1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz> 4 */ 5 6#ifndef _CONFIG_SBX81LIFKW_H 7#define _CONFIG_SBX81LIFKW_H 8 9/* 10 * High Level Configuration Options (easy to change) 11 */ 12#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */ 13#define CONFIG_KW88F6281 1 /* SOC Name */ 14#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ 15#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg 16 17/* additions for new ARM relocation support */ 18#define CONFIG_SYS_SDRAM_BASE 0x00000000 19 20#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ 21#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ 22#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */ 23#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ 24#define CONFIG_KIRKWOOD_GPIO 1 25 26/* 27 * NS16550 Configuration 28 */ 29#define CONFIG_SYS_NS16550 30#define CONFIG_SYS_NS16550_SERIAL 31#define CONFIG_SYS_NS16550_REG_SIZE (-4) 32#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK 33#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE 34 35/* 36 * Serial Port configuration 37 * The following definitions let you select what serial you want to use 38 * for your console driver. 39 */ 40 41/* 42 * For booting Linux, the board info and command line data 43 * have to be in the first 8 MB of memory, since this is 44 * the maximum mapped by the Linux kernel during initialization. 45 */ 46#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ 47#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */ 48#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */ 49 50#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)" 51#define MTDPARTS_MTDOOPS "errlog" 52#define CONFIG_DOS_PARTITION 53 54/* 55 * Environment variables configurations 56 */ 57 58/* 59 * U-Boot bootcode configuration 60 */ 61 62#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */ 63#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */ 64 65/* 66 * For booting Linux, the board info and command line data 67 * have to be in the first 8 MB of memory, since this is 68 * the maximum mapped by the Linux kernel during initialization. 69 */ 70#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/ 71 72/* size in bytes reserved for initial data */ 73 74#include <asm/arch/config.h> 75/* There is no PHY directly connected so don't ask it for link status */ 76#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN 77 78/* 79 * Other required minimal configurations 80 */ 81#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ 82 83/* 84 * Ethernet Driver configuration 85 */ 86#ifdef CONFIG_CMD_NET 87#define CONFIG_NET_MULTI /* specify more that one ports available */ 88#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */ 89#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */ 90#define CONFIG_PHY_BASE_ADR 0x01 91#endif /* CONFIG_CMD_NET */ 92 93#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */ 94 95#endif /* _CONFIG_SBX81LIFKW_H */ 96