// SPDX-License-Identifier: GPL-2.0+
/**************************************************************************
Intel Pro 1000 for ppcboot/das-u-boot
Drivers are port from Intel's Linux driver e1000-4.3.15
and from Etherboot pro 1000 driver by mrakes at vivato dot net
tested on both gig copper and gig fiber boards
***************************************************************************/
/*******************************************************************************


  Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved.


  Contact Information:
  Linux NICS <linux.nics@intel.com>
  Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497

*******************************************************************************/
/*
 *  Copyright (C) Archway Digital Solutions.
 *
 *  written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org>
 *  2/9/2002
 *
 *  Copyright (C) Linux Networx.
 *  Massive upgrade to work with the new intel gigabit NICs.
 *  <ebiederman at lnxi dot com>
 *
 *  Copyright 2011 Freescale Semiconductor, Inc.
 */

#include <common.h>
#include <command.h>
#include <cpu_func.h>
#include <dm.h>
#include <errno.h>
#include <log.h>
#include <malloc.h>
#include <memalign.h>
#include <net.h>
#include <pci.h>
#include <linux/delay.h>
#include "e1000.h"
#include <asm/cache.h>

#define TOUT_LOOP   100000

#define E1000_DEFAULT_PCI_PBA   0x00000030
#define E1000_DEFAULT_PCIE_PBA  0x000a0026

/* NIC specific static variables go here */

/* Intel i210 needs the DMA descriptor rings aligned to 128b */
#define E1000_BUFFER_ALIGN      128

/*
 * TODO(sjg@chromium.org): Even with driver model we share these buffers.
 * Concurrent receiving on multiple active Ethernet devices will not work.
 * Normally U-Boot does not support this anyway. To fix it in this driver,
 * move these buffers and the tx/rx pointers to struct e1000_hw.
 */
DEFINE_ALIGN_BUFFER(struct e1000_tx_desc, tx_base, 16, E1000_BUFFER_ALIGN);
DEFINE_ALIGN_BUFFER(struct e1000_rx_desc, rx_base, 16, E1000_BUFFER_ALIGN);
DEFINE_ALIGN_BUFFER(unsigned char, packet, 4096, E1000_BUFFER_ALIGN);

static int tx_tail;
static int rx_tail, rx_last;
#ifdef CONFIG_DM_ETH
static int num_cards;   /* Number of E1000 devices seen so far */
#endif

static struct pci_device_id e1000_supported[] = {
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545GM_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF) },
        /* E1000 PCIe card */
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82574L) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_COPPER) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS) },
        { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_1000BASEKX) },

        {}
};

/* Function forward declarations */
static int e1000_setup_link(struct e1000_hw *hw);
static int e1000_setup_fiber_link(struct e1000_hw *hw);
static int e1000_setup_copper_link(struct e1000_hw *hw);
static int e1000_phy_setup_autoneg(struct e1000_hw *hw);
static void e1000_config_collision_dist(struct e1000_hw *hw);
static int e1000_config_mac_to_phy(struct e1000_hw *hw);
static int e1000_config_fc_after_link_up(struct e1000_hw *hw);
static int e1000_check_for_link(struct e1000_hw *hw);
static int e1000_wait_autoneg(struct e1000_hw *hw);
static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed,
                                       uint16_t * duplex);
static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
                              uint16_t * phy_data);
static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr,
                               uint16_t phy_data);
static int32_t e1000_phy_hw_reset(struct e1000_hw *hw);
static int e1000_phy_reset(struct e1000_hw *hw);
static int e1000_detect_gig_phy(struct e1000_hw *hw);
static void e1000_set_media_type(struct e1000_hw *hw);

static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask);
static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask);
static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw);

#ifndef CONFIG_E1000_NO_NVM
static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw);
static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw);
static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
                uint16_t words,
                uint16_t *data);
/******************************************************************************
 * Raises the EEPROM's clock input.
 *
 * hw - Struct containing variables accessed by shared code
 * eecd - EECD's current value
 *****************************************************************************/
void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
{
        /* Raise the clock input to the EEPROM (by setting the SK bit), and then
         * wait 50 microseconds.
         */
        *eecd = *eecd | E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, *eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);
}

/******************************************************************************
 * Lowers the EEPROM's clock input.
 *
 * hw - Struct containing variables accessed by shared code
 * eecd - EECD's current value
 *****************************************************************************/
void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd)
{
        /* Lower the clock input to the EEPROM (by clearing the SK bit), and then
         * wait 50 microseconds.
         */
        *eecd = *eecd & ~E1000_EECD_SK;
        E1000_WRITE_REG(hw, EECD, *eecd);
        E1000_WRITE_FLUSH(hw);
        udelay(50);
}

/******************************************************************************
 * Shift data bits out to the EEPROM.
 *
 * hw - Struct containing variables accessed by shared code
 * data - data to send to the EEPROM
 * count - number of bits to shift out
 *****************************************************************************/
static void
e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count)
{
        uint32_t eecd;
        uint32_t mask;

        /* We need to shift "count" bits out to the EEPROM. So, value in the
         * "data" parameter will be shifted out to the EEPROM one bit at a time.
         * In order to do this, "data" must be broken down into bits.
         */
        mask = 0x01 << (count - 1);
        eecd = E1000_READ_REG(hw, EECD);
        eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
        do {
                /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1",
                 * and then raising and then lowering the clock (the SK bit controls
                 * the clock input to the EEPROM).  A "0" is shifted out to the EEPROM
                 * by setting "DI" to "0" and then raising and then lowering the clock.
                 */
                eecd &= ~E1000_EECD_DI;

                if (data & mask)
                        eecd |= E1000_EECD_DI;

                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);

                udelay(50);

                e1000_raise_ee_clk(hw, &eecd);
                e1000_lower_ee_clk(hw, &eecd);

                mask = mask >> 1;

        } while (mask);

        /* We leave the "DI" bit set to "0" when we leave this routine. */
        eecd &= ~E1000_EECD_DI;
        E1000_WRITE_REG(hw, EECD, eecd);
}

/******************************************************************************
 * Shift data bits in from the EEPROM
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static uint16_t
e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count)
{
        uint32_t eecd;
        uint32_t i;
        uint16_t data;

        /* In order to read a register from the EEPROM, we need to shift 'count'
         * bits in from the EEPROM. Bits are "shifted in" by raising the clock
         * input to the EEPROM (setting the SK bit), and then reading the
         * value of the "DO" bit.  During this "shifting in" process the
         * "DI" bit should always be clear.
         */

        eecd = E1000_READ_REG(hw, EECD);

        eecd &= ~(E1000_EECD_DO | E1000_EECD_DI);
        data = 0;

        for (i = 0; i < count; i++) {
                data = data << 1;
                e1000_raise_ee_clk(hw, &eecd);

                eecd = E1000_READ_REG(hw, EECD);

                eecd &= ~(E1000_EECD_DI);
                if (eecd & E1000_EECD_DO)
                        data |= 1;

                e1000_lower_ee_clk(hw, &eecd);
        }

        return data;
}

/******************************************************************************
 * Returns EEPROM to a "standby" state
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
void e1000_standby_eeprom(struct e1000_hw *hw)
{
        struct e1000_eeprom_info *eeprom = &hw->eeprom;
        uint32_t eecd;

        eecd = E1000_READ_REG(hw, EECD);

        if (eeprom->type == e1000_eeprom_microwire) {
                eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);

                /* Clock high */
                eecd |= E1000_EECD_SK;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);

                /* Select EEPROM */
                eecd |= E1000_EECD_CS;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);

                /* Clock low */
                eecd &= ~E1000_EECD_SK;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);
        } else if (eeprom->type == e1000_eeprom_spi) {
                /* Toggle CS to flush commands */
                eecd |= E1000_EECD_CS;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);
                eecd &= ~E1000_EECD_CS;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(eeprom->delay_usec);
        }
}

/***************************************************************************
* Description:     Determines if the onboard NVM is FLASH or EEPROM.
*
* hw - Struct containing variables accessed by shared code
****************************************************************************/
static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw)
{
        uint32_t eecd = 0;

        DEBUGFUNC();

        if (hw->mac_type == e1000_ich8lan)
                return false;

        if (hw->mac_type == e1000_82573 || hw->mac_type == e1000_82574) {
                eecd = E1000_READ_REG(hw, EECD);

                /* Isolate bits 15 & 16 */
                eecd = ((eecd >> 15) & 0x03);

                /* If both bits are set, device is Flash type */
                if (eecd == 0x03)
                        return false;
        }
        return true;
}

/******************************************************************************
 * Prepares EEPROM for access
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This
 * function should be called before issuing a command to the EEPROM.
 *****************************************************************************/
int32_t e1000_acquire_eeprom(struct e1000_hw *hw)
{
        struct e1000_eeprom_info *eeprom = &hw->eeprom;
        uint32_t eecd, i = 0;

        DEBUGFUNC();

        if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM))
                return -E1000_ERR_SWFW_SYNC;
        eecd = E1000_READ_REG(hw, EECD);

        if (hw->mac_type != e1000_82573 && hw->mac_type != e1000_82574) {
                /* Request EEPROM Access */
                if (hw->mac_type > e1000_82544) {
                        eecd |= E1000_EECD_REQ;
                        E1000_WRITE_REG(hw, EECD, eecd);
                        eecd = E1000_READ_REG(hw, EECD);
                        while ((!(eecd & E1000_EECD_GNT)) &&
                                (i < E1000_EEPROM_GRANT_ATTEMPTS)) {
                                i++;
                                udelay(5);
                                eecd = E1000_READ_REG(hw, EECD);
                        }
                        if (!(eecd & E1000_EECD_GNT)) {
                                eecd &= ~E1000_EECD_REQ;
                                E1000_WRITE_REG(hw, EECD, eecd);
                                DEBUGOUT("Could not acquire EEPROM grant\n");
                                return -E1000_ERR_EEPROM;
                        }
                }
        }

        /* Setup EEPROM for Read/Write */

        if (eeprom->type == e1000_eeprom_microwire) {
                /* Clear SK and DI */
                eecd &= ~(E1000_EECD_DI | E1000_EECD_SK);
                E1000_WRITE_REG(hw, EECD, eecd);

                /* Set CS */
                eecd |= E1000_EECD_CS;
                E1000_WRITE_REG(hw, EECD, eecd);
        } else if (eeprom->type == e1000_eeprom_spi) {
                /* Clear SK and CS */
                eecd &= ~(E1000_EECD_CS | E1000_EECD_SK);
                E1000_WRITE_REG(hw, EECD, eecd);
                udelay(1);
        }

        return E1000_SUCCESS;
}

/******************************************************************************
 * Sets up eeprom variables in the hw struct.  Must be called after mac_type
 * is configured.  Additionally, if this is ICH8, the flash controller GbE
 * registers must be mapped, or this will crash.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static int32_t e1000_init_eeprom_params(struct e1000_hw *hw)
{
        struct e1000_eeprom_info *eeprom = &hw->eeprom;
        uint32_t eecd;
        int32_t ret_val = E1000_SUCCESS;
        uint16_t eeprom_size;

        if (hw->mac_type == e1000_igb)
                eecd = E1000_READ_REG(hw, I210_EECD);
        else
                eecd = E1000_READ_REG(hw, EECD);

        DEBUGFUNC();

        switch (hw->mac_type) {
        case e1000_82542_rev2_0:
        case e1000_82542_rev2_1:
        case e1000_82543:
        case e1000_82544:
                eeprom->type = e1000_eeprom_microwire;
                eeprom->word_size = 64;
                eeprom->opcode_bits = 3;
                eeprom->address_bits = 6;
                eeprom->delay_usec = 50;
                eeprom->use_eerd = false;
                eeprom->use_eewr = false;
        break;
        case e1000_82540:
        case e1000_82545:
        case e1000_82545_rev_3:
        case e1000_82546:
        case e1000_82546_rev_3:
                eeprom->type = e1000_eeprom_microwire;
                eeprom->opcode_bits = 3;
                eeprom->delay_usec = 50;
                if (eecd & E1000_EECD_SIZE) {
                        eeprom->word_size = 256;
                        eeprom->address_bits = 8;
                } else {
                        eeprom->word_size = 64;
                        eeprom->address_bits = 6;
                }
                eeprom->use_eerd = false;
                eeprom->use_eewr = false;
                break;
        case e1000_82541:
        case e1000_82541_rev_2:
        case e1000_82547:
        case e1000_82547_rev_2:
                if (eecd & E1000_EECD_TYPE) {
                        eeprom->type = e1000_eeprom_spi;
                        eeprom->opcode_bits = 8;
                        eeprom->delay_usec = 1;
                        if (eecd & E1000_EECD_ADDR_BITS) {
                                eeprom->page_size = 32;
                                eeprom->address_bits = 16;
                        } else {
                                eeprom->page_size = 8;
                                eeprom->address_bits = 8;
                        }
                } else {
                        eeprom->type = e1000_eeprom_microwire;
                        eeprom->opcode_bits = 3;
                        eeprom->delay_usec = 50;
                        if (eecd & E1000_EECD_ADDR_BITS) {
                                eeprom->word_size = 256;
                                eeprom->address_bits = 8;
                        } else {
                                eeprom->word_size = 64;
                                eeprom->address_bits = 6;
                        }
                }
                eeprom->use_eerd = false;
                eeprom->use_eewr = false;
                break;
        case e1000_82571:
        case e1000_82572:
                eeprom->type = e1000_eeprom_spi;
                eeprom->opcode_bits = 8;
                eeprom->delay_usec = 1;
                if (eecd & E1000_EECD_ADDR_BITS) {
                        eeprom->page_size = 32;
                        eeprom->address_bits = 16;
                } else {
                        eeprom->page_size = 8;
                        eeprom->address_bits = 8;
                }
                eeprom->use_eerd = false;
                eeprom->use_eewr = false;
                break;
        case e1000_82573:
        case e1000_82574:
                eeprom->type = e1000_eeprom_spi;
                eeprom->opcode_bits = 8;
                eeprom->delay_usec = 1;
                if (eecd & E1000_EECD_ADDR_BITS) {
                        eeprom->page_size = 32;
                        eeprom->address_bits = 16;
                } else {
                        eeprom->page_size = 8;
                        eeprom->address_bits = 8;
                }
                if (e1000_is_onboard_nvm_eeprom(hw) == false) {
                        eeprom->use_eerd = true;
                        eeprom->use_eewr = true;

                        eeprom->type = e1000_eeprom_flash;
                        eeprom->word_size = 2048;

                /* Ensure that the Autonomous FLASH update bit is cleared due to
                 * Flash update issue on parts which use a FLASH for NVM. */
                        eecd &= ~E1000_EECD_AUPDEN;
                        E1000_WRITE_REG(hw, EECD, eecd);
                }
                break;
        case e1000_80003es2lan:
                eeprom->type = e1000_eeprom_spi;
                eeprom->opcode_bits = 8;
                eeprom->delay_usec = 1;
                if (eecd & E1000_EECD_ADDR_BITS) {
                        eeprom->page_size = 32;
                        eeprom->address_bits = 16;
                } else {
                        eeprom->page_size = 8;
                        eeprom->address_bits = 8;
                }
                eeprom->use_eerd = true;
                eeprom->use_eewr = false;
                break;
        case e1000_igb:
                /* i210 has 4k of iNVM mapped as EEPROM */
                eeprom->type = e1000_eeprom_invm;
                eeprom->opcode_bits = 8;
                eeprom->delay_usec = 1;
                eeprom->page_size = 32;
                eeprom->address_bits = 16;
                eeprom->use_eerd = true;
                eeprom->use_eewr = false;
                break;
        default:
                break;
        }

        if (eeprom->type == e1000_eeprom_spi ||
            eeprom->type == e1000_eeprom_invm) {
                /* eeprom_size will be an enum [0..8] that maps
                 * to eeprom sizes 128B to
                 * 32KB (incremented by powers of 2).
                 */
                if (hw->mac_type <= e1000_82547_rev_2) {
                        /* Set to default value for initial eeprom read. */
                        eeprom->word_size = 64;
                        ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1,
                                        &eeprom_size);
                        if (ret_val)
                                return ret_val;
                        eeprom_size = (eeprom_size & EEPROM_SIZE_MASK)
                                >> EEPROM_SIZE_SHIFT;
                        /* 256B eeprom size was not supported in earlier
                         * hardware, so we bump eeprom_size up one to
                         * ensure that "1" (which maps to 256B) is never
                         * the result used in the shifting logic below. */
                        if (eeprom_size)
                                eeprom_size++;
                } else {
                        eeprom_size = (uint16_t)((eecd &
                                E1000_EECD_SIZE_EX_MASK) >>
                                E1000_EECD_SIZE_EX_SHIFT);
                }

                eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT);
        }
        return ret_val;
}

/******************************************************************************
 * Polls the status bit (bit 1) of the EERD to determine when the read is done.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static int32_t
e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
{
        uint32_t attempts = 100000;
        uint32_t i, reg = 0;
        int32_t done = E1000_ERR_EEPROM;

        for (i = 0; i < attempts; i++) {
                if (eerd == E1000_EEPROM_POLL_READ) {
                        if (hw->mac_type == e1000_igb)
                                reg = E1000_READ_REG(hw, I210_EERD);
                        else
                                reg = E1000_READ_REG(hw, EERD);
                } else {
                        if (hw->mac_type == e1000_igb)
                                reg = E1000_READ_REG(hw, I210_EEWR);
                        else
                                reg = E1000_READ_REG(hw, EEWR);
                }

                if (reg & E1000_EEPROM_RW_REG_DONE) {
                        done = E1000_SUCCESS;
                        break;
                }
                udelay(5);
        }

        return done;
}

/******************************************************************************
 * Reads a 16 bit word from the EEPROM using the EERD register.
 *
 * hw - Struct containing variables accessed by shared code
 * offset - offset of  word in the EEPROM to read
 * data - word read from the EEPROM
 * words - number of words to read
 *****************************************************************************/
static int32_t
e1000_read_eeprom_eerd(struct e1000_hw *hw,
                        uint16_t offset,
                        uint16_t words,
                        uint16_t *data)
{
        uint32_t i, eerd = 0;
        int32_t error = 0;

        for (i = 0; i < words; i++) {
                eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) +
                        E1000_EEPROM_RW_REG_START;

                if (hw->mac_type == e1000_igb)
                        E1000_WRITE_REG(hw, I210_EERD, eerd);
                else
                        E1000_WRITE_REG(hw, EERD, eerd);

                error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);

                if (error)
                        break;

                if (hw->mac_type == e1000_igb) {
                        data[i] = (E1000_READ_REG(hw, I210_EERD) >>
                                E1000_EEPROM_RW_REG_DATA);
                } else {
                        data[i] = (E1000_READ_REG(hw, EERD) >>
                                E1000_EEPROM_RW_REG_DATA);
                }

        }

        return error;
}

void e1000_release_eeprom(struct e1000_hw *hw)
{
        uint32_t eecd;

        DEBUGFUNC();

        eecd = E1000_READ_REG(hw, EECD);

        if (hw->eeprom.type == e1000_eeprom_spi) {
                eecd |= E1000_EECD_CS;  /* Pull CS high */
                eecd &= ~E1000_EECD_SK; /* Lower SCK */

                E1000_WRITE_REG(hw, EECD, eecd);

                udelay(hw->eeprom.delay_usec);
        } else if (hw->eeprom.type == e1000_eeprom_microwire) {
                /* cleanup eeprom */

                /* CS on Microwire is active-high */
                eecd &= ~(E1000_EECD_CS | E1000_EECD_DI);

                E1000_WRITE_REG(hw, EECD, eecd);

                /* Rising edge of clock */
                eecd |= E1000_EECD_SK;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(hw->eeprom.delay_usec);

                /* Falling edge of clock */
                eecd &= ~E1000_EECD_SK;
                E1000_WRITE_REG(hw, EECD, eecd);
                E1000_WRITE_FLUSH(hw);
                udelay(hw->eeprom.delay_usec);
        }

        /* Stop requesting EEPROM access */
        if (hw->mac_type > e1000_82544) {
                eecd &= ~E1000_EECD_REQ;
                E1000_WRITE_REG(hw, EECD, eecd);
        }

        e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
}

/******************************************************************************
 * Reads a 16 bit word from the EEPROM.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static int32_t
e1000_spi_eeprom_ready(struct e1000_hw *hw)
{
        uint16_t retry_count = 0;
        uint8_t spi_stat_reg;

        DEBUGFUNC();

        /* Read "Status Register" repeatedly until the LSB is cleared.  The
         * EEPROM will signal that the command has been completed by clearing
         * bit 0 of the internal status register.  If it's not cleared within
         * 5 milliseconds, then error out.
         */
        retry_count = 0;
        do {
                e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI,
                        hw->eeprom.opcode_bits);
                spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8);
                if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI))
                        break;

                udelay(5);
                retry_count += 5;

                e1000_standby_eeprom(hw);
        } while (retry_count < EEPROM_MAX_RETRY_SPI);

        /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and
         * only 0-5mSec on 5V devices)
         */
        if (retry_count >= EEPROM_MAX_RETRY_SPI) {
                DEBUGOUT("SPI EEPROM Status error\n");
                return -E1000_ERR_EEPROM;
        }

        return E1000_SUCCESS;
}

/******************************************************************************
 * Reads a 16 bit word from the EEPROM.
 *
 * hw - Struct containing variables accessed by shared code
 * offset - offset of  word in the EEPROM to read
 * data - word read from the EEPROM
 *****************************************************************************/
static int32_t
e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset,
                uint16_t words, uint16_t *data)
{
        struct e1000_eeprom_info *eeprom = &hw->eeprom;
        uint32_t i = 0;

        DEBUGFUNC();

        /* If eeprom is not yet detected, do so now */
        if (eeprom->word_size == 0)
                e1000_init_eeprom_params(hw);

        /* A check for invalid values:  offset too large, too many words,
         * and not enough words.
         */
        if ((offset >= eeprom->word_size) ||
                (words > eeprom->word_size - offset) ||
                (words == 0)) {
                DEBUGOUT("\"words\" parameter out of bounds."
                        "Words = %d, size = %d\n", offset, eeprom->word_size);
                return -E1000_ERR_EEPROM;
        }

        /* EEPROM's that don't use EERD to read require us to bit-bang the SPI
         * directly. In this case, we need to acquire the EEPROM so that
         * FW or other port software does not interrupt.
         */
        if (e1000_is_onboard_nvm_eeprom(hw) == true &&
                hw->eeprom.use_eerd == false) {

                /* Prepare the EEPROM for bit-bang reading */
                if (e1000_acquire_eeprom(hw) != E1000_SUCCESS)
                        return -E1000_ERR_EEPROM;
        }

        /* Eerd register EEPROM access requires no eeprom aquire/release */
        if (eeprom->use_eerd == true)
                return e1000_read_eeprom_eerd(hw, offset, words, data);

        /* Set up the SPI or Microwire EEPROM for bit-bang reading.  We have
         * acquired the EEPROM at this point, so any returns should relase it */
        if (eeprom->type == e1000_eeprom_spi) {
                uint16_t word_in;
                uint8_t read_opcode = EEPROM_READ_OPCODE_SPI;

                if (e1000_spi_eeprom_ready(hw)) {
                        e1000_release_eeprom(hw);
                        return -E1000_ERR_EEPROM;
                }

                e1000_standby_eeprom(hw);

                /* Some SPI eeproms use the 8th address bit embedded in
                 * the opcode */
                if ((eeprom->address_bits == 8) && (offset >= 128))
                        read_opcode |= EEPROM_A8_OPCODE_SPI;

                /* Send the READ command (opcode + addr)  */
                e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits);
                e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2),
                                eeprom->address_bits);

                /* Read the data.  The address of the eeprom internally
                 * increments with each byte (spi) being read, saving on the
                 * overhead of eeprom setup and tear-down.  The address
                 * counter will roll over if reading beyond the size of
                 * the eeprom, thus allowing the entire memory to be read
                 * starting from any offset. */
                for (i = 0; i < words; i++) {
                        word_in = e1000_shift_in_ee_bits(hw, 16);
                        data[i] = (word_in >> 8) | (word_in << 8);
                }
        } else if (eeprom->type == e1000_eeprom_microwire) {
                for (i = 0; i < words; i++) {
                        /* Send the READ command (opcode + addr)  */
                        e1000_shift_out_ee_bits(hw,
                                EEPROM_READ_OPCODE_MICROWIRE,
                                eeprom->opcode_bits);
                        e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i),
                                eeprom->address_bits);

                        /* Read the data.  For microwire, each word requires
                         * the overhead of eeprom setup and tear-down. */
                        data[i] = e1000_shift_in_ee_bits(hw, 16);
                        e1000_standby_eeprom(hw);
                }
        }

        /* End this read operation */
        e1000_release_eeprom(hw);

        return E1000_SUCCESS;
}

/******************************************************************************
 *  e1000_write_eeprom_srwr - Write to Shadow Ram using EEWR
 *  @hw: pointer to the HW structure
 *  @offset: offset within the Shadow Ram to be written to
 *  @words: number of words to write
 *  @data: 16 bit word(s) to be written to the Shadow Ram
 *
 *  Writes data to Shadow Ram at offset using EEWR register.
 *
 *  If e1000_update_eeprom_checksum_i210 is not called after this function, the
 *  Shadow Ram will most likely contain an invalid checksum.
 *****************************************************************************/
static int32_t e1000_write_eeprom_srwr(struct e1000_hw *hw, uint16_t offset,
                                       uint16_t words, uint16_t *data)
{
        struct e1000_eeprom_info *eeprom = &hw->eeprom;
        uint32_t i, k, eewr = 0;
        uint32_t attempts = 100000;
        int32_t ret_val = 0;

        /* A check for invalid values:  offset too large, too many words,
         * too many words for the offset, and not enough words.
         */
        if ((offset >= eeprom->word_size) ||
            (words > (eeprom->word_size - offset)) || (words == 0)) {
                DEBUGOUT("nvm parameter(s) out of bounds\n");
                ret_val = -E1000_ERR_EEPROM;
                goto out;
        }

        for (i = 0; i < words; i++) {
                eewr = ((offset + i) << E1000_EEPROM_RW_ADDR_SHIFT)
                                | (data[i] << E1000_EEPROM_RW_REG_DATA) |
                                E1000_EEPROM_RW_REG_START;

                E1000_WRITE_REG(hw, I210_EEWR, eewr);

                for (k = 0; k < attempts; k++) {
                        if (E1000_EEPROM_RW_REG_DONE &
                            E1000_READ_REG(hw, I210_EEWR)) {
                                ret_val = 0;
                                break;
                        }
                        udelay(5);
                }

                if (ret_val) {
                        DEBUGOUT("Shadow RAM write EEWR timed out\n");
                        break;
                }
        }

out:
        return ret_val;
}

/******************************************************************************
 *  e1000_pool_flash_update_done_i210 - Pool FLUDONE status.
 *  @hw: pointer to the HW structure
 *
 *****************************************************************************/
static int32_t e1000_pool_flash_update_done_i210(struct e1000_hw *hw)
{
        int32_t ret_val = -E1000_ERR_EEPROM;
        uint32_t i, reg;

        for (i = 0; i < E1000_FLUDONE_ATTEMPTS; i++) {
                reg = E1000_READ_REG(hw, EECD);
                if (reg & E1000_EECD_FLUDONE_I210) {
                        ret_val = 0;
                        break;
                }
                udelay(5);
        }

        return ret_val;
}

/******************************************************************************
 *  e1000_update_flash_i210 - Commit EEPROM to the flash
 *  @hw: pointer to the HW structure
 *
 *****************************************************************************/
static int32_t e1000_update_flash_i210(struct e1000_hw *hw)
{
        int32_t ret_val = 0;
        uint32_t flup;

        ret_val = e1000_pool_flash_update_done_i210(hw);
        if (ret_val == -E1000_ERR_EEPROM) {
                DEBUGOUT("Flash update time out\n");
                goto out;
        }

        flup = E1000_READ_REG(hw, EECD) | E1000_EECD_FLUPD_I210;
        E1000_WRITE_REG(hw, EECD, flup);

        ret_val = e1000_pool_flash_update_done_i210(hw);
        if (ret_val)
                DEBUGOUT("Flash update time out\n");
        else
                DEBUGOUT("Flash update complete\n");

out:
        return ret_val;
}

/******************************************************************************
 *  e1000_update_eeprom_checksum_i210 - Update EEPROM checksum
 *  @hw: pointer to the HW structure
 *
 *  Updates the EEPROM checksum by reading/adding each word of the EEPROM
 *  up to the checksum.  Then calculates the EEPROM checksum and writes the
 *  value to the EEPROM. Next commit EEPROM data onto the Flash.
 *****************************************************************************/
static int32_t e1000_update_eeprom_checksum_i210(struct e1000_hw *hw)
{
        int32_t ret_val = 0;
        uint16_t checksum = 0;
        uint16_t i, nvm_data;

        /* Read the first word from the EEPROM. If this times out or fails, do
         * not continue or we could be in for a very long wait while every
         * EEPROM read fails
         */
        ret_val = e1000_read_eeprom_eerd(hw, 0, 1, &nvm_data);
        if (ret_val) {
                DEBUGOUT("EEPROM read failed\n");
                goto out;
        }

        if (!(e1000_get_hw_eeprom_semaphore(hw))) {
                /* Do not use hw->nvm.ops.write, hw->nvm.ops.read
                 * because we do not want to take the synchronization
                 * semaphores twice here.
                 */

                for (i = 0; i < EEPROM_CHECKSUM_REG; i++) {
                        ret_val = e1000_read_eeprom_eerd(hw, i, 1, &nvm_data);
                        if (ret_val) {
                                e1000_put_hw_eeprom_semaphore(hw);
                                DEBUGOUT("EEPROM Read Error while updating checksum.\n");
                                goto out;
                        }
                        checksum += nvm_data;
                }
                checksum = (uint16_t)EEPROM_SUM - checksum;
                ret_val = e1000_write_eeprom_srwr(hw, EEPROM_CHECKSUM_REG, 1,
                                                  &checksum);
                if (ret_val) {
                        e1000_put_hw_eeprom_semaphore(hw);
                        DEBUGOUT("EEPROM Write Error while updating checksum.\n");
                        goto out;
                }

                e1000_put_hw_eeprom_semaphore(hw);

                ret_val = e1000_update_flash_i210(hw);
        } else {
                ret_val = -E1000_ERR_SWFW_SYNC;
        }

out:
        return ret_val;
}

/******************************************************************************
 * Verifies that the EEPROM has a valid checksum
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Reads the first 64 16 bit words of the EEPROM and sums the values read.
 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is
 * valid.
 *****************************************************************************/
static int e1000_validate_eeprom_checksum(struct e1000_hw *hw)
{
        uint16_t i, checksum, checksum_reg, *buf;

        DEBUGFUNC();

        /* Allocate a temporary buffer */
        buf = malloc(sizeof(buf[0]) * (EEPROM_CHECKSUM_REG + 1));
        if (!buf) {
                E1000_ERR(hw, "Unable to allocate EEPROM buffer!\n");
                return -E1000_ERR_EEPROM;
        }

        /* Read the EEPROM */
        if (e1000_read_eeprom(hw, 0, EEPROM_CHECKSUM_REG + 1, buf) < 0) {
                E1000_ERR(hw, "Unable to read EEPROM!\n");
                return -E1000_ERR_EEPROM;
        }

        /* Compute the checksum */
        checksum = 0;
        for (i = 0; i < EEPROM_CHECKSUM_REG; i++)
                checksum += buf[i];
        checksum = ((uint16_t)EEPROM_SUM) - checksum;
        checksum_reg = buf[i];

        /* Verify it! */
        if (checksum == checksum_reg)
                return 0;

        /* Hrm, verification failed, print an error */
        E1000_ERR(hw, "EEPROM checksum is incorrect!\n");
        E1000_ERR(hw, "  ...register was 0x%04hx, calculated 0x%04hx\n",
                  checksum_reg, checksum);

        return -E1000_ERR_EEPROM;
}
#endif /* CONFIG_E1000_NO_NVM */

/*****************************************************************************
 * Set PHY to class A mode
 * Assumes the following operations will follow to enable the new class mode.
 *  1. Do a PHY soft reset
 *  2. Restart auto-negotiation or force link.
 *
 * hw - Struct containing variables accessed by shared code
 ****************************************************************************/
static int32_t
e1000_set_phy_mode(struct e1000_hw *hw)
{
#ifndef CONFIG_E1000_NO_NVM
        int32_t ret_val;
        uint16_t eeprom_data;

        DEBUGFUNC();

        if ((hw->mac_type == e1000_82545_rev_3) &&
                (hw->media_type == e1000_media_type_copper)) {
                ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD,
                                1, &eeprom_data);
                if (ret_val)
                        return ret_val;

                if ((eeprom_data != EEPROM_RESERVED_WORD) &&
                        (eeprom_data & EEPROM_PHY_CLASS_A)) {
                        ret_val = e1000_write_phy_reg(hw,
                                        M88E1000_PHY_PAGE_SELECT, 0x000B);
                        if (ret_val)
                                return ret_val;
                        ret_val = e1000_write_phy_reg(hw,
                                        M88E1000_PHY_GEN_CONTROL, 0x8104);
                        if (ret_val)
                                return ret_val;

                        hw->phy_reset_disable = false;
                }
        }
#endif
        return E1000_SUCCESS;
}

#ifndef CONFIG_E1000_NO_NVM
/***************************************************************************
 *
 * Obtaining software semaphore bit (SMBI) before resetting PHY.
 *
 * hw: Struct containing variables accessed by shared code
 *
 * returns: - E1000_ERR_RESET if fail to obtain semaphore.
 *            E1000_SUCCESS at any other case.
 *
 ***************************************************************************/
static int32_t
e1000_get_software_semaphore(struct e1000_hw *hw)
{
         int32_t timeout = hw->eeprom.word_size + 1;
         uint32_t swsm;

        DEBUGFUNC();

        if (hw->mac_type != e1000_80003es2lan && hw->mac_type != e1000_igb)
                return E1000_SUCCESS;

        while (timeout) {
                swsm = E1000_READ_REG(hw, SWSM);
                /* If SMBI bit cleared, it is now set and we hold
                 * the semaphore */
                if (!(swsm & E1000_SWSM_SMBI))
                        break;
                mdelay(1);
                timeout--;
        }

        if (!timeout) {
                DEBUGOUT("Driver can't access device - SMBI bit is set.\n");
                return -E1000_ERR_RESET;
        }

        return E1000_SUCCESS;
}
#endif

/***************************************************************************
 * This function clears HW semaphore bits.
 *
 * hw: Struct containing variables accessed by shared code
 *
 * returns: - None.
 *
 ***************************************************************************/
static void
e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw)
{
#ifndef CONFIG_E1000_NO_NVM
         uint32_t swsm;

        DEBUGFUNC();

        if (!hw->eeprom_semaphore_present)
                return;

        swsm = E1000_READ_REG(hw, SWSM);
        if (hw->mac_type == e1000_80003es2lan || hw->mac_type == e1000_igb) {
                /* Release both semaphores. */
                swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
        } else
                swsm &= ~(E1000_SWSM_SWESMBI);
        E1000_WRITE_REG(hw, SWSM, swsm);
#endif
}

/***************************************************************************
 *
 * Using the combination of SMBI and SWESMBI semaphore bits when resetting
 * adapter or Eeprom access.
 *
 * hw: Struct containing variables accessed by shared code
 *
 * returns: - E1000_ERR_EEPROM if fail to access EEPROM.
 *            E1000_SUCCESS at any other case.
 *
 ***************************************************************************/
static int32_t
e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw)
{
#ifndef CONFIG_E1000_NO_NVM
        int32_t timeout;
        uint32_t swsm;

        DEBUGFUNC();

        if (!hw->eeprom_semaphore_present)
                return E1000_SUCCESS;

        if (hw->mac_type == e1000_80003es2lan || hw->mac_type == e1000_igb) {
                /* Get the SW semaphore. */
                if (e1000_get_software_semaphore(hw) != E1000_SUCCESS)
                        return -E1000_ERR_EEPROM;
        }

        /* Get the FW semaphore. */
        timeout = hw->eeprom.word_size + 1;
        while (timeout) {
                swsm = E1000_READ_REG(hw, SWSM);
                swsm |= E1000_SWSM_SWESMBI;
                E1000_WRITE_REG(hw, SWSM, swsm);
                /* if we managed to set the bit we got the semaphore. */
                swsm = E1000_READ_REG(hw, SWSM);
                if (swsm & E1000_SWSM_SWESMBI)
                        break;

                udelay(50);
                timeout--;
        }

        if (!timeout) {
                /* Release semaphores */
                e1000_put_hw_eeprom_semaphore(hw);
                DEBUGOUT("Driver can't access the Eeprom - "
                                "SWESMBI bit is set.\n");
                return -E1000_ERR_EEPROM;
        }
#endif
        return E1000_SUCCESS;
}

/* Take ownership of the PHY */
static int32_t
e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask)
{
        uint32_t swfw_sync = 0;
        uint32_t swmask = mask;
        uint32_t fwmask = mask << 16;
        int32_t timeout = 200;

        DEBUGFUNC();
        while (timeout) {
                if (e1000_get_hw_eeprom_semaphore(hw))
                        return -E1000_ERR_SWFW_SYNC;

                swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
                if (!(swfw_sync & (fwmask | swmask)))
                        break;

                /* firmware currently using resource (fwmask) */
                /* or other software thread currently using resource (swmask) */
                e1000_put_hw_eeprom_semaphore(hw);
                mdelay(5);
                timeout--;
        }

        if (!timeout) {
                DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n");
                return -E1000_ERR_SWFW_SYNC;
        }

        swfw_sync |= swmask;
        E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);

        e1000_put_hw_eeprom_semaphore(hw);
        return E1000_SUCCESS;
}

static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask)
{
        uint32_t swfw_sync = 0;

        DEBUGFUNC();
        while (e1000_get_hw_eeprom_semaphore(hw))
                ; /* Empty */

        swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC);
        swfw_sync &= ~mask;
        E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync);

        e1000_put_hw_eeprom_semaphore(hw);
}

static bool e1000_is_second_port(struct e1000_hw *hw)
{
        switch (hw->mac_type) {
        case e1000_80003es2lan:
        case e1000_82546:
        case e1000_82571:
                if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
                        return true;
                /* Fallthrough */
        default:
                return false;
        }
}

#ifndef CONFIG_E1000_NO_NVM
/******************************************************************************
 * Reads the adapter's MAC address from the EEPROM
 *
 * hw - Struct containing variables accessed by shared code
 * enetaddr - buffering where the MAC address will be stored
 *****************************************************************************/
static int e1000_read_mac_addr_from_eeprom(struct e1000_hw *hw,
                                           unsigned char enetaddr[6])
{
        uint16_t offset;
        uint16_t eeprom_data;
        int i;

        for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
                offset = i >> 1;
                if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) {
                        DEBUGOUT("EEPROM Read Error\n");
                        return -E1000_ERR_EEPROM;
                }
                enetaddr[i] = eeprom_data & 0xff;
                enetaddr[i + 1] = (eeprom_data >> 8) & 0xff;
        }

        return 0;
}

/******************************************************************************
 * Reads the adapter's MAC address from the RAL/RAH registers
 *
 * hw - Struct containing variables accessed by shared code
 * enetaddr - buffering where the MAC address will be stored
 *****************************************************************************/
static int e1000_read_mac_addr_from_regs(struct e1000_hw *hw,
                                         unsigned char enetaddr[6])
{
        uint16_t offset, tmp;
        uint32_t reg_data = 0;
        int i;

        if (hw->mac_type != e1000_igb)
                return -E1000_ERR_MAC_TYPE;

        for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) {
                offset = i >> 1;

                if (offset == 0)
                        reg_data = E1000_READ_REG_ARRAY(hw, RA, 0);
                else if (offset == 1)
                        reg_data >>= 16;
                else if (offset == 2)
                        reg_data = E1000_READ_REG_ARRAY(hw, RA, 1);
                tmp = reg_data & 0xffff;

                enetaddr[i] = tmp & 0xff;
                enetaddr[i + 1] = (tmp >> 8) & 0xff;
        }

        return 0;
}

/******************************************************************************
 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the
 * second function of dual function devices
 *
 * hw - Struct containing variables accessed by shared code
 * enetaddr - buffering where the MAC address will be stored
 *****************************************************************************/
static int e1000_read_mac_addr(struct e1000_hw *hw, unsigned char enetaddr[6])
{
        int ret_val;

        if (hw->mac_type == e1000_igb) {
                /* i210 preloads MAC address into RAL/RAH registers */
                ret_val = e1000_read_mac_addr_from_regs(hw, enetaddr);
        } else {
                ret_val = e1000_read_mac_addr_from_eeprom(hw, enetaddr);
        }
        if (ret_val)
                return ret_val;

        /* Invert the last bit if this is the second device */
        if (e1000_is_second_port(hw))
                enetaddr[5] ^= 1;

        return 0;
}
#endif

/******************************************************************************
 * Initializes receive address filters.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Places the MAC address in receive address register 0 and clears the rest
 * of the receive addresss registers. Clears the multicast table. Assumes
 * the receiver is in reset when the routine is called.
 *****************************************************************************/
static void
e1000_init_rx_addrs(struct e1000_hw *hw, unsigned char enetaddr[6])
{
        uint32_t i;
        uint32_t addr_low;
        uint32_t addr_high;

        DEBUGFUNC();

        /* Setup the receive address. */
        DEBUGOUT("Programming MAC Address into RAR[0]\n");
        addr_low = (enetaddr[0] |
                    (enetaddr[1] << 8) |
                    (enetaddr[2] << 16) | (enetaddr[3] << 24));

        addr_high = (enetaddr[4] | (enetaddr[5] << 8) | E1000_RAH_AV);

        E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low);
        E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high);

        /* Zero out the other 15 receive addresses. */
        DEBUGOUT("Clearing RAR[1-15]\n");
        for (i = 1; i < E1000_RAR_ENTRIES; i++) {
                E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0);
                E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0);
        }
}

/******************************************************************************
 * Clears the VLAN filer table
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
static void
e1000_clear_vfta(struct e1000_hw *hw)
{
        uint32_t offset;

        for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++)
                E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
}

/******************************************************************************
 * Set the mac type member in the hw struct.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
int32_t
e1000_set_mac_type(struct e1000_hw *hw)
{
        DEBUGFUNC();

        switch (hw->device_id) {
        case E1000_DEV_ID_82542:
                switch (hw->revision_id) {
                case E1000_82542_2_0_REV_ID:
                        hw->mac_type = e1000_82542_rev2_0;
                        break;
                case E1000_82542_2_1_REV_ID:
                        hw->mac_type = e1000_82542_rev2_1;
                        break;
                default:
                        /* Invalid 82542 revision ID */
                        return -E1000_ERR_MAC_TYPE;
                }
                break;
        case E1000_DEV_ID_82543GC_FIBER:
        case E1000_DEV_ID_82543GC_COPPER:
                hw->mac_type = e1000_82543;
                break;
        case E1000_DEV_ID_82544EI_COPPER:
        case E1000_DEV_ID_82544EI_FIBER:
        case E1000_DEV_ID_82544GC_COPPER:
        case E1000_DEV_ID_82544GC_LOM:
                hw->mac_type = e1000_82544;
                break;
        case E1000_DEV_ID_82540EM:
        case E1000_DEV_ID_82540EM_LOM:
        case E1000_DEV_ID_82540EP:
        case E1000_DEV_ID_82540EP_LOM:
        case E1000_DEV_ID_82540EP_LP:
                hw->mac_type = e1000_82540;
                break;
        case E1000_DEV_ID_82545EM_COPPER:
        case E1000_DEV_ID_82545EM_FIBER:
                hw->mac_type = e1000_82545;
                break;
        case E1000_DEV_ID_82545GM_COPPER:
        case E1000_DEV_ID_82545GM_FIBER:
        case E1000_DEV_ID_82545GM_SERDES:
                hw->mac_type = e1000_82545_rev_3;
                break;
        case E1000_DEV_ID_82546EB_COPPER:
        case E1000_DEV_ID_82546EB_FIBER:
        case E1000_DEV_ID_82546EB_QUAD_COPPER:
                hw->mac_type = e1000_82546;
                break;
        case E1000_DEV_ID_82546GB_COPPER:
        case E1000_DEV_ID_82546GB_FIBER:
        case E1000_DEV_ID_82546GB_SERDES:
        case E1000_DEV_ID_82546GB_PCIE:
        case E1000_DEV_ID_82546GB_QUAD_COPPER:
        case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3:
                hw->mac_type = e1000_82546_rev_3;
                break;
        case E1000_DEV_ID_82541EI:
        case E1000_DEV_ID_82541EI_MOBILE:
        case E1000_DEV_ID_82541ER_LOM:
                hw->mac_type = e1000_82541;
                break;
        case E1000_DEV_ID_82541ER:
        case E1000_DEV_ID_82541GI:
        case E1000_DEV_ID_82541GI_LF:
        case E1000_DEV_ID_82541GI_MOBILE:
                hw->mac_type = e1000_82541_rev_2;
                break;
        case E1000_DEV_ID_82547EI:
        case E1000_DEV_ID_82547EI_MOBILE:
                hw->mac_type = e1000_82547;
                break;
        case E1000_DEV_ID_82547GI:
                hw->mac_type = e1000_82547_rev_2;
                break;
        case E1000_DEV_ID_82571EB_COPPER:
        case E1000_DEV_ID_82571EB_FIBER:
        case E1000_DEV_ID_82571EB_SERDES:
        case E1000_DEV_ID_82571EB_SERDES_DUAL:
        case E1000_DEV_ID_82571EB_SERDES_QUAD:
        case E1000_DEV_ID_82571EB_QUAD_COPPER:
        case E1000_DEV_ID_82571PT_QUAD_COPPER:
        case E1000_DEV_ID_82571EB_QUAD_FIBER:
        case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE:
                hw->mac_type = e1000_82571;
                break;
        case E1000_DEV_ID_82572EI_COPPER:
        case E1000_DEV_ID_82572EI_FIBER:
        case E1000_DEV_ID_82572EI_SERDES:
        case E1000_DEV_ID_82572EI:
                hw->mac_type = e1000_82572;
                break;
        case E1000_DEV_ID_82573E:
        case E1000_DEV_ID_82573E_IAMT:
        case E1000_DEV_ID_82573L:
                hw->mac_type = e1000_82573;
                break;
        case E1000_DEV_ID_82574L:
                hw->mac_type = e1000_82574;
                break;
        case E1000_DEV_ID_80003ES2LAN_COPPER_SPT:
        case E1000_DEV_ID_80003ES2LAN_SERDES_SPT:
        case E1000_DEV_ID_80003ES2LAN_COPPER_DPT:
        case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
                hw->mac_type = e1000_80003es2lan;
                break;
        case E1000_DEV_ID_ICH8_IGP_M_AMT:
        case E1000_DEV_ID_ICH8_IGP_AMT:
        case E1000_DEV_ID_ICH8_IGP_C:
        case E1000_DEV_ID_ICH8_IFE:
        case E1000_DEV_ID_ICH8_IFE_GT:
        case E1000_DEV_ID_ICH8_IFE_G:
        case E1000_DEV_ID_ICH8_IGP_M:
                hw->mac_type = e1000_ich8lan;
                break;
        case PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED:
        case PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED:
        case PCI_DEVICE_ID_INTEL_I210_COPPER:
        case PCI_DEVICE_ID_INTEL_I211_COPPER:
        case PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS:
        case PCI_DEVICE_ID_INTEL_I210_SERDES:
        case PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS:
        case PCI_DEVICE_ID_INTEL_I210_1000BASEKX:
                hw->mac_type = e1000_igb;
                break;
        default:
                /* Should never have loaded on this device */
                return -E1000_ERR_MAC_TYPE;
        }
        return E1000_SUCCESS;
}

/******************************************************************************
 * Reset the transmit and receive units; mask and clear all interrupts.
 *
 * hw - Struct containing variables accessed by shared code
 *****************************************************************************/
void
e1000_reset_hw(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint32_t ctrl_ext;
        uint32_t manc;
        uint32_t pba = 0;
        uint32_t reg;

        DEBUGFUNC();

        /* get the correct pba value for both PCI and PCIe*/
        if (hw->mac_type <  e1000_82571)
                pba = E1000_DEFAULT_PCI_PBA;
        else
                pba = E1000_DEFAULT_PCIE_PBA;

        /* For 82542 (rev 2.0), disable MWI before issuing a device reset */
        if (hw->mac_type == e1000_82542_rev2_0) {
                DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
#ifdef CONFIG_DM_ETH
                dm_pci_write_config16(hw->pdev, PCI_COMMAND,
                                hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
#else
                pci_write_config_word(hw->pdev, PCI_COMMAND,
                                hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
#endif
        }

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        if (hw->mac_type == e1000_igb)
                E1000_WRITE_REG(hw, I210_IAM, 0);
        E1000_WRITE_REG(hw, IMC, 0xffffffff);

        /* Disable the Transmit and Receive units.  Then delay to allow
         * any pending transactions to complete before we hit the MAC with
         * the global reset.
         */
        E1000_WRITE_REG(hw, RCTL, 0);
        E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP);
        E1000_WRITE_FLUSH(hw);

        if (hw->mac_type == e1000_igb) {
                E1000_WRITE_REG(hw, RXPBS, I210_RXPBSIZE_DEFAULT);
                E1000_WRITE_REG(hw, TXPBS, I210_TXPBSIZE_DEFAULT);
        }

        /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */
        hw->tbi_compatibility_on = false;

        /* Delay to allow any outstanding PCI transactions to complete before
         * resetting the device
         */
        mdelay(10);

        /* Issue a global reset to the MAC.  This will reset the chip's
         * transmit, receive, DMA, and link units.  It will not effect
         * the current PCI configuration.  The global reset bit is self-
         * clearing, and should clear within a microsecond.
         */
        DEBUGOUT("Issuing a global reset to MAC\n");
        ctrl = E1000_READ_REG(hw, CTRL);

        E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST));

        /* Force a reload from the EEPROM if necessary */
        if (hw->mac_type == e1000_igb) {
                mdelay(20);
                reg = E1000_READ_REG(hw, STATUS);
                if (reg & E1000_STATUS_PF_RST_DONE)
                        DEBUGOUT("PF OK\n");
                reg = E1000_READ_REG(hw, I210_EECD);
                if (reg & E1000_EECD_AUTO_RD)
                        DEBUGOUT("EEC OK\n");
        } else if (hw->mac_type < e1000_82540) {
                /* Wait for reset to complete */
                udelay(10);
                ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                ctrl_ext |= E1000_CTRL_EXT_EE_RST;
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
                E1000_WRITE_FLUSH(hw);
                /* Wait for EEPROM reload */
                mdelay(2);
        } else {
                /* Wait for EEPROM reload (it happens automatically) */
                mdelay(4);
                /* Dissable HW ARPs on ASF enabled adapters */
                manc = E1000_READ_REG(hw, MANC);
                manc &= ~(E1000_MANC_ARP_EN);
                E1000_WRITE_REG(hw, MANC, manc);
        }

        /* Clear interrupt mask to stop board from generating interrupts */
        DEBUGOUT("Masking off all interrupts\n");
        if (hw->mac_type == e1000_igb)
                E1000_WRITE_REG(hw, I210_IAM, 0);
        E1000_WRITE_REG(hw, IMC, 0xffffffff);

        /* Clear any pending interrupt events. */
        E1000_READ_REG(hw, ICR);

        /* If MWI was previously enabled, reenable it. */
        if (hw->mac_type == e1000_82542_rev2_0) {
#ifdef CONFIG_DM_ETH
                dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
#else
                pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
#endif
        }
        if (hw->mac_type != e1000_igb)
                E1000_WRITE_REG(hw, PBA, pba);
}

/******************************************************************************
 *
 * Initialize a number of hardware-dependent bits
 *
 * hw: Struct containing variables accessed by shared code
 *
 * This function contains hardware limitation workarounds for PCI-E adapters
 *
 *****************************************************************************/
static void
e1000_initialize_hardware_bits(struct e1000_hw *hw)
{
        if ((hw->mac_type >= e1000_82571) &&
                        (!hw->initialize_hw_bits_disable)) {
                /* Settings common to all PCI-express silicon */
                uint32_t reg_ctrl, reg_ctrl_ext;
                uint32_t reg_tarc0, reg_tarc1;
                uint32_t reg_tctl;
                uint32_t reg_txdctl, reg_txdctl1;

                /* link autonegotiation/sync workarounds */
                reg_tarc0 = E1000_READ_REG(hw, TARC0);
                reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27));

                /* Enable not-done TX descriptor counting */
                reg_txdctl = E1000_READ_REG(hw, TXDCTL);
                reg_txdctl |= E1000_TXDCTL_COUNT_DESC;
                E1000_WRITE_REG(hw, TXDCTL, reg_txdctl);

                reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1);
                reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC;
                E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1);


                switch (hw->mac_type) {
                case e1000_igb:                 /* IGB is cool */
                        return;
                case e1000_82571:
                case e1000_82572:
                        /* Clear PHY TX compatible mode bits */
                        reg_tarc1 = E1000_READ_REG(hw, TARC1);
                        reg_tarc1 &= ~((1 << 30)|(1 << 29));

                        /* link autonegotiation/sync workarounds */
                        reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23));

                        /* TX ring control fixes */
                        reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24));

                        /* Multiple read bit is reversed polarity */
                        reg_tctl = E1000_READ_REG(hw, TCTL);
                        if (reg_tctl & E1000_TCTL_MULR)
                                reg_tarc1 &= ~(1 << 28);
                        else
                                reg_tarc1 |= (1 << 28);

                        E1000_WRITE_REG(hw, TARC1, reg_tarc1);
                        break;
                case e1000_82573:
                case e1000_82574:
                        reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                        reg_ctrl_ext &= ~(1 << 23);
                        reg_ctrl_ext |= (1 << 22);

                        /* TX byte count fix */
                        reg_ctrl = E1000_READ_REG(hw, CTRL);
                        reg_ctrl &= ~(1 << 29);

                        E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);
                        E1000_WRITE_REG(hw, CTRL, reg_ctrl);
                        break;
                case e1000_80003es2lan:
        /* improve small packet performace for fiber/serdes */
                        if ((hw->media_type == e1000_media_type_fiber)
                        || (hw->media_type ==
                                e1000_media_type_internal_serdes)) {
                                reg_tarc0 &= ~(1 << 20);
                        }

                /* Multiple read bit is reversed polarity */
                        reg_tctl = E1000_READ_REG(hw, TCTL);
                        reg_tarc1 = E1000_READ_REG(hw, TARC1);
                        if (reg_tctl & E1000_TCTL_MULR)
                                reg_tarc1 &= ~(1 << 28);
                        else
                                reg_tarc1 |= (1 << 28);

                        E1000_WRITE_REG(hw, TARC1, reg_tarc1);
                        break;
                case e1000_ich8lan:
                        /* Reduce concurrent DMA requests to 3 from 4 */
                        if ((hw->revision_id < 3) ||
                        ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
                                (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))
                                reg_tarc0 |= ((1 << 29)|(1 << 28));

                        reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                        reg_ctrl_ext |= (1 << 22);
                        E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext);

                        /* workaround TX hang with TSO=on */
                        reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23));

                        /* Multiple read bit is reversed polarity */
                        reg_tctl = E1000_READ_REG(hw, TCTL);
                        reg_tarc1 = E1000_READ_REG(hw, TARC1);
                        if (reg_tctl & E1000_TCTL_MULR)
                                reg_tarc1 &= ~(1 << 28);
                        else
                                reg_tarc1 |= (1 << 28);

                        /* workaround TX hang with TSO=on */
                        reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24));

                        E1000_WRITE_REG(hw, TARC1, reg_tarc1);
                        break;
                default:
                        break;
                }

                E1000_WRITE_REG(hw, TARC0, reg_tarc0);
        }
}

/******************************************************************************
 * Performs basic configuration of the adapter.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Assumes that the controller has previously been reset and is in a
 * post-reset uninitialized state. Initializes the receive address registers,
 * multicast table, and VLAN filter table. Calls routines to setup link
 * configuration and flow control settings. Clears all on-chip counters. Leaves
 * the transmit and receive units disabled and uninitialized.
 *****************************************************************************/
static int
e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6])
{
        uint32_t ctrl;
        uint32_t i;
        int32_t ret_val;
        uint16_t pcix_cmd_word;
        uint16_t pcix_stat_hi_word;
        uint16_t cmd_mmrbc;
        uint16_t stat_mmrbc;
        uint32_t mta_size;
        uint32_t reg_data;
        uint32_t ctrl_ext;
        DEBUGFUNC();
        /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */
        if ((hw->mac_type == e1000_ich8lan) &&
                ((hw->revision_id < 3) ||
                ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) &&
                (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) {
                        reg_data = E1000_READ_REG(hw, STATUS);
                        reg_data &= ~0x80000000;
                        E1000_WRITE_REG(hw, STATUS, reg_data);
        }
        /* Do not need initialize Identification LED */

        /* Set the media type and TBI compatibility */
        e1000_set_media_type(hw);

        /* Must be called after e1000_set_media_type
         * because media_type is used */
        e1000_initialize_hardware_bits(hw);

        /* Disabling VLAN filtering. */
        DEBUGOUT("Initializing the IEEE VLAN\n");
        /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */
        if (hw->mac_type != e1000_ich8lan) {
                if (hw->mac_type < e1000_82545_rev_3)
                        E1000_WRITE_REG(hw, VET, 0);
                e1000_clear_vfta(hw);
        }

        /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */
        if (hw->mac_type == e1000_82542_rev2_0) {
                DEBUGOUT("Disabling MWI on 82542 rev 2.0\n");
#ifdef CONFIG_DM_ETH
                dm_pci_write_config16(hw->pdev, PCI_COMMAND,
                                      hw->
                                      pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
#else
                pci_write_config_word(hw->pdev, PCI_COMMAND,
                                      hw->
                                      pci_cmd_word & ~PCI_COMMAND_INVALIDATE);
#endif
                E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST);
                E1000_WRITE_FLUSH(hw);
                mdelay(5);
        }

        /* Setup the receive address. This involves initializing all of the Receive
         * Address Registers (RARs 0 - 15).
         */
        e1000_init_rx_addrs(hw, enetaddr);

        /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */
        if (hw->mac_type == e1000_82542_rev2_0) {
                E1000_WRITE_REG(hw, RCTL, 0);
                E1000_WRITE_FLUSH(hw);
                mdelay(1);
#ifdef CONFIG_DM_ETH
                dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
#else
                pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word);
#endif
        }

        /* Zero out the Multicast HASH table */
        DEBUGOUT("Zeroing the MTA\n");
        mta_size = E1000_MC_TBL_SIZE;
        if (hw->mac_type == e1000_ich8lan)
                mta_size = E1000_MC_TBL_SIZE_ICH8LAN;
        for (i = 0; i < mta_size; i++) {
                E1000_WRITE_REG_ARRAY(hw, MTA, i, 0);
                /* use write flush to prevent Memory Write Block (MWB) from
                 * occuring when accessing our register space */
                E1000_WRITE_FLUSH(hw);
        }

        switch (hw->mac_type) {
        case e1000_82545_rev_3:
        case e1000_82546_rev_3:
        case e1000_igb:
                break;
        default:
        /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
        if (hw->bus_type == e1000_bus_type_pcix) {
#ifdef CONFIG_DM_ETH
                dm_pci_read_config16(hw->pdev, PCIX_COMMAND_REGISTER,
                                     &pcix_cmd_word);
                dm_pci_read_config16(hw->pdev, PCIX_STATUS_REGISTER_HI,
                                     &pcix_stat_hi_word);
#else
                pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
                                     &pcix_cmd_word);
                pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI,
                                     &pcix_stat_hi_word);
#endif
                cmd_mmrbc =
                    (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
                    PCIX_COMMAND_MMRBC_SHIFT;
                stat_mmrbc =
                    (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
                    PCIX_STATUS_HI_MMRBC_SHIFT;
                if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K)
                        stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K;
                if (cmd_mmrbc > stat_mmrbc) {
                        pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
                        pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
#ifdef CONFIG_DM_ETH
                        dm_pci_write_config16(hw->pdev, PCIX_COMMAND_REGISTER,
                                              pcix_cmd_word);
#else
                        pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER,
                                              pcix_cmd_word);
#endif
                }
        }
                break;
        }

        /* More time needed for PHY to initialize */
        if (hw->mac_type == e1000_ich8lan)
                mdelay(15);
        if (hw->mac_type == e1000_igb)
                mdelay(15);

        /* Call a subroutine to configure the link and setup flow control. */
        ret_val = e1000_setup_link(hw);

        /* Set the transmit descriptor write-back policy */
        if (hw->mac_type > e1000_82544) {
                ctrl = E1000_READ_REG(hw, TXDCTL);
                ctrl =
                    (ctrl & ~E1000_TXDCTL_WTHRESH) |
                    E1000_TXDCTL_FULL_TX_DESC_WB;
                E1000_WRITE_REG(hw, TXDCTL, ctrl);
        }

        /* Set the receive descriptor write back policy */
        if (hw->mac_type >= e1000_82571) {
                ctrl = E1000_READ_REG(hw, RXDCTL);
                ctrl =
                    (ctrl & ~E1000_RXDCTL_WTHRESH) |
                    E1000_RXDCTL_FULL_RX_DESC_WB;
                E1000_WRITE_REG(hw, RXDCTL, ctrl);
        }

        switch (hw->mac_type) {
        default:

                break;
        case e1000_80003es2lan:
                /* Enable retransmit on late collisions */
                reg_data = E1000_READ_REG(hw, TCTL);
                reg_data |= E1000_TCTL_RTLC;
                E1000_WRITE_REG(hw, TCTL, reg_data);

                /* Configure Gigabit Carry Extend Padding */
                reg_data = E1000_READ_REG(hw, TCTL_EXT);
                reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
                reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX;
                E1000_WRITE_REG(hw, TCTL_EXT, reg_data);

                /* Configure Transmit Inter-Packet Gap */
                reg_data = E1000_READ_REG(hw, TIPG);
                reg_data &= ~E1000_TIPG_IPGT_MASK;
                reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000;
                E1000_WRITE_REG(hw, TIPG, reg_data);

                reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001);
                reg_data &= ~0x00100000;
                E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data);
                /* Fall through */
        case e1000_82571:
        case e1000_82572:
        case e1000_ich8lan:
                ctrl = E1000_READ_REG(hw, TXDCTL1);
                ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH)
                        | E1000_TXDCTL_FULL_TX_DESC_WB;
                E1000_WRITE_REG(hw, TXDCTL1, ctrl);
                break;
        case e1000_82573:
        case e1000_82574:
                reg_data = E1000_READ_REG(hw, GCR);
                reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
                E1000_WRITE_REG(hw, GCR, reg_data);
        case e1000_igb:
                break;
        }

        if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER ||
                hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) {
                ctrl_ext = E1000_READ_REG(hw, CTRL_EXT);
                /* Relaxed ordering must be disabled to avoid a parity
                 * error crash in a PCI slot. */
                ctrl_ext |= E1000_CTRL_EXT_RO_DIS;
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
        }

        return ret_val;
}

/******************************************************************************
 * Configures flow control and link settings.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Determines which flow control settings to use. Calls the apropriate media-
 * specific link configuration function. Configures the flow control settings.
 * Assuming the adapter has a valid link partner, a valid link should be
 * established. Assumes the hardware has previously been reset and the
 * transmitter and receiver are not enabled.
 *****************************************************************************/
static int
e1000_setup_link(struct e1000_hw *hw)
{
        int32_t ret_val;
#ifndef CONFIG_E1000_NO_NVM
        uint32_t ctrl_ext;
        uint16_t eeprom_data;
#endif

        DEBUGFUNC();

        /* In the case of the phy reset being blocked, we already have a link.
         * We do not have to set it up again. */
        if (e1000_check_phy_reset_block(hw))
                return E1000_SUCCESS;

#ifndef CONFIG_E1000_NO_NVM
        /* Read and store word 0x0F of the EEPROM. This word contains bits
         * that determine the hardware's default PAUSE (flow control) mode,
         * a bit that determines whether the HW defaults to enabling or
         * disabling auto-negotiation, and the direction of the
         * SW defined pins. If there is no SW over-ride of the flow
         * control setting, then the variable hw->fc will
         * be initialized based on a value in the EEPROM.
         */
        if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1,
                                &eeprom_data) < 0) {
                DEBUGOUT("EEPROM Read Error\n");
                return -E1000_ERR_EEPROM;
        }
#endif
        if (hw->fc == e1000_fc_default) {
                switch (hw->mac_type) {
                case e1000_ich8lan:
                case e1000_82573:
                case e1000_82574:
                case e1000_igb:
                        hw->fc = e1000_fc_full;
                        break;
                default:
#ifndef CONFIG_E1000_NO_NVM
                        ret_val = e1000_read_eeprom(hw,
                                EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data);
                        if (ret_val) {
                                DEBUGOUT("EEPROM Read Error\n");
                                return -E1000_ERR_EEPROM;
                        }
                        if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0)
                                hw->fc = e1000_fc_none;
                        else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) ==
                                    EEPROM_WORD0F_ASM_DIR)
                                hw->fc = e1000_fc_tx_pause;
                        else
#endif
                                hw->fc = e1000_fc_full;
                        break;
                }
        }

        /* We want to save off the original Flow Control configuration just
         * in case we get disconnected and then reconnected into a different
         * hub or switch with different Flow Control capabilities.
         */
        if (hw->mac_type == e1000_82542_rev2_0)
                hw->fc &= (~e1000_fc_tx_pause);

        if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1))
                hw->fc &= (~e1000_fc_rx_pause);

        hw->original_fc = hw->fc;

        DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc);

#ifndef CONFIG_E1000_NO_NVM
        /* Take the 4 bits from EEPROM word 0x0F that determine the initial
         * polarity value for the SW controlled pins, and setup the
         * Extended Device Control reg with that info.
         * This is needed because one of the SW controlled pins is used for
         * signal detection.  So this should be done before e1000_setup_pcs_link()
         * or e1000_phy_setup() is called.
         */
        if (hw->mac_type == e1000_82543) {
                ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) <<
                            SWDPIO__EXT_SHIFT);
                E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext);
        }
#endif

        /* Call the necessary subroutine to configure the link. */
        ret_val = (hw->media_type == e1000_media_type_fiber) ?
            e1000_setup_fiber_link(hw) : e1000_setup_copper_link(hw);
        if (ret_val < 0) {
                return ret_val;
        }

        /* Initialize the flow control address, type, and PAUSE timer
         * registers to their default values.  This is done even if flow
         * control is disabled, because it does not hurt anything to
         * initialize these registers.
         */
        DEBUGOUT("Initializing the Flow Control address, type"
                        "and timer regs\n");

        /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */
        if (hw->mac_type != e1000_ich8lan) {
                E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE);
                E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH);
                E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW);
        }

        E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time);

        /* Set the flow control receive threshold registers.  Normally,
         * these registers will be set to a default threshold that may be
         * adjusted later by the driver's runtime code.  However, if the
         * ability to transmit pause frames in not enabled, then these
         * registers will be set to 0.
         */
        if (!(hw->fc & e1000_fc_tx_pause)) {
                E1000_WRITE_REG(hw, FCRTL, 0);
                E1000_WRITE_REG(hw, FCRTH, 0);
        } else {
                /* We need to set up the Receive Threshold high and low water marks
                 * as well as (optionally) enabling the transmission of XON frames.
                 */
                if (hw->fc_send_xon) {
                        E1000_WRITE_REG(hw, FCRTL,
                                        (hw->fc_low_water | E1000_FCRTL_XONE));
                        E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
                } else {
                        E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water);
                        E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water);
                }
        }
        return ret_val;
}

/******************************************************************************
 * Sets up link for a fiber based adapter
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Manipulates Physical Coding Sublayer functions in order to configure
 * link. Assumes the hardware has been previously reset and the transmitter
 * and receiver are not enabled.
 *****************************************************************************/
static int
e1000_setup_fiber_link(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint32_t status;
        uint32_t txcw = 0;
        uint32_t i;
        uint32_t signal;
        int32_t ret_val;

        DEBUGFUNC();
        /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
         * set when the optics detect a signal. On older adapters, it will be
         * cleared when there is a signal
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
                signal = E1000_CTRL_SWDPIN1;
        else
                signal = 0;

        printf("signal for %s is %x (ctrl %08x)!!!!\n", hw->name, signal,
               ctrl);
        /* Take the link out of reset */
        ctrl &= ~(E1000_CTRL_LRST);

        e1000_config_collision_dist(hw);

        /* Check for a software override of the flow control settings, and setup
         * the device accordingly.  If auto-negotiation is enabled, then software
         * will have to set the "PAUSE" bits to the correct value in the Tranmsit
         * Config Word Register (TXCW) and re-start auto-negotiation.  However, if
         * auto-negotiation is disabled, then software will have to manually
         * configure the two flow control enable bits in the CTRL register.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause frames, but
         *          not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames but we do
         *          not support receiving pause frames).
         *      3:  Both Rx and TX flow control (symmetric) are enabled.
         */
        switch (hw->fc) {
        case e1000_fc_none:
                /* Flow control is completely disabled by a software over-ride. */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD);
                break;
        case e1000_fc_rx_pause:
                /* RX Flow control is enabled and TX Flow control is disabled by a
                 * software over-ride. Since there really isn't a way to advertise
                 * that we are capable of RX Pause ONLY, we will advertise that we
                 * support both symmetric and asymmetric RX PAUSE. Later, we will
                 *  disable the adapter's ability to send PAUSE frames.
                 */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
                break;
        case e1000_fc_tx_pause:
                /* TX Flow control is enabled, and RX Flow control is disabled, by a
                 * software over-ride.
                 */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR);
                break;
        case e1000_fc_full:
                /* Flow control (both RX and TX) is enabled by a software over-ride. */
                txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
                break;
        }

        /* Since auto-negotiation is enabled, take the link out of reset (the link
         * will be in reset, because we previously reset the chip). This will
         * restart auto-negotiation.  If auto-neogtiation is successful then the
         * link-up status bit will be set and the flow control enable bits (RFCE
         * and TFCE) will be set according to their negotiated value.
         */
        DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw);

        E1000_WRITE_REG(hw, TXCW, txcw);
        E1000_WRITE_REG(hw, CTRL, ctrl);
        E1000_WRITE_FLUSH(hw);

        hw->txcw = txcw;
        mdelay(1);

        /* If we have a signal (the cable is plugged in) then poll for a "Link-Up"
         * indication in the Device Status Register.  Time-out if a link isn't
         * seen in 500 milliseconds seconds (Auto-negotiation should complete in
         * less than 500 milliseconds even if the other end is doing it in SW).
         */
        if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) {
                DEBUGOUT("Looking for Link\n");
                for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) {
                        mdelay(10);
                        status = E1000_READ_REG(hw, STATUS);
                        if (status & E1000_STATUS_LU)
                                break;
                }
                if (i == (LINK_UP_TIMEOUT / 10)) {
                        /* AutoNeg failed to achieve a link, so we'll call
                         * e1000_check_for_link. This routine will force the link up if we
                         * detect a signal. This will allow us to communicate with
                         * non-autonegotiating link partners.
                         */
                        DEBUGOUT("Never got a valid link from auto-neg!!!\n");
                        hw->autoneg_failed = 1;
                        ret_val = e1000_check_for_link(hw);
                        if (ret_val < 0) {
                                DEBUGOUT("Error while checking for link\n");
                                return ret_val;
                        }
                        hw->autoneg_failed = 0;
                } else {
                        hw->autoneg_failed = 0;
                        DEBUGOUT("Valid Link Found\n");
                }
        } else {
                DEBUGOUT("No Signal Detected\n");
                return -E1000_ERR_NOLINK;
        }
        return 0;
}

/******************************************************************************
* Make sure we have a valid PHY and change PHY mode before link setup.
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int32_t
e1000_copper_link_preconfig(struct e1000_hw *hw)
{
        uint32_t ctrl;
        int32_t ret_val;
        uint16_t phy_data;

        DEBUGFUNC();

        ctrl = E1000_READ_REG(hw, CTRL);
        /* With 82543, we need to force speed and duplex on the MAC equal to what
         * the PHY speed and duplex configuration is. In addition, we need to
         * perform a hardware reset on the PHY to take it out of reset.
         */
        if (hw->mac_type > e1000_82543) {
                ctrl |= E1000_CTRL_SLU;
                ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
                E1000_WRITE_REG(hw, CTRL, ctrl);
        } else {
                ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX
                                | E1000_CTRL_SLU);
                E1000_WRITE_REG(hw, CTRL, ctrl);
                ret_val = e1000_phy_hw_reset(hw);
                if (ret_val)
                        return ret_val;
        }

        /* Make sure we have a valid PHY */
        ret_val = e1000_detect_gig_phy(hw);
        if (ret_val) {
                DEBUGOUT("Error, did not detect valid phy.\n");
                return ret_val;
        }
        DEBUGOUT("Phy ID = %x\n", hw->phy_id);

        /* Set PHY to class A mode (if necessary) */
        ret_val = e1000_set_phy_mode(hw);
        if (ret_val)
                return ret_val;
        if ((hw->mac_type == e1000_82545_rev_3) ||
                (hw->mac_type == e1000_82546_rev_3)) {
                ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
                                &phy_data);
                phy_data |= 0x00000008;
                ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL,
                                phy_data);
        }

        if (hw->mac_type <= e1000_82543 ||
                hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 ||
                hw->mac_type == e1000_82541_rev_2
                || hw->mac_type == e1000_82547_rev_2)
                        hw->phy_reset_disable = false;

        return E1000_SUCCESS;
}

/*****************************************************************************
 *
 * This function sets the lplu state according to the active flag.  When
 * activating lplu this function also disables smart speed and vise versa.
 * lplu will not be activated unless the device autonegotiation advertisment
 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
 * hw: Struct containing variables accessed by shared code
 * active - true to enable lplu false to disable lplu.
 *
 * returns: - E1000_ERR_PHY if fail to read/write the PHY
 *            E1000_SUCCESS at any other case.
 *
 ****************************************************************************/

static int32_t
e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active)
{
        uint32_t phy_ctrl = 0;
        int32_t ret_val;
        uint16_t phy_data;
        DEBUGFUNC();

        if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2
            && hw->phy_type != e1000_phy_igp_3)
                return E1000_SUCCESS;

        /* During driver activity LPLU should not be used or it will attain link
         * from the lowest speeds starting from 10Mbps. The capability is used
         * for Dx transitions and states */
        if (hw->mac_type == e1000_82541_rev_2
                        || hw->mac_type == e1000_82547_rev_2) {
                ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO,
                                &phy_data);
                if (ret_val)
                        return ret_val;
        } else if (hw->mac_type == e1000_ich8lan) {
                /* MAC writes into PHY register based on the state transition
                 * and start auto-negotiation. SW driver can overwrite the
                 * settings in CSR PHY power control E1000_PHY_CTRL register. */
                phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
        } else {
                ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                &phy_data);
                if (ret_val)
                        return ret_val;
        }

        if (!active) {
                if (hw->mac_type == e1000_82541_rev_2 ||
                        hw->mac_type == e1000_82547_rev_2) {
                        phy_data &= ~IGP01E1000_GMII_FLEX_SPD;
                        ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO,
                                        phy_data);
                        if (ret_val)
                                return ret_val;
                } else {
                        if (hw->mac_type == e1000_ich8lan) {
                                phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU;
                                E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
                        } else {
                                phy_data &= ~IGP02E1000_PM_D3_LPLU;
                                ret_val = e1000_write_phy_reg(hw,
                                        IGP02E1000_PHY_POWER_MGMT, phy_data);
                                if (ret_val)
                                        return ret_val;
                        }
                }

        /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used during
         * Dx states where the power conservation is most important.  During
         * driver activity we should enable SmartSpeed, so performance is
         * maintained. */
                if (hw->smart_speed == e1000_smart_speed_on) {
                        ret_val = e1000_read_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                        if (ret_val)
                                return ret_val;

                        phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, phy_data);
                        if (ret_val)
                                return ret_val;
                } else if (hw->smart_speed == e1000_smart_speed_off) {
                        ret_val = e1000_read_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                        if (ret_val)
                                return ret_val;

                        phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, phy_data);
                        if (ret_val)
                                return ret_val;
                }

        } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT)
                || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) ||
                (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) {

                if (hw->mac_type == e1000_82541_rev_2 ||
                    hw->mac_type == e1000_82547_rev_2) {
                        phy_data |= IGP01E1000_GMII_FLEX_SPD;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_GMII_FIFO, phy_data);
                        if (ret_val)
                                return ret_val;
                } else {
                        if (hw->mac_type == e1000_ich8lan) {
                                phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU;
                                E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
                        } else {
                                phy_data |= IGP02E1000_PM_D3_LPLU;
                                ret_val = e1000_write_phy_reg(hw,
                                        IGP02E1000_PHY_POWER_MGMT, phy_data);
                                if (ret_val)
                                        return ret_val;
                        }
                }

                /* When LPLU is enabled we should disable SmartSpeed */
                ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
                                &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG,
                                phy_data);
                if (ret_val)
                        return ret_val;
        }
        return E1000_SUCCESS;
}

/*****************************************************************************
 *
 * This function sets the lplu d0 state according to the active flag.  When
 * activating lplu this function also disables smart speed and vise versa.
 * lplu will not be activated unless the device autonegotiation advertisment
 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes.
 * hw: Struct containing variables accessed by shared code
 * active - true to enable lplu false to disable lplu.
 *
 * returns: - E1000_ERR_PHY if fail to read/write the PHY
 *            E1000_SUCCESS at any other case.
 *
 ****************************************************************************/

static int32_t
e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active)
{
        uint32_t phy_ctrl = 0;
        int32_t ret_val;
        uint16_t phy_data;
        DEBUGFUNC();

        if (hw->mac_type <= e1000_82547_rev_2)
                return E1000_SUCCESS;

        if (hw->mac_type == e1000_ich8lan) {
                phy_ctrl = E1000_READ_REG(hw, PHY_CTRL);
        } else if (hw->mac_type == e1000_igb) {
                phy_ctrl = E1000_READ_REG(hw, I210_PHY_CTRL);
        } else {
                ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT,
                                &phy_data);
                if (ret_val)
                        return ret_val;
        }

        if (!active) {
                if (hw->mac_type == e1000_ich8lan) {
                        phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
                        E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
                } else if (hw->mac_type == e1000_igb) {
                        phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU;
                        E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl);
                } else {
                        phy_data &= ~IGP02E1000_PM_D0_LPLU;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP02E1000_PHY_POWER_MGMT, phy_data);
                        if (ret_val)
                                return ret_val;
                }

                if (hw->mac_type == e1000_igb)
                        return E1000_SUCCESS;

        /* LPLU and SmartSpeed are mutually exclusive.  LPLU is used during
         * Dx states where the power conservation is most important.  During
         * driver activity we should enable SmartSpeed, so performance is
         * maintained. */
                if (hw->smart_speed == e1000_smart_speed_on) {
                        ret_val = e1000_read_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                        if (ret_val)
                                return ret_val;

                        phy_data |= IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, phy_data);
                        if (ret_val)
                                return ret_val;
                } else if (hw->smart_speed == e1000_smart_speed_off) {
                        ret_val = e1000_read_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                        if (ret_val)
                                return ret_val;

                        phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, phy_data);
                        if (ret_val)
                                return ret_val;
                }


        } else {

                if (hw->mac_type == e1000_ich8lan) {
                        phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
                        E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl);
                } else if (hw->mac_type == e1000_igb) {
                        phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU;
                        E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl);
                } else {
                        phy_data |= IGP02E1000_PM_D0_LPLU;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP02E1000_PHY_POWER_MGMT, phy_data);
                        if (ret_val)
                                return ret_val;
                }

                if (hw->mac_type == e1000_igb)
                        return E1000_SUCCESS;

                /* When LPLU is enabled we should disable SmartSpeed */
                ret_val = e1000_read_phy_reg(hw,
                                IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                ret_val = e1000_write_phy_reg(hw,
                                IGP01E1000_PHY_PORT_CONFIG, phy_data);
                if (ret_val)
                        return ret_val;

        }
        return E1000_SUCCESS;
}

/********************************************************************
* Copper link setup for e1000_phy_igp series.
*
* hw - Struct containing variables accessed by shared code
*********************************************************************/
static int32_t
e1000_copper_link_igp_setup(struct e1000_hw *hw)
{
        uint32_t led_ctrl;
        int32_t ret_val;
        uint16_t phy_data;

        DEBUGFUNC();

        if (hw->phy_reset_disable)
                return E1000_SUCCESS;

        ret_val = e1000_phy_reset(hw);
        if (ret_val) {
                DEBUGOUT("Error Resetting the PHY\n");
                return ret_val;
        }

        /* Wait 15ms for MAC to configure PHY from eeprom settings */
        mdelay(15);
        if (hw->mac_type != e1000_ich8lan) {
                /* Configure activity LED after PHY reset */
                led_ctrl = E1000_READ_REG(hw, LEDCTL);
                led_ctrl &= IGP_ACTIVITY_LED_MASK;
                led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE);
                E1000_WRITE_REG(hw, LEDCTL, led_ctrl);
        }

        /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */
        if (hw->phy_type == e1000_phy_igp) {
                /* disable lplu d3 during driver init */
                ret_val = e1000_set_d3_lplu_state(hw, false);
                if (ret_val) {
                        DEBUGOUT("Error Disabling LPLU D3\n");
                        return ret_val;
                }
        }

        /* disable lplu d0 during driver init */
        ret_val = e1000_set_d0_lplu_state(hw, false);
        if (ret_val) {
                DEBUGOUT("Error Disabling LPLU D0\n");
                return ret_val;
        }
        /* Configure mdi-mdix settings */
        ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data);
        if (ret_val)
                return ret_val;

        if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) {
                hw->dsp_config_state = e1000_dsp_config_disabled;
                /* Force MDI for earlier revs of the IGP PHY */
                phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX
                                | IGP01E1000_PSCR_FORCE_MDI_MDIX);
                hw->mdix = 1;

        } else {
                hw->dsp_config_state = e1000_dsp_config_enabled;
                phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX;

                switch (hw->mdix) {
                case 1:
                        phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX;
                        break;
                case 2:
                        phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX;
                        break;
                case 0:
                default:
                        phy_data |= IGP01E1000_PSCR_AUTO_MDIX;
                        break;
                }
        }
        ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data);
        if (ret_val)
                return ret_val;

        /* set auto-master slave resolution settings */
        if (hw->autoneg) {
                e1000_ms_type phy_ms_setting = hw->master_slave;

                if (hw->ffe_config_state == e1000_ffe_config_active)
                        hw->ffe_config_state = e1000_ffe_config_enabled;

                if (hw->dsp_config_state == e1000_dsp_config_activated)
                        hw->dsp_config_state = e1000_dsp_config_enabled;

                /* when autonegotiation advertisment is only 1000Mbps then we
                  * should disable SmartSpeed and enable Auto MasterSlave
                  * resolution as hardware default. */
                if (hw->autoneg_advertised == ADVERTISE_1000_FULL) {
                        /* Disable SmartSpeed */
                        ret_val = e1000_read_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, &phy_data);
                        if (ret_val)
                                return ret_val;
                        phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED;
                        ret_val = e1000_write_phy_reg(hw,
                                        IGP01E1000_PHY_PORT_CONFIG, phy_data);
                        if (ret_val)
                                return ret_val;
                        /* Set auto Master/Slave resolution process */
                        ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
                                        &phy_data);
                        if (ret_val)
                                return ret_val;
                        phy_data &= ~CR_1000T_MS_ENABLE;
                        ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
                                        phy_data);
                        if (ret_val)
                                return ret_val;
                }

                ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;

                /* load defaults for future use */
                hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ?
                                ((phy_data & CR_1000T_MS_VALUE) ?
                                e1000_ms_force_master :
                                e1000_ms_force_slave) :
                                e1000_ms_auto;

                switch (phy_ms_setting) {
                case e1000_ms_force_master:
                        phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE);
                        break;
                case e1000_ms_force_slave:
                        phy_data |= CR_1000T_MS_ENABLE;
                        phy_data &= ~(CR_1000T_MS_VALUE);
                        break;
                case e1000_ms_auto:
                        phy_data &= ~CR_1000T_MS_ENABLE;
                default:
                        break;
                }
                ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data);
                if (ret_val)
                        return ret_val;
        }

        return E1000_SUCCESS;
}

/*****************************************************************************
 * This function checks the mode of the firmware.
 *
 * returns  - true when the mode is IAMT or false.
 ****************************************************************************/
bool
e1000_check_mng_mode(struct e1000_hw *hw)
{
        uint32_t fwsm;
        DEBUGFUNC();

        fwsm = E1000_READ_REG(hw, FWSM);

        if (hw->mac_type == e1000_ich8lan) {
                if ((fwsm & E1000_FWSM_MODE_MASK) ==
                    (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
                        return true;
        } else if ((fwsm & E1000_FWSM_MODE_MASK) ==
                       (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT))
                        return true;

        return false;
}

static int32_t
e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data)
{
        uint16_t swfw = E1000_SWFW_PHY0_SM;
        uint32_t reg_val;
        DEBUGFUNC();

        if (e1000_is_second_port(hw))
                swfw = E1000_SWFW_PHY1_SM;

        if (e1000_swfw_sync_acquire(hw, swfw))
                return -E1000_ERR_SWFW_SYNC;

        reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT)
                        & E1000_KUMCTRLSTA_OFFSET) | data;
        E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
        udelay(2);

        return E1000_SUCCESS;
}

static int32_t
e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data)
{
        uint16_t swfw = E1000_SWFW_PHY0_SM;
        uint32_t reg_val;
        DEBUGFUNC();

        if (e1000_is_second_port(hw))
                swfw = E1000_SWFW_PHY1_SM;

        if (e1000_swfw_sync_acquire(hw, swfw)) {
                debug("%s[%i]\n", __func__, __LINE__);
                return -E1000_ERR_SWFW_SYNC;
        }

        /* Write register address */
        reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) &
                        E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN;
        E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val);
        udelay(2);

        /* Read the data returned */
        reg_val = E1000_READ_REG(hw, KUMCTRLSTA);
        *data = (uint16_t)reg_val;

        return E1000_SUCCESS;
}

/********************************************************************
* Copper link setup for e1000_phy_gg82563 series.
*
* hw - Struct containing variables accessed by shared code
*********************************************************************/
static int32_t
e1000_copper_link_ggp_setup(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t phy_data;
        uint32_t reg_data;

        DEBUGFUNC();

        if (!hw->phy_reset_disable) {
                /* Enable CRS on TX for half-duplex operation. */
                ret_val = e1000_read_phy_reg(hw,
                                GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
                /* Use 25MHz for both link down and 1000BASE-T for Tx clock */
                phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ;

                ret_val = e1000_write_phy_reg(hw,
                                GG82563_PHY_MAC_SPEC_CTRL, phy_data);
                if (ret_val)
                        return ret_val;

                /* Options:
                 *   MDI/MDI-X = 0 (default)
                 *   0 - Auto for all speeds
                 *   1 - MDI mode
                 *   2 - MDI-X mode
                 *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
                 */
                ret_val = e1000_read_phy_reg(hw,
                                GG82563_PHY_SPEC_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;

                switch (hw->mdix) {
                case 1:
                        phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
                        break;
                case 2:
                        phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
                        break;
                case 0:
                default:
                        phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
                        break;
                }

                /* Options:
                 *   disable_polarity_correction = 0 (default)
                 *       Automatic Correction for Reversed Cable Polarity
                 *   0 - Disabled
                 *   1 - Enabled
                 */
                phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
                ret_val = e1000_write_phy_reg(hw,
                                GG82563_PHY_SPEC_CTRL, phy_data);

                if (ret_val)
                        return ret_val;

                /* SW Reset the PHY so all changes take effect */
                ret_val = e1000_phy_reset(hw);
                if (ret_val) {
                        DEBUGOUT("Error Resetting the PHY\n");
                        return ret_val;
                }
        } /* phy_reset_disable */

        if (hw->mac_type == e1000_80003es2lan) {
                /* Bypass RX and TX FIFO's */
                ret_val = e1000_write_kmrn_reg(hw,
                                E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL,
                                E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS
                                | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS);
                if (ret_val)
                        return ret_val;

                ret_val = e1000_read_phy_reg(hw,
                                GG82563_PHY_SPEC_CTRL_2, &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
                ret_val = e1000_write_phy_reg(hw,
                                GG82563_PHY_SPEC_CTRL_2, phy_data);

                if (ret_val)
                        return ret_val;

                reg_data = E1000_READ_REG(hw, CTRL_EXT);
                reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK);
                E1000_WRITE_REG(hw, CTRL_EXT, reg_data);

                ret_val = e1000_read_phy_reg(hw,
                                GG82563_PHY_PWR_MGMT_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;

        /* Do not init these registers when the HW is in IAMT mode, since the
         * firmware will have already initialized them.  We only initialize
         * them if the HW is not in IAMT mode.
         */
                if (e1000_check_mng_mode(hw) == false) {
                        /* Enable Electrical Idle on the PHY */
                        phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
                        ret_val = e1000_write_phy_reg(hw,
                                        GG82563_PHY_PWR_MGMT_CTRL, phy_data);
                        if (ret_val)
                                return ret_val;

                        ret_val = e1000_read_phy_reg(hw,
                                        GG82563_PHY_KMRN_MODE_CTRL, &phy_data);
                        if (ret_val)
                                return ret_val;

                        phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
                        ret_val = e1000_write_phy_reg(hw,

                                        GG82563_PHY_KMRN_MODE_CTRL, phy_data);

                        if (ret_val)
                                return ret_val;
                }

                /* Workaround: Disable padding in Kumeran interface in the MAC
                 * and in the PHY to avoid CRC errors.
                 */
                ret_val = e1000_read_phy_reg(hw,
                                GG82563_PHY_INBAND_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;
                phy_data |= GG82563_ICR_DIS_PADDING;
                ret_val = e1000_write_phy_reg(hw,
                                GG82563_PHY_INBAND_CTRL, phy_data);
                if (ret_val)
                        return ret_val;
        }
        return E1000_SUCCESS;
}

/********************************************************************
* Copper link setup for e1000_phy_m88 series.
*
* hw - Struct containing variables accessed by shared code
*********************************************************************/
static int32_t
e1000_copper_link_mgp_setup(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t phy_data;

        DEBUGFUNC();

        if (hw->phy_reset_disable)
                return E1000_SUCCESS;

        /* Enable CRS on TX. This must be set for half-duplex operation. */
        ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
        if (ret_val)
                return ret_val;

        phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX;

        /* Options:
         *   MDI/MDI-X = 0 (default)
         *   0 - Auto for all speeds
         *   1 - MDI mode
         *   2 - MDI-X mode
         *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
         */
        phy_data &= ~M88E1000_PSCR_AUTO_X_MODE;

        switch (hw->mdix) {
        case 1:
                phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE;
                break;
        case 2:
                phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE;
                break;
        case 3:
                phy_data |= M88E1000_PSCR_AUTO_X_1000T;
                break;
        case 0:
        default:
                phy_data |= M88E1000_PSCR_AUTO_X_MODE;
                break;
        }

        /* Options:
         *   disable_polarity_correction = 0 (default)
         *       Automatic Correction for Reversed Cable Polarity
         *   0 - Disabled
         *   1 - Enabled
         */
        phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL;
        ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data);
        if (ret_val)
                return ret_val;

        if (hw->phy_revision < M88E1011_I_REV_4) {
                /* Force TX_CLK in the Extended PHY Specific Control Register
                 * to 25MHz clock.
                 */
                ret_val = e1000_read_phy_reg(hw,
                                M88E1000_EXT_PHY_SPEC_CTRL, &phy_data);
                if (ret_val)
                        return ret_val;

                phy_data |= M88E1000_EPSCR_TX_CLK_25;

                if ((hw->phy_revision == E1000_REVISION_2) &&
                        (hw->phy_id == M88E1111_I_PHY_ID)) {
                        /* Vidalia Phy, set the downshift counter to 5x */
                        phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK);
                        phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X;
                        ret_val = e1000_write_phy_reg(hw,
                                        M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
                        if (ret_val)
                                return ret_val;
                } else {
                        /* Configure Master and Slave downshift values */
                        phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK
                                        | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK);
                        phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X
                                        | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X);
                        ret_val = e1000_write_phy_reg(hw,
                                        M88E1000_EXT_PHY_SPEC_CTRL, phy_data);
                        if (ret_val)
                                return ret_val;
                }
        }

        /* SW Reset the PHY so all changes take effect */
        ret_val = e1000_phy_reset(hw);
        if (ret_val) {
                DEBUGOUT("Error Resetting the PHY\n");
                return ret_val;
        }

        return E1000_SUCCESS;
}

/********************************************************************
* Setup auto-negotiation and flow control advertisements,
* and then perform auto-negotiation.
*
* hw - Struct containing variables accessed by shared code
*********************************************************************/
static int32_t
e1000_copper_link_autoneg(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t phy_data;

        DEBUGFUNC();

        /* Perform some bounds checking on the hw->autoneg_advertised
         * parameter.  If this variable is zero, then set it to the default.
         */
        hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT;

        /* If autoneg_advertised is zero, we assume it was not defaulted
         * by the calling code so we set to advertise full capability.
         */
        if (hw->autoneg_advertised == 0)
                hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT;

        /* IFE phy only supports 10/100 */
        if (hw->phy_type == e1000_phy_ife)
                hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL;

        DEBUGOUT("Reconfiguring auto-neg advertisement params\n");
        ret_val = e1000_phy_setup_autoneg(hw);
        if (ret_val) {
                DEBUGOUT("Error Setting up Auto-Negotiation\n");
                return ret_val;
        }
        DEBUGOUT("Restarting Auto-Neg\n");

        /* Restart auto-negotiation by setting the Auto Neg Enable bit and
         * the Auto Neg Restart bit in the PHY control register.
         */
        ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data);
        if (ret_val)
                return ret_val;

        phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
        ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data);
        if (ret_val)
                return ret_val;

        /* Does the user want to wait for Auto-Neg to complete here, or
         * check at a later time (for example, callback routine).
         */
        /* If we do not wait for autonegtation to complete I
         * do not see a valid link status.
         * wait_autoneg_complete = 1 .
         */
        if (hw->wait_autoneg_complete) {
                ret_val = e1000_wait_autoneg(hw);
                if (ret_val) {
                        DEBUGOUT("Error while waiting for autoneg"
                                        "to complete\n");
                        return ret_val;
                }
        }

        hw->get_link_status = true;

        return E1000_SUCCESS;
}

/******************************************************************************
* Config the MAC and the PHY after link is up.
*   1) Set up the MAC to the current PHY speed/duplex
*      if we are on 82543.  If we
*      are on newer silicon, we only need to configure
*      collision distance in the Transmit Control Register.
*   2) Set up flow control on the MAC to that established with
*      the link partner.
*   3) Config DSP to improve Gigabit link quality for some PHY revisions.
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int32_t
e1000_copper_link_postconfig(struct e1000_hw *hw)
{
        int32_t ret_val;
        DEBUGFUNC();

        if (hw->mac_type >= e1000_82544) {
                e1000_config_collision_dist(hw);
        } else {
                ret_val = e1000_config_mac_to_phy(hw);
                if (ret_val) {
                        DEBUGOUT("Error configuring MAC to PHY settings\n");
                        return ret_val;
                }
        }
        ret_val = e1000_config_fc_after_link_up(hw);
        if (ret_val) {
                DEBUGOUT("Error Configuring Flow Control\n");
                return ret_val;
        }
        return E1000_SUCCESS;
}

/******************************************************************************
* Detects which PHY is present and setup the speed and duplex
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
static int
e1000_setup_copper_link(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t i;
        uint16_t phy_data;
        uint16_t reg_data;

        DEBUGFUNC();

        switch (hw->mac_type) {
        case e1000_80003es2lan:
        case e1000_ich8lan:
                /* Set the mac to wait the maximum time between each
                 * iteration and increase the max iterations when
                 * polling the phy; this fixes erroneous timeouts at 10Mbps. */
                ret_val = e1000_write_kmrn_reg(hw,
                                GG82563_REG(0x34, 4), 0xFFFF);
                if (ret_val)
                        return ret_val;
                ret_val = e1000_read_kmrn_reg(hw,
                                GG82563_REG(0x34, 9), &reg_data);
                if (ret_val)
                        return ret_val;
                reg_data |= 0x3F;
                ret_val = e1000_write_kmrn_reg(hw,
                                GG82563_REG(0x34, 9), reg_data);
                if (ret_val)
                        return ret_val;
        default:
                break;
        }

        /* Check if it is a valid PHY and set PHY mode if necessary. */
        ret_val = e1000_copper_link_preconfig(hw);
        if (ret_val)
                return ret_val;
        switch (hw->mac_type) {
        case e1000_80003es2lan:
                /* Kumeran registers are written-only */
                reg_data =
                E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT;
                reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING;
                ret_val = e1000_write_kmrn_reg(hw,
                                E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data);
                if (ret_val)
                        return ret_val;
                break;
        default:
                break;
        }

        if (hw->phy_type == e1000_phy_igp ||
                hw->phy_type == e1000_phy_igp_3 ||
                hw->phy_type == e1000_phy_igp_2) {
                ret_val = e1000_copper_link_igp_setup(hw);
                if (ret_val)
                        return ret_val;
        } else if (hw->phy_type == e1000_phy_m88 ||
                hw->phy_type == e1000_phy_igb) {
                ret_val = e1000_copper_link_mgp_setup(hw);
                if (ret_val)
                        return ret_val;
        } else if (hw->phy_type == e1000_phy_gg82563) {
                ret_val = e1000_copper_link_ggp_setup(hw);
                if (ret_val)
                        return ret_val;
        }

        /* always auto */
        /* Setup autoneg and flow control advertisement
          * and perform autonegotiation */
        ret_val = e1000_copper_link_autoneg(hw);
        if (ret_val)
                return ret_val;

        /* Check link status. Wait up to 100 microseconds for link to become
         * valid.
         */
        for (i = 0; i < 10; i++) {
                ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
                if (ret_val)
                        return ret_val;
                ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data);
                if (ret_val)
                        return ret_val;

                if (phy_data & MII_SR_LINK_STATUS) {
                        /* Config the MAC and PHY after link is up */
                        ret_val = e1000_copper_link_postconfig(hw);
                        if (ret_val)
                                return ret_val;

                        DEBUGOUT("Valid link established!!!\n");
                        return E1000_SUCCESS;
                }
                udelay(10);
        }

        DEBUGOUT("Unable to establish link!!!\n");
        return E1000_SUCCESS;
}

/******************************************************************************
* Configures PHY autoneg and flow control advertisement settings
*
* hw - Struct containing variables accessed by shared code
******************************************************************************/
int32_t
e1000_phy_setup_autoneg(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t mii_autoneg_adv_reg;
        uint16_t mii_1000t_ctrl_reg;

        DEBUGFUNC();

        /* Read the MII Auto-Neg Advertisement Register (Address 4). */
        ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
        if (ret_val)
                return ret_val;

        if (hw->phy_type != e1000_phy_ife) {
                /* Read the MII 1000Base-T Control Register (Address 9). */
                ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL,
                                &mii_1000t_ctrl_reg);
                if (ret_val)
                        return ret_val;
        } else
                mii_1000t_ctrl_reg = 0;

        /* Need to parse both autoneg_advertised and fc and set up
         * the appropriate PHY registers.  First we will parse for
         * autoneg_advertised software override.  Since we can advertise
         * a plethora of combinations, we need to check each bit
         * individually.
         */

        /* First we clear all the 10/100 mb speed bits in the Auto-Neg
         * Advertisement Register (Address 4) and the 1000 mb speed bits in
         * the  1000Base-T Control Register (Address 9).
         */
        mii_autoneg_adv_reg &= ~REG4_SPEED_MASK;
        mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK;

        DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised);

        /* Do we want to advertise 10 Mb Half Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_10_HALF) {
                DEBUGOUT("Advertise 10mb Half duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
        }

        /* Do we want to advertise 10 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_10_FULL) {
                DEBUGOUT("Advertise 10mb Full duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
        }

        /* Do we want to advertise 100 Mb Half Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_100_HALF) {
                DEBUGOUT("Advertise 100mb Half duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
        }

        /* Do we want to advertise 100 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_100_FULL) {
                DEBUGOUT("Advertise 100mb Full duplex\n");
                mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
        }

        /* We do not allow the Phy to advertise 1000 Mb Half Duplex */
        if (hw->autoneg_advertised & ADVERTISE_1000_HALF) {
                DEBUGOUT
                    ("Advertise 1000mb Half duplex requested, request denied!\n");
        }

        /* Do we want to advertise 1000 Mb Full Duplex? */
        if (hw->autoneg_advertised & ADVERTISE_1000_FULL) {
                DEBUGOUT("Advertise 1000mb Full duplex\n");
                mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
        }

        /* Check for a software override of the flow control settings, and
         * setup the PHY advertisement registers accordingly.  If
         * auto-negotiation is enabled, then software will have to set the
         * "PAUSE" bits to the correct value in the Auto-Negotiation
         * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause frames
         *          but not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames
         *          but we do not support receiving pause frames).
         *      3:  Both Rx and TX flow control (symmetric) are enabled.
         *  other:  No software override.  The flow control configuration
         *          in the EEPROM is used.
         */
        switch (hw->fc) {
        case e1000_fc_none:     /* 0 */
                /* Flow control (RX & TX) is completely disabled by a
                 * software over-ride.
                 */
                mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        case e1000_fc_rx_pause: /* 1 */
                /* RX Flow control is enabled, and TX Flow control is
                 * disabled, by a software over-ride.
                 */
                /* Since there really isn't a way to advertise that we are
                 * capable of RX Pause ONLY, we will advertise that we
                 * support both symmetric and asymmetric RX PAUSE.  Later
                 * (in e1000_config_fc_after_link_up) we will disable the
                 *hw's ability to send PAUSE frames.
                 */
                mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        case e1000_fc_tx_pause: /* 2 */
                /* TX Flow control is enabled, and RX Flow control is
                 * disabled, by a software over-ride.
                 */
                mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
                mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
                break;
        case e1000_fc_full:     /* 3 */
                /* Flow control (both RX and TX) is enabled by a software
                 * over-ride.
                 */
                mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
        }

        ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
        if (ret_val)
                return ret_val;

        DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);

        if (hw->phy_type != e1000_phy_ife) {
                ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL,
                                mii_1000t_ctrl_reg);
                if (ret_val)
                        return ret_val;
        }

        return E1000_SUCCESS;
}

/******************************************************************************
* Sets the collision distance in the Transmit Control register
*
* hw - Struct containing variables accessed by shared code
*
* Link should have been established previously. Reads the speed and duplex
* information from the Device Status register.
******************************************************************************/
static void
e1000_config_collision_dist(struct e1000_hw *hw)
{
        uint32_t tctl, coll_dist;

        DEBUGFUNC();

        if (hw->mac_type < e1000_82543)
                coll_dist = E1000_COLLISION_DISTANCE_82542;
        else
                coll_dist = E1000_COLLISION_DISTANCE;

        tctl = E1000_READ_REG(hw, TCTL);

        tctl &= ~E1000_TCTL_COLD;
        tctl |= coll_dist << E1000_COLD_SHIFT;

        E1000_WRITE_REG(hw, TCTL, tctl);
        E1000_WRITE_FLUSH(hw);
}

/******************************************************************************
* Sets MAC speed and duplex settings to reflect the those in the PHY
*
* hw - Struct containing variables accessed by shared code
* mii_reg - data to write to the MII control register
*
* The contents of the PHY register containing the needed information need to
* be passed in.
******************************************************************************/
static int
e1000_config_mac_to_phy(struct e1000_hw *hw)
{
        uint32_t ctrl;
        uint16_t phy_data;

        DEBUGFUNC();

        /* Read the Device Control Register and set the bits to Force Speed
         * and Duplex.
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
        ctrl &= ~(E1000_CTRL_ILOS);
        ctrl |= (E1000_CTRL_SPD_SEL);

        /* Set up duplex in the Device Control and Transmit Control
         * registers depending on negotiated values.
         */
        if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) {
                DEBUGOUT("PHY Read Error\n");
                return -E1000_ERR_PHY;
        }
        if (phy_data & M88E1000_PSSR_DPLX)
                ctrl |= E1000_CTRL_FD;
        else
                ctrl &= ~E1000_CTRL_FD;

        e1000_config_collision_dist(hw);

        /* Set up speed in the Device Control register depending on
         * negotiated values.
         */
        if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS)
                ctrl |= E1000_CTRL_SPD_1000;
        else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS)
                ctrl |= E1000_CTRL_SPD_100;
        /* Write the configured values back to the Device Control Reg. */
        E1000_WRITE_REG(hw, CTRL, ctrl);
        return 0;
}

/******************************************************************************
 * Forces the MAC's flow control settings.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Sets the TFCE and RFCE bits in the device control register to reflect
 * the adapter settings. TFCE and RFCE need to be explicitly set by
 * software when a Copper PHY is used because autonegotiation is managed
 * by the PHY rather than the MAC. Software must also configure these
 * bits when link is forced on a fiber connection.
 *****************************************************************************/
static int
e1000_force_mac_fc(struct e1000_hw *hw)
{
        uint32_t ctrl;

        DEBUGFUNC();

        /* Get the current configuration of the Device Control Register */
        ctrl = E1000_READ_REG(hw, CTRL);

        /* Because we didn't get link via the internal auto-negotiation
         * mechanism (we either forced link or we got link via PHY
         * auto-neg), we have to manually enable/disable transmit an
         * receive flow control.
         *
         * The "Case" statement below enables/disable flow control
         * according to the "hw->fc" parameter.
         *
         * The possible values of the "fc" parameter are:
         *      0:  Flow control is completely disabled
         *      1:  Rx flow control is enabled (we can receive pause
         *          frames but not send pause frames).
         *      2:  Tx flow control is enabled (we can send pause frames
         *          frames but we do not receive pause frames).
         *      3:  Both Rx and TX flow control (symmetric) is enabled.
         *  other:  No other values should be possible at this point.
         */

        switch (hw->fc) {
        case e1000_fc_none:
                ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE));
                break;
        case e1000_fc_rx_pause:
                ctrl &= (~E1000_CTRL_TFCE);
                ctrl |= E1000_CTRL_RFCE;
                break;
        case e1000_fc_tx_pause:
                ctrl &= (~E1000_CTRL_RFCE);
                ctrl |= E1000_CTRL_TFCE;
                break;
        case e1000_fc_full:
                ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE);
                break;
        default:
                DEBUGOUT("Flow control param set incorrectly\n");
                return -E1000_ERR_CONFIG;
        }

        /* Disable TX Flow Control for 82542 (rev 2.0) */
        if (hw->mac_type == e1000_82542_rev2_0)
                ctrl &= (~E1000_CTRL_TFCE);

        E1000_WRITE_REG(hw, CTRL, ctrl);
        return 0;
}

/******************************************************************************
 * Configures flow control settings after link is established
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Should be called immediately after a valid link has been established.
 * Forces MAC flow control settings if link was forced. When in MII/GMII mode
 * and autonegotiation is enabled, the MAC flow control settings will be set
 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE
 * and RFCE bits will be automaticaly set to the negotiated flow control mode.
 *****************************************************************************/
static int32_t
e1000_config_fc_after_link_up(struct e1000_hw *hw)
{
        int32_t ret_val;
        uint16_t mii_status_reg;
        uint16_t mii_nway_adv_reg;
        uint16_t mii_nway_lp_ability_reg;
        uint16_t speed;
        uint16_t duplex;

        DEBUGFUNC();

        /* Check for the case where we have fiber media and auto-neg failed
         * so we had to force link.  In this case, we need to force the
         * configuration of the MAC to match the "fc" parameter.
         */
        if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed))
                || ((hw->media_type == e1000_media_type_internal_serdes)
                && (hw->autoneg_failed))
                || ((hw->media_type == e1000_media_type_copper)
                && (!hw->autoneg))) {
                ret_val = e1000_force_mac_fc(hw);
                if (ret_val < 0) {
                        DEBUGOUT("Error forcing flow control settings\n");
                        return ret_val;
                }
        }

        /* Check for the case where we have copper media and auto-neg is
         * enabled.  In this case, we need to check and see if Auto-Neg
         * has completed, and if so, how the PHY and link partner has
         * flow control configured.
         */
        if (hw->media_type == e1000_media_type_copper) {
                /* Read the MII Status Register and check to see if AutoNeg
                 * has completed.  We read this twice because this reg has
                 * some "sticky" (latched) bits.
                 */
                if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }

                if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) {
                        /* The AutoNeg process has completed, so we now need to
                         * read both the Auto Negotiation Advertisement Register
                         * (Address 4) and the Auto_Negotiation Base Page Ability
                         * Register (Address 5) to determine how flow control was
                         * negotiated.
                         */
                        if (e1000_read_phy_reg
                            (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }
                        if (e1000_read_phy_reg
                            (hw, PHY_LP_ABILITY,
                             &mii_nway_lp_ability_reg) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }

                        /* Two bits in the Auto Negotiation Advertisement Register
                         * (Address 4) and two bits in the Auto Negotiation Base
                         * Page Ability Register (Address 5) determine flow control
                         * for both the PHY and the link partner.  The following
                         * table, taken out of the IEEE 802.3ab/D6.0 dated March 25,
                         * 1999, describes these PAUSE resolution bits and how flow
                         * control is determined based upon these settings.
                         * NOTE:  DC = Don't Care
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution
                         *-------|---------|-------|---------|--------------------
                         *   0   |    0    |  DC   |   DC    | e1000_fc_none
                         *   0   |    1    |   0   |   DC    | e1000_fc_none
                         *   0   |    1    |   1   |    0    | e1000_fc_none
                         *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
                         *   1   |    0    |   0   |   DC    | e1000_fc_none
                         *   1   |   DC    |   1   |   DC    | e1000_fc_full
                         *   1   |    1    |   0   |    0    | e1000_fc_none
                         *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
                         *
                         */
                        /* Are both PAUSE bits set to 1?  If so, this implies
                         * Symmetric Flow Control is enabled at both ends.  The
                         * ASM_DIR bits are irrelevant per the spec.
                         *
                         * For Symmetric Flow Control:
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   1   |   DC    |   1   |   DC    | e1000_fc_full
                         *
                         */
                        if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                            (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) {
                                /* Now we need to check if the user selected RX ONLY
                                 * of pause frames.  In this case, we had to advertise
                                 * FULL flow control because we could not advertise RX
                                 * ONLY. Hence, we must now check to see if we need to
                                 * turn OFF  the TRANSMISSION of PAUSE frames.
                                 */
                                if (hw->original_fc == e1000_fc_full) {
                                        hw->fc = e1000_fc_full;
                                        DEBUGOUT("Flow Control = FULL.\r\n");
                                } else {
                                        hw->fc = e1000_fc_rx_pause;
                                        DEBUGOUT
                                            ("Flow Control = RX PAUSE frames only.\r\n");
                                }
                        }
                        /* For receiving PAUSE frames ONLY.
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   0   |    1    |   1   |    1    | e1000_fc_tx_pause
                         *
                         */
                        else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                                 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
                        {
                                hw->fc = e1000_fc_tx_pause;
                                DEBUGOUT
                                    ("Flow Control = TX PAUSE frames only.\r\n");
                        }
                        /* For transmitting PAUSE frames ONLY.
                         *
                         *   LOCAL DEVICE  |   LINK PARTNER
                         * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result
                         *-------|---------|-------|---------|--------------------
                         *   1   |    1    |   0   |    1    | e1000_fc_rx_pause
                         *
                         */
                        else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) &&
                                 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) &&
                                 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                                 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR))
                        {
                                hw->fc = e1000_fc_rx_pause;
                                DEBUGOUT
                                    ("Flow Control = RX PAUSE frames only.\r\n");
                        }
                        /* Per the IEEE spec, at this point flow control should be
                         * disabled.  However, we want to consider that we could
                         * be connected to a legacy switch that doesn't advertise
                         * desired flow control, but can be forced on the link
                         * partner.  So if we advertised no flow control, that is
                         * what we will resolve to.  If we advertised some kind of
                         * receive capability (Rx Pause Only or Full Flow Control)
                         * and the link partner advertised none, we will configure
                         * ourselves to enable Rx Flow Control only.  We can do
                         * this safely for two reasons:  If the link partner really
                         * didn't want flow control enabled, and we enable Rx, no
                         * harm done since we won't be receiving any PAUSE frames
                         * anyway.  If the intent on the link partner was to have
                         * flow control enabled, then by us enabling RX only, we
                         * can at least receive pause frames and process them.
                         * This is a good idea because in most cases, since we are
                         * predominantly a server NIC, more times than not we will
                         * be asked to delay transmission of packets than asking
                         * our link partner to pause transmission of frames.
                         */
                        else if (hw->original_fc == e1000_fc_none ||
                                 hw->original_fc == e1000_fc_tx_pause) {
                                hw->fc = e1000_fc_none;
                                DEBUGOUT("Flow Control = NONE.\r\n");
                        } else {
                                hw->fc = e1000_fc_rx_pause;
                                DEBUGOUT
                                    ("Flow Control = RX PAUSE frames only.\r\n");
                        }

                        /* Now we need to do one last check...  If we auto-
                         * negotiated to HALF DUPLEX, flow control should not be
                         * enabled per IEEE 802.3 spec.
                         */
                        e1000_get_speed_and_duplex(hw, &speed, &duplex);

                        if (duplex == HALF_DUPLEX)
                                hw->fc = e1000_fc_none;

                        /* Now we call a subroutine to actually force the MAC
                         * controller to use the correct flow control settings.
                         */
                        ret_val = e1000_force_mac_fc(hw);
                        if (ret_val < 0) {
                                DEBUGOUT
                                    ("Error forcing flow control settings\n");
                                return ret_val;
                        }
                } else {
                        DEBUGOUT
                            ("Copper PHY and Auto Neg has not completed.\r\n");
                }
        }
        return E1000_SUCCESS;
}

/******************************************************************************
 * Checks to see if the link status of the hardware has changed.
 *
 * hw - Struct containing variables accessed by shared code
 *
 * Called by any function that needs to check the link status of the adapter.
 *****************************************************************************/
static int
e1000_check_for_link(struct e1000_hw *hw)
{
        uint32_t rxcw;
        uint32_t ctrl;
        uint32_t status;
        uint32_t rctl;
        uint32_t signal;
        int32_t ret_val;
        uint16_t phy_data;
        uint16_t lp_capability;

        DEBUGFUNC();

        /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be
         * set when the optics detect a signal. On older adapters, it will be
         * cleared when there is a signal
         */
        ctrl = E1000_READ_REG(hw, CTRL);
        if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS))
                signal = E1000_CTRL_SWDPIN1;
        else
                signal = 0;

        status = E1000_READ_REG(hw, STATUS);
        rxcw = E1000_READ_REG(hw, RXCW);
        DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw);

        /* If we have a copper PHY then we only want to go out to the PHY
         * registers to see if Auto-Neg has completed and/or if our link
         * status has changed.  The get_link_status flag will be set if we
         * receive a Link Status Change interrupt or we have Rx Sequence
         * Errors.
         */
        if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) {
                /* First we want to see if the MII Status Register reports
                 * link.  If so, then we want to get the current speed/duplex
                 * of the PHY.
                 * Read the register twice since the link bit is sticky.
                 */
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }
                if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) {
                        DEBUGOUT("PHY Read Error\n");
                        return -E1000_ERR_PHY;
                }

                if (phy_data & MII_SR_LINK_STATUS) {
                        hw->get_link_status = false;
                } else {
                        /* No link detected */
                        return -E1000_ERR_NOLINK;
                }

                /* We have a M88E1000 PHY and Auto-Neg is enabled.  If we
                 * have Si on board that is 82544 or newer, Auto
                 * Speed Detection takes care of MAC speed/duplex
                 * configuration.  So we only need to configure Collision
                 * Distance in the MAC.  Otherwise, we need to force
                 * speed/duplex on the MAC to the current PHY speed/duplex
                 * settings.
                 */
                if (hw->mac_type >= e1000_82544)
                        e1000_config_collision_dist(hw);
                else {
                        ret_val = e1000_config_mac_to_phy(hw);
                        if (ret_val < 0) {
                                DEBUGOUT
                                    ("Error configuring MAC to PHY settings\n");
                                return ret_val;
                        }
                }

                /* Configure Flow Control now that Auto-Neg has completed. First, we
                 * need to restore the desired flow control settings because we may
                 * have had to re-autoneg with a different link partner.
                 */
                ret_val = e1000_config_fc_after_link_up(hw);
                if (ret_val < 0) {
                        DEBUGOUT("Error configuring flow control\n");
                        return ret_val;
                }

                /* At this point we know that we are on copper and we have
                 * auto-negotiated link.  These are conditions for checking the link
                 * parter capability register.  We use the link partner capability to
                 * determine if TBI Compatibility needs to be turned on or off.  If
                 * the link partner advertises any speed in addition to Gigabit, then
                 * we assume that they are GMII-based, and TBI compatibility is not
                 * needed. If no other speeds are advertised, we assume the link
                 * partner is TBI-based, and we turn on TBI Compatibility.
                 */
                if (hw->tbi_compatibility_en) {
                        if (e1000_read_phy_reg
                            (hw, PHY_LP_ABILITY, &lp_capability) < 0) {
                                DEBUGOUT("PHY Read Error\n");
                                return -E1000_ERR_PHY;
                        }
                        if (lp_capability & (NWAY_LPAR_10T_HD_CAPS |
                                             NWAY_LPAR_10T_FD_CAPS |
                                             NWAY_LPAR_100TX_HD_CAPS |
                                             NWAY_LPAR_100TX_FD_CAPS |
                                             NWAY_LPAR_100T4_CAPS)) {
                                /* If our link partner advertises anything in addition to
                                 * gigabit, we do not need to enable TBI compatibility.
                                 */
                                if (hw->tbi_compatibility_on) {
                                        /* If we previously were in the mode, turn it off. */
                                        rctl = E1000_READ_REG(hw, RCTL);
                                        rctl &= ~E1000_RCTL_SBP;
                                        E1000_WRITE_REG(hw, RCTL, rctl);
                                        hw->tbi_compatibility_on = false;
                                }
                        } else {
                                /* If TBI compatibility is was previously off, turn it on. For
                                 * compatibility with a TBI link partner, we will store bad
                                 * packets. Some frames have an additional byte on the end and
                                 * will look like CRC errors to to the hardware.
                                 */
                                if (!hw->tbi_compatibility_on) {
                                        hw->tbi_compatibility_on = true;
                                        rctl = E1000_READ_REG(hw, RCTL);
                                        rctl |= E1000_RCTL_SBP;
                                        E1000_WRITE_REG(hw, RCTL, rctl);
                                }
                        }
                }
        }
        /* If we don't have link (auto-negotiation failed or link partner cannot
         * auto-negotiate), the cable is plugged in (we have signal), and our
         * link partner is not trying to auto-negotiate with us (we are receiving
         * idles or data), we need to force link up. We also need to give
         * auto-negotiation time to complete, in case the cable was just plugged
         * in. The autoneg_failed flag does this.
         */
        else if ((hw->media_type == e1000_media_type_fiber) &&
                 (!(status & E1000_STATUS_LU)) &&
                 ((ctrl & E1000_CTRL_SWDPIN1) == signal) &&
                 (!(rxcw & E1000_RXCW_C))) {
                if (hw->autoneg_failed == 0) {