// SPDX-License-Identifier: GPL-2.0+
/*
 * Copyright (C) 2014 Samsung Electronics
 * Przemyslaw Marczak <p.marczak@samsung.com>
 */

#include <common.h>
#include <log.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/power.h>
#include <asm/arch/clock.h>
#include <asm/arch/gpio.h>
#include <asm/global_data.h>
#include <asm/gpio.h>
#include <asm/arch/cpu.h>
#include <dm.h>
#include <env.h>
#include <power/pmic.h>
#include <power/regulator.h>
#include <power/max77686_pmic.h>
#include <errno.h>
#include <mmc.h>
#include <usb.h>
#include <usb/dwc2_udc.h>
#include <samsung/misc.h>
#include "setup.h"

DECLARE_GLOBAL_DATA_PTR;

#ifdef CONFIG_BOARD_TYPES
/* Odroid board types */
enum {
        ODROID_TYPE_U3,
        ODROID_TYPE_X2,
        ODROID_TYPES,
};

void set_board_type(void)
{
        /* Set GPA1 pin 1 to HI - enable XCL205 output */
        writel(XCL205_EN_GPIO_CON_CFG, XCL205_EN_GPIO_CON);
        writel(XCL205_EN_GPIO_DAT_CFG, XCL205_EN_GPIO_CON + 0x4);
        writel(XCL205_EN_GPIO_PUD_CFG, XCL205_EN_GPIO_CON + 0x8);
        writel(XCL205_EN_GPIO_DRV_CFG, XCL205_EN_GPIO_CON + 0xc);

        /* Set GPC1 pin 2 to IN - check XCL205 output state */
        writel(XCL205_STATE_GPIO_CON_CFG, XCL205_STATE_GPIO_CON);
        writel(XCL205_STATE_GPIO_PUD_CFG, XCL205_STATE_GPIO_CON + 0x8);

        /* XCL205 - needs some latch time */
        sdelay(200000);

        /* Check GPC1 pin2 - LED supplied by XCL205 - X2 only */
        if (readl(XCL205_STATE_GPIO_DAT) & (1 << XCL205_STATE_GPIO_PIN))
                gd->board_type = ODROID_TYPE_X2;
        else
                gd->board_type = ODROID_TYPE_U3;
}

void set_board_revision(void)
{
        /*
         * Revision already set by set_board_type() because it can be
         * executed early.
         */
}

const char *get_board_type(void)
{
        const char *board_type[] = {"u3", "x2"};

        return board_type[gd->board_type];
}
#endif

#ifdef CONFIG_SET_DFU_ALT_INFO
char *get_dfu_alt_system(char *interface, char *devstr)
{
        return env_get("dfu_alt_system");
}

char *get_dfu_alt_boot(char *interface, char *devstr)
{
        struct mmc *mmc;
        char *alt_boot;
        int dev_num;

        dev_num = dectoul(devstr, NULL);

        mmc = find_mmc_device(dev_num);
        if (!mmc)
                return NULL;

        if (mmc_init(mmc))
                return NULL;

        alt_boot = IS_SD(mmc) ? CONFIG_DFU_ALT_BOOT_SD :
                                CONFIG_DFU_ALT_BOOT_EMMC;

        return alt_boot;
}
#endif

static void board_clock_init(void)
{
        unsigned int set, clr, clr_src_cpu, clr_pll_con0, clr_src_dmc;
        struct exynos4x12_clock *clk = (struct exynos4x12_clock *)
                                                samsung_get_base_clock();

        /*
         * CMU_CPU clocks src to MPLL
         * Bit values:                 0  ; 1
         * MUX_APLL_SEL:        FIN_PLL   ; FOUT_APLL
         * MUX_CORE_SEL:        MOUT_APLL ; SCLK_MPLL
         * MUX_HPM_SEL:         MOUT_APLL ; SCLK_MPLL_USER_C
         * MUX_MPLL_USER_SEL_C: FIN_PLL   ; SCLK_MPLL
        */
        clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1) |
                      MUX_HPM_SEL(1) | MUX_MPLL_USER_SEL_C(1);
        set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1) | MUX_HPM_SEL(1) |
              MUX_MPLL_USER_SEL_C(1);

        clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);

        /* Wait for mux change */
        while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
                continue;

        /* Set APLL to 1000MHz */
        clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1);
        set = SDIV(0) | PDIV(3) | MDIV(125) | FSEL(1);

        clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);

        /* Wait for PLL to be locked */
        while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
                continue;

        /* Set CMU_CPU clocks src to APLL */
        set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0) | MUX_HPM_SEL(0) |
              MUX_MPLL_USER_SEL_C(1);
        clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);

        /* Wait for mux change */
        while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
                continue;

        set = CORE_RATIO(0) | COREM0_RATIO(2) | COREM1_RATIO(5) |
              PERIPH_RATIO(0) | ATB_RATIO(4) | PCLK_DBG_RATIO(1) |
              APLL_RATIO(0) | CORE2_RATIO(0);
        /*
         * Set dividers for MOUTcore = 1000 MHz
         * coreout =      MOUT / (ratio + 1) = 1000 MHz (0)
         * corem0 =     armclk / (ratio + 1) = 333 MHz (2)
         * corem1 =     armclk / (ratio + 1) = 166 MHz (5)
         * periph =     armclk / (ratio + 1) = 1000 MHz (0)
         * atbout =       MOUT / (ratio + 1) = 200 MHz (4)
         * pclkdbgout = atbout / (ratio + 1) = 100 MHz (1)
         * sclkapll = MOUTapll / (ratio + 1) = 1000 MHz (0)
         * core2out = core_out / (ratio + 1) = 1000 MHz (0) (armclk)
        */
        clr = CORE_RATIO(7) | COREM0_RATIO(7) | COREM1_RATIO(7) |
              PERIPH_RATIO(7) | ATB_RATIO(7) | PCLK_DBG_RATIO(7) |
              APLL_RATIO(7) | CORE2_RATIO(7);

        clrsetbits_le32(&clk->div_cpu0, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
                continue;

        /*
         * For MOUThpm = 1000 MHz (MOUTapll)
         * doutcopy = MOUThpm / (ratio + 1) = 200 (4)
         * sclkhpm = doutcopy / (ratio + 1) = 200 (4)
         * cores_out = armclk / (ratio + 1) = 200 (4)
         */
        clr = COPY_RATIO(7) | HPM_RATIO(7) | CORES_RATIO(7);
        set = COPY_RATIO(4) | HPM_RATIO(4) | CORES_RATIO(4);

        clrsetbits_le32(&clk->div_cpu1, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_cpu1) & DIV_STAT_CPU1_CHANGING)
                continue;

        /*
         * Set CMU_DMC clocks src to APLL
         * Bit values:             0  ; 1
         * MUX_C2C_SEL:      SCLKMPLL ; SCLKAPLL
         * MUX_DMC_BUS_SEL:  SCLKMPLL ; SCLKAPLL
         * MUX_DPHY_SEL:     SCLKMPLL ; SCLKAPLL
         * MUX_MPLL_SEL:     FINPLL   ; MOUT_MPLL_FOUT
         * MUX_PWI_SEL:      0110 (MPLL); 0111 (EPLL); 1000 (VPLL); 0(XXTI)
         * MUX_G2D_ACP0_SEL: SCLKMPLL ; SCLKAPLL
         * MUX_G2D_ACP1_SEL: SCLKEPLL ; SCLKVPLL
         * MUX_G2D_ACP_SEL:  OUT_ACP0 ; OUT_ACP1
        */
        clr_src_dmc = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) |
                      MUX_DPHY_SEL(1) | MUX_MPLL_SEL(1) |
                      MUX_PWI_SEL(15) | MUX_G2D_ACP0_SEL(1) |
                      MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
        set = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | MUX_DPHY_SEL(1) |
              MUX_MPLL_SEL(0) | MUX_PWI_SEL(0) | MUX_G2D_ACP0_SEL(1) |
              MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);

        clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);

        /* Wait for mux change */
        while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
                continue;

        /* Set MPLL to 800MHz */
        set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1);

        clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);

        /* Wait for PLL to be locked */
        while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
                continue;

        /* Switch back CMU_DMC mux */
        set = MUX_C2C_SEL(0) | MUX_DMC_BUS_SEL(0) | MUX_DPHY_SEL(0) |
              MUX_MPLL_SEL(1) | MUX_PWI_SEL(8) | MUX_G2D_ACP0_SEL(0) |
              MUX_G2D_ACP1_SEL(0) | MUX_G2D_ACP_SEL(0);

        clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);

        /* Wait for mux change */
        while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
                continue;

        /* CLK_DIV_DMC0 */
        clr = ACP_RATIO(7) | ACP_PCLK_RATIO(7) | DPHY_RATIO(7) |
              DMC_RATIO(7) | DMCD_RATIO(7) | DMCP_RATIO(7);
        /*
         * For:
         * MOUTdmc = 800 MHz
         * MOUTdphy = 800 MHz
         *
         * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3)
         * pclk_acp = aclk_acp / (ratio + 1) = 100 (1)
         * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1)
         * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1)
         * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1)
         * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1)
         */
        set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) |
              DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1);

        clrsetbits_le32(&clk->div_dmc0, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_dmc0) & DIV_STAT_DMC0_CHANGING)
                continue;

        /* CLK_DIV_DMC1 */
        clr = G2D_ACP_RATIO(15) | C2C_RATIO(7) | PWI_RATIO(15) |
              C2C_ACLK_RATIO(7) | DVSEM_RATIO(127) | DPM_RATIO(127);
        /*
         * For:
         * MOUTg2d = 800 MHz
         * MOUTc2c = 800 Mhz
         * MOUTpwi = 108 MHz
         *
         * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 200 (3)
         * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1)
         * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1)
         * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5)
         */
        set = G2D_ACP_RATIO(3) | C2C_RATIO(1) | PWI_RATIO(5) |
              C2C_ACLK_RATIO(1) | DVSEM_RATIO(1) | DPM_RATIO(1);

        clrsetbits_le32(&clk->div_dmc1, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_dmc1) & DIV_STAT_DMC1_CHANGING)
                continue;

        /* CLK_SRC_PERIL0 */
        clr = UART0_SEL(15) | UART1_SEL(15) | UART2_SEL(15) |
              UART3_SEL(15) | UART4_SEL(15);
        /*
         * Set CLK_SRC_PERIL0 clocks src to MPLL
         * src values: 0(XXTI); 1(XusbXTI); 2(SCLK_HDMI24M); 3(SCLK_USBPHY0);
         *             5(SCLK_HDMIPHY); 6(SCLK_MPLL_USER_T); 7(SCLK_EPLL);
         *             8(SCLK_VPLL)
         *
         * Set all to SCLK_MPLL_USER_T
         */
        set = UART0_SEL(6) | UART1_SEL(6) | UART2_SEL(6) | UART3_SEL(6) |
              UART4_SEL(6);

        clrsetbits_le32(&clk->src_peril0, clr, set);

        /* CLK_DIV_PERIL0 */
        clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) |
              UART3_RATIO(15) | UART4_RATIO(15);
        /*
         * For MOUTuart0-4: 800MHz
         *
         * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7)
        */
        set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) |
              UART3_RATIO(7) | UART4_RATIO(7);

        clrsetbits_le32(&clk->div_peril0, clr, set);

        while (readl(&clk->div_stat_peril0) & DIV_STAT_PERIL0_CHANGING)
                continue;

        /* CLK_DIV_FSYS1 */
        clr = MMC0_RATIO(15) | MMC0_PRE_RATIO(255) | MMC1_RATIO(15) |
              MMC1_PRE_RATIO(255);
        /*
         * For MOUTmmc0-3 = 800 MHz (MPLL)
         *
         * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7)
         * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1)
         * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7)
         * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1)
        */
        set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) |
              MMC1_PRE_RATIO(1);

        clrsetbits_le32(&clk->div_fsys1, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING)
                continue;

        /* CLK_DIV_FSYS2 */
        clr = MMC2_RATIO(15) | MMC2_PRE_RATIO(255) | MMC3_RATIO(15) |
              MMC3_PRE_RATIO(255);
        /*
         * For MOUTmmc0-3 = 800 MHz (MPLL)
         *
         * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7)
         * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1)
         * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7)
         * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1)
        */
        set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) |
              MMC3_PRE_RATIO(1);

        clrsetbits_le32(&clk->div_fsys2, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_fsys2) & DIV_STAT_FSYS2_CHANGING)
                continue;

        /* CLK_DIV_FSYS3 */
        clr = MMC4_RATIO(15) | MMC4_PRE_RATIO(255);
        /*
         * For MOUTmmc4 = 800 MHz (MPLL)
         *
         * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7)
         * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0)
        */
        set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0);

        clrsetbits_le32(&clk->div_fsys3, clr, set);

        /* Wait for divider ready status */
        while (readl(&clk->div_stat_fsys3) & DIV_STAT_FSYS3_CHANGING)
                continue;

        return;
}

static void board_gpio_init(void)
{
        /* eMMC Reset Pin */
        gpio_request(EXYNOS4X12_GPIO_K12, "eMMC Reset");

        gpio_cfg_pin(EXYNOS4X12_GPIO_K12, S5P_GPIO_FUNC(0x1));
        gpio_set_pull(EXYNOS4X12_GPIO_K12, S5P_GPIO_PULL_NONE);
        gpio_set_drv(EXYNOS4X12_GPIO_K12, S5P_GPIO_DRV_4X);

        /* Enable FAN (Odroid U3) */
        gpio_request(EXYNOS4X12_GPIO_D00, "FAN Control");

        gpio_set_pull(EXYNOS4X12_GPIO_D00, S5P_GPIO_PULL_UP);
        gpio_set_drv(EXYNOS4X12_GPIO_D00, S5P_GPIO_DRV_4X);
        gpio_direction_output(EXYNOS4X12_GPIO_D00, 1);

        /* OTG Vbus output (Odroid U3+) */
        gpio_request(EXYNOS4X12_GPIO_L20, "OTG Vbus");

        gpio_set_pull(EXYNOS4X12_GPIO_L20, S5P_GPIO_PULL_NONE);
        gpio_set_drv(EXYNOS4X12_GPIO_L20, S5P_GPIO_DRV_4X);
        gpio_direction_output(EXYNOS4X12_GPIO_L20, 0);

        /* OTG INT (Odroid U3+) */
        gpio_request(EXYNOS4X12_GPIO_X31, "OTG INT");

        gpio_set_pull(EXYNOS4X12_GPIO_X31, S5P_GPIO_PULL_UP);
        gpio_set_drv(EXYNOS4X12_GPIO_X31, S5P_GPIO_DRV_4X);
        gpio_direction_input(EXYNOS4X12_GPIO_X31);

        /* Blue LED (Odroid X2/U2/U3) */
        gpio_request(EXYNOS4X12_GPIO_C10, "Blue LED");

        gpio_direction_output(EXYNOS4X12_GPIO_C10, 0);

#ifdef CONFIG_CMD_USB
        /* USB3503A Reference frequency */
        gpio_request(EXYNOS4X12_GPIO_X30, "USB3503A RefFreq");

        /* USB3503A Connect */
        gpio_request(EXYNOS4X12_GPIO_X34, "USB3503A Connect");

        /* USB3503A Reset */
        gpio_request(EXYNOS4X12_GPIO_X35, "USB3503A Reset");
#endif
}

int exynos_early_init_f(void)
{
        board_clock_init();

        return 0;
}

int exynos_init(void)
{
        board_gpio_init();

        return 0;
}

int exynos_power_init(void)
{
        const char *mmc_regulators[] = {
                "VDDQ_EMMC_1.8V",
                "VDDQ_EMMC_2.8V",
                "TFLASH_2.8V",
                NULL,
        };

        if (regulator_list_autoset(mmc_regulators, NULL, true))
                pr_err("Unable to init all mmc regulators\n");

        return 0;
}

#ifdef CONFIG_USB_GADGET
static int s5pc210_phy_control(int on)
{
        struct udevice *dev;
        int ret;

        ret = regulator_get_by_platname("VDD_UOTG_3.0V", &dev);
        if (ret) {
                pr_err("Regulator get error: %d\n", ret);
                return ret;
        }

        if (on)
                return regulator_set_mode(dev, OPMODE_ON);
        else
                return regulator_set_mode(dev, OPMODE_LPM);
}

struct dwc2_plat_otg_data s5pc210_otg_data = {
        .phy_control    = s5pc210_phy_control,
        .regs_phy       = EXYNOS4X12_USBPHY_BASE,
        .regs_otg       = EXYNOS4X12_USBOTG_BASE,
        .usb_phy_ctrl   = EXYNOS4X12_USBPHY_CONTROL,
        .usb_flags      = PHY0_SLEEP,
};
#endif

#if defined(CONFIG_USB_GADGET) || defined(CONFIG_CMD_USB)

static void set_usb3503_ref_clk(void)
{
#ifdef CONFIG_BOARD_TYPES
        /*
         * gpx3-0 chooses primary (low) or secondary (high) reference clock
         * frequencies table.  The choice of clock is done through hard-wired
         * REF_SEL pins.
         * The Odroid Us have reference clock at 24 MHz (00 entry from secondary
         * table) and Odroid Xs have it at 26 MHz (01 entry from primary table).
         */
        if (gd->board_type == ODROID_TYPE_U3)
                gpio_direction_output(EXYNOS4X12_GPIO_X30, 0);
        else
                gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
#else
        /* Choose Odroid Xs frequency without board types */
        gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
#endif /* CONFIG_BOARD_TYPES */
}

int board_usb_init(int index, enum usb_init_type init)
{
#ifdef CONFIG_CMD_USB
        struct udevice *dev;
        int ret;

        set_usb3503_ref_clk();

        /* Disconnect, Reset, Connect */
        gpio_direction_output(EXYNOS4X12_GPIO_X34, 0);
        gpio_direction_output(EXYNOS4X12_GPIO_X35, 0);
        gpio_direction_output(EXYNOS4X12_GPIO_X35, 1);
        gpio_direction_output(EXYNOS4X12_GPIO_X34, 1);

        /* Power off and on BUCK8 for LAN9730 */
        debug("LAN9730 - Turning power buck 8 OFF and ON.\n");

        ret = regulator_get_by_platname("VCC_P3V3_2.85V", &dev);
        if (ret) {
                pr_err("Regulator get error: %d\n", ret);
                return ret;
        }

        ret = regulator_set_enable(dev, true);
        if (ret) {
                pr_err("Regulator %s enable setting error: %d\n", dev->name, ret);
                return ret;
        }

        ret = regulator_set_value(dev, 750000);
        if (ret) {
                pr_err("Regulator %s value setting error: %d\n", dev->name, ret);
                return ret;
        }

        ret = regulator_set_value(dev, 3300000);
        if (ret) {
                pr_err("Regulator %s value setting error: %d\n", dev->name, ret);
                return ret;
        }
#endif
        debug("USB_udc_probe\n");
        return dwc2_udc_probe(&s5pc210_otg_data);
}
#endif