1/* SPDX-License-Identifier: GPL-2.0+ */ 2/* 3 * bur_am335x_common.h 4 * 5 * common parts used by B&R AM335x based boards 6 * 7 * Copyright (C) 2016 Hannes Schmelzer <oe5hpm@oevsv.at> - 8 * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com 9 */ 10 11#ifndef __BUR_AM335X_COMMON_H__ 12#define __BUR_AM335X_COMMON_H__ 13/* ------------------------------------------------------------------------- */ 14 15/* legacy #defines for non DM bur-board */ 16#ifndef CONFIG_DM 17#define CONFIG_SYS_NS16550_SERIAL 18#define CONFIG_SYS_NS16550_REG_SIZE (-4) 19#define CONFIG_SYS_NS16550_CLK (48000000) 20#define CONFIG_SYS_NS16550_COM1 0x44e09000 21 22#define CONFIG_I2C 23#define CONFIG_SYS_I2C 24 25#endif /* CONFIG_DM */ 26 27#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ 28 29/* Timer information */ 30#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ 31#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ 32#define CONFIG_POWER_TPS65217 33 34#include <asm/arch/omap.h> 35 36/* 37 * SPL related defines. The Public RAM memory map the ROM defines the 38 * area between 0x402F0400 and 0x4030B800 as a download area and 39 * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also 40 * supports X-MODEM loading via UART, and we leverage this and then use 41 * Y-MODEM to load u-boot.img, when booted over UART. We must also include 42 * the scratch space that U-Boot uses in SRAM. 43 */ 44#define CONFIG_SPL_MAX_SIZE (SRAM_SCRATCH_SPACE_ADDR - \ 45 CONFIG_SPL_TEXT_BASE) 46 47/* 48 * Since SPL did pll and ddr initialization for us, 49 * we don't need to do it twice. 50 */ 51#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) 52#define CONFIG_SKIP_LOWLEVEL_INIT 53#endif /* !CONFIG_SPL_BUILD, ... */ 54/* 55 * Our DDR memory always starts at 0x80000000 and U-Boot shall have 56 * relocated itself to higher in memory by the time this value is used. 57 */ 58#define CONFIG_SYS_LOAD_ADDR 0x80000000 59/* 60 * ---------------------------------------------------------------------------- 61 * DDR information. We say (for simplicity) that we have 1 bank, 62 * always, even when we have more. We always start at 0x80000000, 63 * and we place the initial stack pointer in our SRAM. 64 */ 65#define CONFIG_SYS_SDRAM_BASE 0x80000000 66#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ 67 GENERATED_GBL_DATA_SIZE) 68 69/* 70 * Our platforms make use of SPL to initalize the hardware (primarily 71 * memory) enough for full U-Boot to be loaded. We also support Falcon 72 * Mode so that the Linux kernel can be booted directly from SPL 73 * instead, if desired. We make use of the general SPL framework found 74 * under common/spl/. Given our generally common memory map, we set a 75 * number of related defaults and sizes here. 76 */ 77/* 78 * Place the image at the start of the ROM defined image space. 79 * We limit our size to the ROM-defined downloaded image area, and use the 80 * rest of the space for stack. We load U-Boot itself into memory at 81 * 0x80800000 for legacy reasons (to not conflict with older SPLs). We 82 * have our BSS be placed 1MiB after this, to allow for the default 83 * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. 84 * We have the SPL malloc pool at the end of the BSS area. 85 * 86 * ---------------------------------------------------------------------------- 87 */ 88#define CONFIG_SPL_BSS_START_ADDR 0x80A00000 89#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ 90#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ 91 CONFIG_SPL_BSS_MAX_SIZE) 92#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN 93 94/* General parts of the framework, required. */ 95 96#endif /* ! __BUR_AM335X_COMMON_H__ */ 97