHY_NORXERR"
664 depends on ETHER_ON_FEC2
665 default n
666 help
667 The PHY does not have a RXERR line (RMII only).
668 (so program the FEC to ignore it).
669
670config SYS_DPAA_QBMAN
671 bool "Device tree fixup for QBMan on freescale SOCs"
672 depends on (ARM || PPC) && !SPL_BUILD
673 default y if ARCH_B4860 || \
674 ARCH_B4420 || \
675 ARCH_P1023 || \
676 ARCH_P2041 || \
677 ARCH_T1023 || \
678 ARCH_T1024 || \
679 ARCH_T1040 || \
680 ARCH_T1042 || \
681 ARCH_T2080 || \
682 ARCH_T2081 || \
683 ARCH_T4240 || \
684 ARCH_T4160 || \
685 ARCH_P4080 || \
686 ARCH_P3041 || \
687 ARCH_P5040 || \
688 ARCH_P5020 || \
689 ARCH_LS1043A || \
690 ARCH_LS1046A
691 help
692 QBman fixups to allow deep sleep in DPAA 1 SOCs
693
694config TSEC_ENET
695 select PHYLIB
696 bool "Enable Three-Speed Ethernet Controller"
697 help
698 This driver implements support for the (Enhanced) Three-Speed
699 Ethernet Controller found on Freescale SoCs.
700
701config MEDIATEK_ETH
702 bool "MediaTek Ethernet GMAC Driver"
703 depends on DM_ETH
704 select PHYLIB
705 select DM_GPIO
706 select DM_RESET
707 help
708 This Driver support MediaTek Ethernet GMAC
709 Say Y to enable support for the MediaTek Ethernet GMAC.
710
711config HIGMACV300_ETH
712 bool "HiSilicon Gigabit Ethernet Controller"
713 depends on DM_ETH
714 select DM_RESET
715 select PHYLIB
716 help
717 This driver supports HIGMACV300 Ethernet controller found on
718 HiSilicon SoCs.
719
720config FSL_ENETC
721 bool "NXP ENETC Ethernet controller"
722 depends on DM_PCI && DM_ETH && DM_MDIO
723 help
724 This driver supports the NXP ENETC Ethernet controller found on some
725 of the NXP SoCs.
726
727config MDIO_MUX_I2CREG
728 bool "MDIO MUX accessed as a register over I2C"
729 depends on DM_MDIO_MUX && DM_I2C
730 help
731 This driver is used for MDIO muxes driven by writing to a register of
732 an I2C chip. The board it was developed for uses a mux controlled by
733 on-board FPGA which in turn is accessed as a chip over I2C.
734
735config MDIO_IPQ4019
736 bool "Qualcomm IPQ4019 MDIO interface support"
737 depends on DM_MDIO
738 help
739 This driver supports the MDIO interface found in Qualcomm
740 IPQ40xx series Soc-s.
741
742config MVMDIO
743 bool "Marvell MDIO interface support"
744 depends on DM_MDIO
745 help
746 This driver supports the MDIO interface found in the network
747 interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
748 Dove, Armada 370, Armada XP, Armada 37xx and Armada7K/8K/8KP).
749
750 This driver is used by the MVPP2 and MVNETA drivers.
751
752config FSL_LS_MDIO
753 bool "NXP Layerscape MDIO interface support"
754 depends on DM_MDIO
755 help
756 This driver supports the MDIO bus found on the Fman 10G Ethernet MACs and
757 on the mEMAC (which supports both Clauses 22 and 45).
758
759endif
760
