/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2014 Freescale Semiconductor, Inc.
 * Copyright 2020 NXP
 */

/*
 * T2080 RDB/PCIe board configuration file
 */

#ifndef __T2080RDB_H
#define __T2080RDB_H

#include <linux/stringify.h>

#define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
#define CONFIG_FSL_SATA_V2

/* High Level Configuration Options */
#define CONFIG_SYS_BOOK3E_HV    /* Category E.HV supported */
#define CONFIG_ENABLE_36BIT_PHYS

#define CONFIG_SYS_FSL_CPC      /* Corenet Platform Cache */
#define CONFIG_SYS_NUM_CPC      CONFIG_SYS_NUM_DDR_CTLRS

#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t208xrdb/t2080_pbi.cfg

#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_PAD_TO               0x40000
#define CONFIG_SPL_MAX_SIZE             0x28000
#define RESET_VECTOR_OFFSET             0x27FFC
#define BOOT_PAGE_OFFSET                0x27000
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SPL_SKIP_RELOCATE
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
#endif

#ifdef CONFIG_MTD_RAW_NAND
#define CONFIG_SYS_NAND_U_BOOT_SIZE     (768 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST      0x00200000
#define CONFIG_SYS_NAND_U_BOOT_START    0x00200000
#define CONFIG_SYS_NAND_U_BOOT_OFFS     (256 << 10)
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_nand_rcw.cfg
#endif

#ifdef CONFIG_SPIFLASH
#define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
#define CONFIG_SPL_SPI_FLASH_MINIMAL
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE       (768 << 10)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST                (0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START      (0x00200000)
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS       (256 << 10)
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_spi_rcw.cfg
#endif

#ifdef CONFIG_SDCARD
#define        CONFIG_RESET_VECTOR_ADDRESS             0x200FFC
#define CONFIG_SYS_MMC_U_BOOT_SIZE     (768 << 10)
#define CONFIG_SYS_MMC_U_BOOT_DST      (0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_START    (0x00200000)
#define CONFIG_SYS_MMC_U_BOOT_OFFS     (260 << 10)
#ifndef CONFIG_SPL_BUILD
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#endif
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t208xrdb/t2080_sd_rcw.cfg
#endif

#endif /* CONFIG_RAMBOOT_PBL */

#define CONFIG_SRIO_PCIE_BOOT_MASTER
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
/* Set 1M boot space */
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
#endif

#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
#endif

/*
 * These can be toggled for performance analysis, otherwise use default.
 */
#define CONFIG_SYS_CACHE_STASHING
#define CONFIG_BTB              /* toggle branch predition */
#define CONFIG_DDR_ECC
#ifdef CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_MEM_INIT_VALUE           0xdeadbeef
#endif

#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#endif

#define CONFIG_SYS_CLK_FREQ     66660000
#define CONFIG_DDR_CLK_FREQ     133330000

/*
 * Config the L3 Cache as L3 SRAM
 */
#define CONFIG_SYS_INIT_L3_ADDR         0xFFFC0000
#define CONFIG_SYS_L3_SIZE              (512 << 10)
#define CONFIG_SPL_GD_ADDR              (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
#define SPL_ENV_ADDR                    (CONFIG_SPL_GD_ADDR + 4 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_ADDR    (CONFIG_SPL_GD_ADDR + 12 * 1024)
#define CONFIG_SPL_RELOC_MALLOC_SIZE    (50 << 10)
#define CONFIG_SPL_RELOC_STACK          (CONFIG_SPL_GD_ADDR + 64 * 1024)

#define CONFIG_SYS_DCSRBAR      0xf0000000
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull

/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM       0
#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2

/*
 * DDR Setup
 */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_DIMM_SLOTS_PER_CTLR      1
#define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM  0
#define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1     0x51
#define SPD_EEPROM_ADDRESS2     0x52
#define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
#define CTRL_INTLV_PREFERED     cacheline

/*
 * IFC Definitions
 */
#define CONFIG_SYS_FLASH_BASE           0xe8000000
#define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
#define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
                                CSPR_PORT_SIZE_16 | \
                                CSPR_MSEL_NOR | \
                                CSPR_V)
#define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128*1024*1024)

/* NOR Flash Timing Params */
#define CONFIG_SYS_NOR_CSOR     CSOR_NAND_TRHZ_80

#define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
                                FTIM0_NOR_TEADC(0x5) | \
                                FTIM0_NOR_TEAHC(0x5))
#define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
                                FTIM1_NOR_TRAD_NOR(0x1A) |\
                                FTIM1_NOR_TSEQRAD_NOR(0x13))
#define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
                                FTIM2_NOR_TCH(0x4) | \
                                FTIM2_NOR_TWPH(0x0E) | \
                                FTIM2_NOR_TWP(0x1c))
#define CONFIG_SYS_NOR_FTIM3    0x0

#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */

#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS }

/* CPLD on IFC */
#define CONFIG_SYS_CPLD_BASE    0xffdf0000
#define CONFIG_SYS_CPLD_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
#define CONFIG_SYS_CSPR2_EXT    (0xf)
#define CONFIG_SYS_CSPR2        (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
                                | CSPR_PORT_SIZE_8 \
                                | CSPR_MSEL_GPCM \
                                | CSPR_V)
#define CONFIG_SYS_AMASK2       IFC_AMASK(64*1024)
#define CONFIG_SYS_CSOR2        0x0

/* CPLD Timing parameters for IFC CS2 */
#define CONFIG_SYS_CS2_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
                                        FTIM0_GPCM_TEADC(0x0e) | \
                                        FTIM0_GPCM_TEAHC(0x0e))
#define CONFIG_SYS_CS2_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
                                        FTIM1_GPCM_TRAD(0x1f))
#define CONFIG_SYS_CS2_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
                                        FTIM2_GPCM_TCH(0x8) | \
                                        FTIM2_GPCM_TWP(0x1f))
#define CONFIG_SYS_CS2_FTIM3            0x0

/* NAND Flash on IFC */
#define CONFIG_NAND_FSL_IFC
#define CONFIG_SYS_NAND_BASE            0xff800000
#define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)

#define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
#define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
                                | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
                                | CSPR_MSEL_NAND         /* MSEL = NAND */ \
                                | CSPR_V)
#define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64*1024)

#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
                                | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
                                | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */     \
                                | CSOR_NAND_RAL_3       /* RAL = 2Byes */   \
                                | CSOR_NAND_PGS_2K      /* Page Size = 2K */\
                                | CSOR_NAND_SPRZ_64     /* Spare size = 64 */\
                                | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/

#define CONFIG_SYS_NAND_ONFI_DETECTION

/* ONFI NAND Flash mode0 Timing Params */
#define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
                                        FTIM0_NAND_TWP(0x18)    | \
                                        FTIM0_NAND_TWCHT(0x07)  | \
                                        FTIM0_NAND_TWH(0x0a))
#define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
                                        FTIM1_NAND_TWBE(0x39)   | \
                                        FTIM1_NAND_TRR(0x0e)    | \
                                        FTIM1_NAND_TRP(0x18))
#define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f)  | \
                                        FTIM2_NAND_TREH(0x0a)   | \
                                        FTIM2_NAND_TWHRE(0x1e))
#define CONFIG_SYS_NAND_FTIM3           0x0

#define CONFIG_SYS_NAND_DDR_LAW         11
#define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE      1
#define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)

#if defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
#define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
#else
#define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
#define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
#define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
#define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
#define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
#define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
#define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
#define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
#define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NAND_CSPR_EXT
#define CONFIG_SYS_CSPR1                CONFIG_SYS_NAND_CSPR
#define CONFIG_SYS_AMASK1               CONFIG_SYS_NAND_AMASK
#define CONFIG_SYS_CSOR1                CONFIG_SYS_NAND_CSOR
#define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NAND_FTIM0
#define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NAND_FTIM1
#define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NAND_FTIM3
#endif

#if defined(CONFIG_RAMBOOT_PBL)
#define CONFIG_SYS_RAMBOOT
#endif

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MONITOR_BASE  CONFIG_SPL_TEXT_BASE
#else
#define CONFIG_SYS_MONITOR_BASE  CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif

#define CONFIG_HWCONFIG

/* define to use L1 as initial stack */
#define CONFIG_L1_INIT_RAM
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000 /* Initial L1 address */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe03c000
/* The assembler doesn't like typecast */
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
                        ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
                        CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
#define CONFIG_SYS_INIT_RAM_SIZE        0x00004000
#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
                                                GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN          (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)

/*
 * Serial Port
 */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
#define CONFIG_SYS_BAUDRATE_TABLE       \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)

/*
 * I2C
 */
#ifndef CONFIG_DM_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
#define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
#define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
#define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
#define CONFIG_SYS_FSL_I2C_SPEED   100000
#define CONFIG_SYS_FSL_I2C2_SPEED  100000
#define CONFIG_SYS_FSL_I2C3_SPEED  100000
#define CONFIG_SYS_FSL_I2C4_SPEED  100000
#else
#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
#define CONFIG_I2C_DEFAULT_BUS_NUMBER   0
#endif

#define CONFIG_SYS_I2C_FSL

#define I2C_MUX_PCA_ADDR_PRI    0x77 /* I2C bus multiplexer,primary */
#define I2C_MUX_PCA_ADDR_SEC1   0x75 /* I2C bus multiplexer,secondary 1 */
#define I2C_MUX_PCA_ADDR_SEC2   0x76 /* I2C bus multiplexer,secondary 2 */
#define I2C_MUX_CH_DEFAULT      0x8

#define I2C_MUX_CH_VOL_MONITOR  0xa

#define CONFIG_VID_FLS_ENV              "t208xrdb_vdd_mv"
#ifndef CONFIG_SPL_BUILD
#define CONFIG_VID
#endif
#define CONFIG_VOL_MONITOR_IR36021_SET
#define CONFIG_VOL_MONITOR_IR36021_READ
/* The lowest and highest voltage allowed for T208xRDB */
#define VDD_MV_MIN                      819
#define VDD_MV_MAX                      1212

/*
 * RapidIO
 */
#define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
#define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
#define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000 /* 256M */
#define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
#define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
#define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000 /* 256M */
/*
 * for slave u-boot IMAGE instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x100000 /* 1M */
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
/*
 * for slave UCODE and ENV instored in master memory space,
 * PHYS must be aligned based on the SIZE
 */
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000 /* 256K */

/* slave core release by master*/
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */

/*
 * SRIO_PCIE_BOOT - SLAVE
 */
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
                (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
#endif

/*
 * eSPI - Enhanced SPI
 */

/*
 * General PCI
 * Memory space is mapped 1-1, but I/O space must start from 0.
 */
#define CONFIG_PCIE1            /* PCIE controller 1 */
#define CONFIG_PCIE2            /* PCIE controller 2 */
#define CONFIG_PCIE3            /* PCIE controller 3 */
#define CONFIG_PCIE4            /* PCIE controller 4 */
#define CONFIG_SYS_PCI_64BIT    /* enable 64-bit PCI resources */
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
#define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
#define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
#define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull

/* controller 2, Slot 2, tgtid 2, Base address 201000 */
#define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
#define CONFIG_SYS_PCIE2_IO_VIRT        0xf8010000
#define CONFIG_SYS_PCIE2_IO_PHYS        0xff8010000ull

/* controller 3, Slot 1, tgtid 1, Base address 202000 */
#define CONFIG_SYS_PCIE3_MEM_VIRT       0xb0000000
#define CONFIG_SYS_PCIE3_MEM_PHYS       0xc30000000ull
#define CONFIG_SYS_PCIE3_IO_VIRT        0xf8020000
#define CONFIG_SYS_PCIE3_IO_PHYS        0xff8020000ull

/* controller 4, Base address 203000 */
#define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
#define CONFIG_SYS_PCIE4_MEM_PHYS       0xc40000000ull
#define CONFIG_SYS_PCIE4_IO_PHYS        0xff8030000ull

#ifdef CONFIG_PCI
#if !defined(CONFIG_DM_PCI)
#define CONFIG_FSL_PCI_INIT     /* Use common FSL init code */
#define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
#define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
#define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000 /* 256M */
#define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
#define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE3_MEM_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
#define CONFIG_SYS_PCIE4_MEM_BUS        0xe0000000
#define CONFIG_SYS_PCIE4_MEM_SIZE       0x10000000      /* 256M */
#define CONFIG_SYS_PCIE4_IO_BUS         0x00000000
#define CONFIG_SYS_PCIE4_IO_SIZE        0x00010000      /* 64k */
#define CONFIG_PCI_INDIRECT_BRIDGE
#endif
#define CONFIG_PCI_SCAN_SHOW    /* show pci devices on startup */
#endif

/* Qman/Bman */
#ifndef CONFIG_NOBQFMAN
#define CONFIG_SYS_BMAN_NUM_PORTALS     18
#define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
#define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
#define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_BMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_BMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_BMAN_CENA_BASE       CONFIG_SYS_BMAN_MEM_BASE
#define CONFIG_SYS_BMAN_CENA_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_CINH_BASE       (CONFIG_SYS_BMAN_MEM_BASE + \
                                        CONFIG_SYS_BMAN_CENA_SIZE)
#define CONFIG_SYS_BMAN_CINH_SIZE       (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_BMAN_SWP_ISDR_REG    0xE08
#define CONFIG_SYS_QMAN_NUM_PORTALS     18
#define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
#define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
#define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
#define CONFIG_SYS_QMAN_SP_CENA_SIZE    0x4000
#define CONFIG_SYS_QMAN_SP_CINH_SIZE    0x1000
#define CONFIG_SYS_QMAN_CENA_BASE       CONFIG_SYS_QMAN_MEM_BASE
#define CONFIG_SYS_QMAN_CENA_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_CINH_BASE       (CONFIG_SYS_QMAN_MEM_BASE + \
                                        CONFIG_SYS_QMAN_CENA_SIZE)
#define CONFIG_SYS_QMAN_CINH_SIZE       (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
#define CONFIG_SYS_QMAN_SWP_ISDR_REG    0xE08

#define CONFIG_SYS_DPAA_FMAN
#define CONFIG_SYS_DPAA_PME
#define CONFIG_SYS_PMAN
#define CONFIG_SYS_DPAA_DCE
#define CONFIG_SYS_DPAA_RMAN            /* RMan */
#define CONFIG_SYS_INTERLAKEN

/* Default address of microcode for the Linux Fman driver */
#if defined(CONFIG_SPIFLASH)
/*
 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 * env, so we got 0x110000.
 */
#define CONFIG_SYS_FMAN_FW_ADDR         0x110000
#define CONFIG_CORTINA_FW_ADDR          0x120000

#elif defined(CONFIG_SDCARD)
/*
 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 * about 1MB (2048 blocks), Env is stored after the image, and the env size is
 * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080.
 */
#define CONFIG_SYS_FMAN_FW_ADDR         (512 * 0x820)
#define CONFIG_CORTINA_FW_ADDR          (512 * 0x8a0)

#elif defined(CONFIG_MTD_RAW_NAND)
#define CONFIG_SYS_FMAN_FW_ADDR         (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_CORTINA_FW_ADDR          (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
/*
 * Slave has no ucode locally, it can fetch this from remote. When implementing
 * in two corenet boards, slave's ucode could be stored in master's memory
 * space, the address can be mapped from slave TLB->slave LAW->
 * slave SRIO or PCIE outbound window->master inbound window->
 * master LAW->the ucode address in master's memory space.
 */
#define CONFIG_SYS_FMAN_FW_ADDR         0xFFE00000
#define CONFIG_CORTINA_FW_ADDR          0xFFE10000
#else
#define CONFIG_SYS_FMAN_FW_ADDR         0xEFF00000
#define CONFIG_CORTINA_FW_ADDR          0xEFE00000
#endif
#define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
#define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
#endif /* CONFIG_NOBQFMAN */

#ifdef CONFIG_SYS_DPAA_FMAN
#define CONFIG_CORTINA_FW_LENGTH        0x40000
#define RGMII_PHY1_ADDR         0x01  /* RealTek RTL8211E */
#define RGMII_PHY2_ADDR         0x02
#define CORTINA_PHY_ADDR1       0x0c  /* Cortina CS4315 */
#define CORTINA_PHY_ADDR2       0x0d
#define FM1_10GEC3_PHY_ADDR     0x00  /* Aquantia AQ1202 10G Base-T */
#define FM1_10GEC4_PHY_ADDR     0x01
#endif

#ifdef CONFIG_FMAN_ENET
#define CONFIG_ETHPRIME         "FM1@DTSEC3"
#endif

/*
 * SATA
 */
#ifdef CONFIG_FSL_SATA_V2
#define CONFIG_SYS_SATA_MAX_DEVICE      2
#define CONFIG_SATA1
#define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
#define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
#define CONFIG_SATA2
#define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
#define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
#define CONFIG_LBA48
#endif

/*
 * USB
 */
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_EHCI_FSL
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_HAS_FSL_DR_USB
#endif

/*
 * SDHC
 */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif

/*
 * Dynamic MTD Partition support with mtdparts
 */

/*
 * Environment
 */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LOAD_ADDR    0x2000000 /* default load address */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 64 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
#define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */

#ifdef CONFIG_CMD_KGDB
#define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
#endif

/*
 * Environment Configuration
 */
#define CONFIG_ROOTPATH  "/opt/nfsroot"
#define CONFIG_BOOTFILE  "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin"   /* U-Boot image on TFTP server */

/* default location for tftp and bootm */
#define CONFIG_LOADADDR         1000000
#define __USB_PHY_TYPE          utmi

#define CONFIG_EXTRA_ENV_SETTINGS                               \
        "hwconfig=fsl_ddr:"                                     \
        "ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","      \
        "bank_intlv=auto;"                                      \
        "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
        "netdev=eth0\0"                                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"             \
        "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"     \
        "tftpflash=tftpboot $loadaddr $uboot && "               \
        "protect off $ubootaddr +$filesize && "                 \
        "erase $ubootaddr +$filesize && "                       \
        "cp.b $loadaddr $ubootaddr $filesize && "               \
        "protect on $ubootaddr +$filesize && "                  \
        "cmp.b $loadaddr $ubootaddr $filesize\0"                \
        "consoledev=ttyS0\0"                                    \
        "ramdiskaddr=2000000\0"                                 \
        "ramdiskfile=t2080rdb/ramdisk.uboot\0"                  \
        "fdtaddr=1e00000\0"                                     \
        "fdtfile=t2080rdb/t2080rdb.dtb\0"                       \
        "bdev=sda3\0"

/*
 * For emulation this causes u-boot to jump to the start of the
 * proof point app code automatically
 */
#define CONFIG_PROOF_POINTS                             \
        "setenv bootargs root=/dev/$bdev rw "           \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "cpu 1 release 0x29000000 - - -;"               \
        "cpu 2 release 0x29000000 - - -;"               \
        "cpu 3 release 0x29000000 - - -;"               \
        "cpu 4 release 0x29000000 - - -;"               \
        "cpu 5 release 0x29000000 - - -;"               \
        "cpu 6 release 0x29000000 - - -;"               \
        "cpu 7 release 0x29000000 - - -;"               \
        "go 0x29000000"

#define CONFIG_HVBOOT                           \
        "setenv bootargs config-addr=0x60000000; "      \
        "bootm 0x01000000 - 0x00f00000"

#define CONFIG_ALU                              \
        "setenv bootargs root=/dev/$bdev rw "           \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "cpu 1 release 0x01000000 - - -;"               \
        "cpu 2 release 0x01000000 - - -;"               \
        "cpu 3 release 0x01000000 - - -;"               \
        "cpu 4 release 0x01000000 - - -;"               \
        "cpu 5 release 0x01000000 - - -;"               \
        "cpu 6 release 0x01000000 - - -;"               \
        "cpu 7 release 0x01000000 - - -;"               \
        "go 0x01000000"

#define CONFIG_LINUX                            \
        "setenv bootargs root=/dev/ram rw "             \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "setenv ramdiskaddr 0x02000000;"                \
        "setenv fdtaddr 0x00c00000;"                    \
        "setenv loadaddr 0x1000000;"                    \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_HDBOOT                                   \
        "setenv bootargs root=/dev/$bdev rw "           \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_NFSBOOTCOMMAND                   \
        "setenv bootargs root=/dev/nfs rw "     \
        "nfsroot=$serverip:$rootpath "          \
        "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $loadaddr $bootfile;"             \
        "tftp $fdtaddr $fdtfile;"               \
        "bootm $loadaddr - $fdtaddr"

#define CONFIG_RAMBOOTCOMMAND                           \
        "setenv bootargs root=/dev/ram rw "             \
        "console=$consoledev,$baudrate $othbootargs;"   \
        "tftp $ramdiskaddr $ramdiskfile;"               \
        "tftp $loadaddr $bootfile;"                     \
        "tftp $fdtaddr $fdtfile;"                       \
        "bootm $loadaddr $ramdiskaddr $fdtaddr"

#define CONFIG_BOOTCOMMAND              CONFIG_LINUX

#include <asm/fsl_secure_boot.h>

#endif  /* __T2080RDB_H */