LXR uboot/include/configs/vme8349.h

   1/* SPDX-License-Identifier: GPL-2.0+ */
   2/*
   3 * esd vme8349 U-Boot configuration file
   4 * Copyright (c) 2008, 2009 esd gmbh Hannover Germany
   5 *
   6 * (C) Copyright 2006-2010
   7 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   8 *
   9 * reinhard.arlt@esd-electronics.de
  10 * Based on the MPC8349EMDS config.
  11 */
  12
  13/*
  14 * vme8349 board configuration file.
  15 */
  16
  17#ifndef __CONFIG_H
  18#define __CONFIG_H
  19
  20/*
  21 * High Level Configuration Options
  22 */
  23#define CONFIG_E300             1       /* E300 Family */
  24
  25/* Don't enable PCI2 on vme834x - it doesn't exist physically. */
  26#undef CONFIG_MPC83XX_PCI2              /* support for 2nd PCI controller */
  27
  28#undef CONFIG_SYS_DRAM_TEST                     /* memory test, takes time */
  29
  30/*
  31 * DDR Setup
  32 */
  33#define CONFIG_DDR_ECC                  /* only for ECC DDR module */
  34#define CONFIG_DDR_ECC_CMD              /* use DDR ECC user commands */
  35#define CONFIG_SPD_EEPROM
  36#define SPD_EEPROM_ADDRESS              0x54
  37#define CONFIG_SYS_READ_SPD             vme8349_read_spd
  38#define CONFIG_SYS_83XX_DDR_USES_CS0    /* esd; Fsl board uses CS2/CS3 */
  39
  40/*
  41 * 32-bit data path mode.
  42 *
  43 * Please note that using this mode for devices with the real density of 64-bit
  44 * effectively reduces the amount of available memory due to the effect of
  45 * wrapping around while translating address to row/columns, for example in the
  46 * 256MB module the upper 128MB get aliased with contents of the lower
  47 * 128MB); normally this define should be used for devices with real 32-bit
  48 * data path.
  49 */
  50#undef CONFIG_DDR_32BIT
  51
  52#define CONFIG_SYS_SDRAM_BASE           0x00000000      /* DDR is sys memory*/
  53#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN \
  54                                        | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
  55#define CONFIG_DDR_2T_TIMING
  56#define CONFIG_SYS_DDRCDR               (DDRCDR_DHC_EN \
  57                                        | DDRCDR_ODT \
  58                                        | DDRCDR_Q_DRN)
  59                                        /* 0x80080001 */
  60
  61/*
  62 * FLASH on the Local Bus
  63 */
  64#define CONFIG_SYS_FLASH_BASE           0xf8000000      /* start of FLASH   */
  65#define CONFIG_SYS_FLASH_SIZE           128             /* flash size in MB */
  66
  67
  68#define CONFIG_SYS_WINDOW1_BASE         0xf0000000
  69
  70
  71#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
  72#define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device*/
  73
  74#undef CONFIG_SYS_FLASH_CHECKSUM
  75#define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase TO (ms) */
  76#define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write TO (ms) */
  77
  78#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE    /* start of monitor */
  79
  80#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
  81#define CONFIG_SYS_RAMBOOT
  82#else
  83#undef CONFIG_SYS_RAMBOOT
  84#endif
  85
  86#define CONFIG_SYS_INIT_RAM_LOCK        1
  87#define CONFIG_SYS_INIT_RAM_ADDR        0xF7000000      /* Initial RAM addr */
  88#define CONFIG_SYS_INIT_RAM_SIZE                0x1000          /* size */
  89
  90#define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
  91                                         GENERATED_GBL_DATA_SIZE)
  92#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
  93
  94#define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB */
  95#define CONFIG_SYS_MALLOC_LEN           (256 * 1024)    /* Malloc size */
  96
  97#undef CONFIG_SYS_LB_SDRAM      /* if board has SDRAM on local bus */
  98
  99/*
 100 * Serial Port
 101 */
 102#define CONFIG_SYS_NS16550_SERIAL
 103#define CONFIG_SYS_NS16550_REG_SIZE     1
 104#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 105
 106#define CONFIG_SYS_BAUDRATE_TABLE  \
 107                {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 108
 109#define CONFIG_SYS_NS16550_COM1         (CONFIG_SYS_IMMR + 0x4500)
 110#define CONFIG_SYS_NS16550_COM2         (CONFIG_SYS_IMMR + 0x4600)
 111
 112/* I2C */
 113#define CONFIG_SYS_I2C
 114#define CONFIG_SYS_I2C_FSL
 115#define CONFIG_SYS_FSL_I2C_SPEED        400000
 116#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 117#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
 118#define CONFIG_SYS_FSL_I2C2_SPEED       400000
 119#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 120#define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100
 121#define CONFIG_SYS_I2C_NOPROBES         { {0, 0x69} }
 122/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */
 123
 124#define CONFIG_SYS_I2C_8574_ADDR2       0x20    /* I2C1, PCF8574 */
 125
 126/* TSEC */
 127#define CONFIG_SYS_TSEC1_OFFSET 0x24000
 128#define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET)
 129#define CONFIG_SYS_TSEC2_OFFSET 0x25000
 130#define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET)
 131
 132/*
 133 * General PCI
 134 * Addresses are mapped 1-1.
 135 */
 136#define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 137#define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 138#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 139#define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 140#define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 141#define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000      /* 256M */
 142#define CONFIG_SYS_PCI1_IO_BASE         0x00000000
 143#define CONFIG_SYS_PCI1_IO_PHYS         0xE2000000
 144#define CONFIG_SYS_PCI1_IO_SIZE         0x00100000      /* 1M */
 145
 146#define CONFIG_SYS_PCI2_MEM_BASE        0xA0000000
 147#define CONFIG_SYS_PCI2_MEM_PHYS        CONFIG_SYS_PCI2_MEM_BASE
 148#define CONFIG_SYS_PCI2_MEM_SIZE        0x10000000      /* 256M */
 149#define CONFIG_SYS_PCI2_MMIO_BASE       0xB0000000
 150#define CONFIG_SYS_PCI2_MMIO_PHYS       CONFIG_SYS_PCI2_MMIO_BASE
 151#define CONFIG_SYS_PCI2_MMIO_SIZE       0x10000000      /* 256M */
 152#define CONFIG_SYS_PCI2_IO_BASE         0x00000000
 153#define CONFIG_SYS_PCI2_IO_PHYS         0xE2100000
 154#define CONFIG_SYS_PCI2_IO_SIZE         0x00100000      /* 1M */
 155
 156#if defined(CONFIG_PCI)
 157
 158
 159#if !defined(CONFIG_PCI_PNP)
 160        #define PCI_ENET0_IOADDR        0xFIXME
 161        #define PCI_ENET0_MEMADDR       0xFIXME
 162        #define PCI_IDSEL_NUMBER        0xFIXME
 163#endif
 164
 165#define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 166#define CONFIG_SYS_PCI_SUBSYS_VENDORID  0x1957  /* Freescale */
 167
 168#endif  /* CONFIG_PCI */
 169
 170/*
 171 * TSEC configuration
 172 */
 173
 174#if defined(CONFIG_TSEC_ENET)
 175
 176#define CONFIG_GMII                     /* MII PHY management */
 177#define CONFIG_TSEC1
 178#define CONFIG_TSEC1_NAME       "TSEC0"
 179#define CONFIG_TSEC2
 180#define CONFIG_TSEC2_NAME       "TSEC1"
 181#define CONFIG_PHY_M88E1111
 182#define TSEC1_PHY_ADDR          0x08
 183#define TSEC2_PHY_ADDR          0x10
 184#define TSEC1_PHYIDX            0
 185#define TSEC2_PHYIDX            0
 186#define TSEC1_FLAGS             TSEC_GIGABIT
 187#define TSEC2_FLAGS             TSEC_GIGABIT
 188
 189/* Options are: TSEC[0-1] */
 190#define CONFIG_ETHPRIME         "TSEC0"
 191
 192#endif  /* CONFIG_TSEC_ENET */
 193
 194/*
 195 * Environment
 196 */
 197#ifndef CONFIG_SYS_RAMBOOT
 198/* Address and size of Redundant Environment Sector     */
 199#endif
 200
 201#define CONFIG_LOADS_ECHO               /* echo on for serial download */
 202#define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 203
 204/*
 205 * BOOTP options
 206 */
 207#define CONFIG_BOOTP_BOOTFILESIZE
 208
 209#define CONFIG_SYS_RTC_BUS_NUM  0x01
 210#define CONFIG_SYS_I2C_RTC_ADDR 0x32
 211
 212/* Pass Ethernet MAC to VxWorks */
 213#define CONFIG_SYS_VXWORKS_MAC_PTR      0x000043f0
 214
 215#undef CONFIG_WATCHDOG                  /* watchdog disabled */
 216
 217/*
 218 * Miscellaneous configurable options
 219 */
 220#define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 221
 222/*
 223 * For booting Linux, the board info and command line data
 224 * have to be in the first 256 MB of memory, since this is
 225 * the maximum mapped by the Linux kernel during initialization.
 226 */
 227#define CONFIG_SYS_BOOTMAPSZ    (256 << 20)     /* Init Memory map for Linux*/
 228
 229#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 230
 231/* System IO Config */
 232#define CONFIG_SYS_SICRH 0
 233#define CONFIG_SYS_SICRL SICRL_LDP_A
 234
 235#define CONFIG_SYS_GPIO1_PRELIM
 236#define CONFIG_SYS_GPIO1_DIR    0x00100000
 237#define CONFIG_SYS_GPIO1_DAT    0x00100000
 238
 239#define CONFIG_SYS_GPIO2_PRELIM
 240#define CONFIG_SYS_GPIO2_DIR    0x78900000
 241#define CONFIG_SYS_GPIO2_DAT    0x70100000
 242
 243#ifdef CONFIG_PCI
 244#define CONFIG_PCI_INDIRECT_BRIDGE
 245#endif
 246
 247#if defined(CONFIG_CMD_KGDB)
 248#define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 249#endif
 250
 251/*
 252 * Environment Configuration
 253 */
 254
 255#if defined(CONFIG_TSEC_ENET)
 256#define CONFIG_HAS_ETH0
 257#define CONFIG_HAS_ETH1
 258#endif
 259
 260#define CONFIG_HOSTNAME         "VME8349"
 261#define CONFIG_ROOTPATH         "/tftpboot/rootfs"
 262#define CONFIG_BOOTFILE         "uImage"
 263
 264#define CONFIG_LOADADDR         800000  /* def location for tftp and bootm */
 265
 266#define CONFIG_EXTRA_ENV_SETTINGS                                       \
 267        "netdev=eth0\0"                                                 \
 268        "hostname=vme8349\0"                                            \
 269        "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 270                "nfsroot=${serverip}:${rootpath}\0"                     \
 271        "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 272        "addip=setenv bootargs ${bootargs} "                            \
 273                "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 274                ":${hostname}:${netdev}:off panic=1\0"                  \
 275        "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 276        "flash_nfs=run nfsargs addip addtty;"                           \
 277                "bootm ${kernel_addr}\0"                                \
 278        "flash_self=run ramargs addip addtty;"                          \
 279                "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 280        "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
 281                "bootm\0"                                               \
 282        "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0"              \
 283        "update=protect off fff00000 fff3ffff; "                        \
 284                "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \
 285        "upd=run load update\0"                                         \
 286        "fdtaddr=780000\0"                                              \
 287        "fdtfile=vme8349.dtb\0"                                         \
 288        ""
 289
 290#define CONFIG_NFSBOOTCOMMAND                                           \
 291        "setenv bootargs root=/dev/nfs rw "                             \
 292                "nfsroot=$serverip:$rootpath "                          \
 293                "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"   \
 294                                                        "$netdev:off "  \
 295                "console=$consoledev,$baudrate $othbootargs;"           \
 296        "tftp $loadaddr $bootfile;"                                     \
 297        "tftp $fdtaddr $fdtfile;"                                       \
 298        "bootm $loadaddr - $fdtaddr"
 299
 300#define CONFIG_RAMBOOTCOMMAND                                           \
 301        "setenv bootargs root=/dev/ram rw "                             \
 302                "console=$consoledev,$baudrate $othbootargs;"           \
 303        "tftp $ramdiskaddr $ramdiskfile;"                               \
 304        "tftp $loadaddr $bootfile;"                                     \
 305        "tftp $fdtaddr $fdtfile;"                                       \
 306        "bootm $loadaddr $ramdiskaddr $fdtaddr"
 307
 308#define CONFIG_BOOTCOMMAND      "run flash_self"
 309
 310#ifndef __ASSEMBLY__
 311int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen,
 312                     unsigned char *buffer, int len);
 313#endif
 314
 315#endif  /* __CONFIG_H */
 316